HYPERX Cloud Buds User Manual
- June 7, 2024
- HYPERX
Table of Contents
User Manual
HyperX Cloud Buds
Find the language and latest documentation for your HyperX Cloud Buds here.
HyperX Cloud Buds Installation Guide
HyperX Cloud Buds
Part Numbers
HEBBXX-MC-RD/G
Overview
A. HyperX Cloud Buds
B. Interchangeable ear tips| C. USB-C charge cable
D. Carrying case
---|---
Specifications
Headphone
Speaker driver: Dynamic with Neodymium magnets
Type: Neckband
Frequency response: 20Hz – 20kHz
Impedance: 65.2 Ω
Sound pressure level: 104±3 dB 1mW at 1kHz
T.H.D: ≦2% at 200-3kHz
Weight: 27.5g
Charge cable length: USB-C to USB-A: 0.2m
Inline Microphone
Element: Electret condenser microphone
Polar pattern: Omni-directional
Frequency response: 100Hz – 7.2kHz
Open circuit sensitivity: -16.5dBV (1V/Pa at1kHz)
**Battery Life***
Bluetooth: 10 hours
Bluetooth
Bluetooth version: 5.1
Wireless range**: Up to 10 meters / 33 feet
Supported codecs: aptX™, aptX™ HD, SBC
Supported profiles: A2DP, AVRCP, HFP, HSP
*Tested at 50% headphone volume
**Wireless range may vary due to environmental conditions
Fitting the HyperX Cloud Buds to your Ears
-
Insert ear tip into ear.
-
Tuck stabilizer flap into ear fold.
Changing Ear Tips
-
Remove original ear tip by gripping the stabilizer flap and stretching ear tip over the hook on the nozzle.
-
Place new ear tip on the nozzle of the ear bud.
-
Pull the stabilizer flap to stretch the nozzle over the hook
Controls
Power Button
Power
On/Off
Hold for 2 seconds to turn on or off.
Bluetooth® Pairing
- With the headset off, hold the power button for 5 seconds to enter pairing mode. The LED indicator will flash red and blue and a voice prompt will play.
- On your Bluetooth® enabled device, search and connect to “HyperX Cloud Buds.” Once connected, the indicator LED will flash blue every 5 seconds and a voice prompt will play.
Volume Buttons 
Press the + and
– buttons to adjust the volume level up or down.
Multifunction Button
| Status | 1 Press | 2 Presses | 3 Presses | Long Press |
|---|---|---|---|---|
| Playing Media | Play/Pause | Skip Track | Previous Track | Activate Mobile |
Assistant
Receiving Call| Answer Call| X| X| Reject Call
In Call| End Call| Swap Calls| X| X
Note: Button functionality may differ depending on the connected device.
Headset Charging
When the headset is connected to a charger with the USB charge cable, the status LED will indicate the charge status. The headset will take approximately 3 hours to fully charge.
| Status LED | Charging Status |
|---|---|
| Breathing red | Charging |
| Off | Fully charged |
Status LED Indicators
The status LED on the headset indicates the current state of the headset.
| Status LED | Headset Status |
|---|---|
| Flash blue every 5 seconds | Connected to a device |
| Flash blue every 2 seconds | Not connected to a device |
| Pairing mode | Flashing red and blue |
| Factory reset | Flash blue 5 times and light up red for 1 second |
Factory Reset
To perform a factory reset on the headset, hold the power and volume up
buttons together for 7 seconds. The status LED will flash red and blue 2
times, followed by solid red for 1 second. At the
same time, the headset will play two low beeps. After this, the headset will
automatically turn off.
Questions or Setup Issues?
Contact the HyperX support team at: hyperxgaming.com/support/headsets
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>