resideo FK76CS/FKN76CS Braukmann User Guide
- June 7, 2024
- resideo
Table of Contents
Filter Combinations
Braukmann
FK76CS/FKN76CS
Reverse rinsing filter combination with rotatable connector flange
APPLICATION
The filter combinations comprise a reverse rinsing filter and pressure
reducing valve in one appliance. They ensure a continuous supply of filtered
water. The fine filter stops the ingress of foreign bodies, for example, rust
particles, strands of hemp and grains of sand and thus reduces the probability
of corrosion. The pressure-reducing valve prevents pressure damage and reduces
water consumption.
All individual units correspond to the requirements of current DIN/DVGW
specifications. Technical features of each unit also apply to the combination
assembly.
APPROVALS
- DVGW
approval for all filters with 100 μm mesh sizes
SPECIAL FEATURES
-
Double Spin Technology
– Cartridge with external rotor enabling simultaneous
cleaning in lower and upper filter areas
– Visual function check possible -
Balanced seat valve
-
Filtered water supplied even during reverse rinsing
-
Patented reverse rinsing system – fast and thorough cleaning of the filter with a small amount of water
-
Memory ring indicates when the next manual reverse rinsing is due
-
Automatic reverse rinsing actuator with bayonet the connector can be retrofitted
-
Shock-resistant clear synthetic material filter bowl enables easy checking of filter contamination
-
Inlet pressure balancing – no influence on the outlet pressure by fluctuating inlet pressure
-
Valve and filter inserts are fully interchangeable
-
Large filter surface
-
Filter and complete filter bowl are replaceable
-
Standardized discharge connection
-
All materials are KTW approved
-
Approved by TÜV LGA for low noise, Group 1 without limitations
TECHNICAL DATA
Media
Medium:| Drinking water
Connections/Sizes
Connection sizes:| 3/4″ – 1 /4″
Pressure values
Operating pressure range:| 1.5 – 16 bar
Max. inlet pressure with clear filter bowl:| 16 bar
Outlet pressure:| 1.5 – 6 bar
Operating temperatures
Operating temperature range medium accord. to 1567:| 5 °C – 30 °C
Specifications
Installation position:| Horizontal or vertical, with filter bowl downwards
Note:
The filter is constructed for drinking water installations. In the case of a
process water application, the filter has to be proven individually.
CONSTRUCTION
Overview | Components | Materials |
---|
| | Spring bonnet with adjustment knob and
setting scale| High-quality synthetic material
| Threaded male connections| Brass
| Rotatable connector piece (FK76CS only)| Red bronze
| Housing with pressure gauge| Red bronze
| Fine filter in clear filter bowl| Shock-resistant, clear transparent
synthetic material filter bowl, stainless steel fine filter
| Ball valve with drain connection| Brass (Ball Valve body), Stainless steel
(ball), Plasticdurethan (drain adapter)
| Not depicted components:
| Valve insert complete with diaphragm and valve seat| High-quality synthetic
material, fibre- einforced NBR diaphragm
Double wring wrench| Plastic
Seals| NBR
METHOD OF OPERATION
The filter combination combines reverse rinsing filter and pressure reducing
valve in one appliance.
The downstream reverse rinsing fine filter holds back any dirt particles in
the water. These particles are then completely flushed out by reverse rinsing.
Filters with Double Spin Technology have turbine blades that circulate the
water and thereby set the rotor on the upper filter into a rotational motion.
The internal impeller rinses off particles that have adhered to the upper
filter at the intersecting points with the rotor.
The integral pressure reducing valve functions on a balanced force principle
whereby the force exerted by a diaphragm is balanced against the force of an
adjustment spring. The inlet pressure has no influence on the opening or
closing of the valve. Inlet pressure fluctuation does not, therefore, affect
the outlet pressure.
TRANSPORTATION AND STORAGE
Keep parts in their original packaging and unpack them shortly before use.
The following parameters apply during transportation and storage:
Parameter | Value |
---|---|
Environment: | clean, dry, and dust-free |
Min. ambient temperature: | 5 °C |
Max. ambient temperature: | 55 °C |
Min. ambient relative humidity: | 25 % * |
Max. ambient relative humidity: | 85 % * |
*non condensing
INSTALLATION GUIDELINES
Setup requirements
-
Install in horizontal or vertical pipework with filter bowl downwards
– This position ensures optimum filter efficiency -
Install shut-off valves
-
These filters are armatures that need to be maintained regularly
-
Ensure good access
– Pressure gauge can be read off easily
– Degree of contamination can be easily seen with a clear filter bowl
– Simplifies maintenance and inspection -
The installation location should be protected against frost
-
Fit immediately after the water meter
-
Related to the EN 806-2 it is recommended to install the filter immediately after the water meter
-
In order to avoid flooding, it is recommended to arrange a permanent, professionally dimensioned wastewater connection
Installation Example
**TECHNICAL CHARACTERISTICS
**
kvs-Values
Connection sizes: | 15 | 20 | 25 | 32 |
---|---|---|---|---|
kvs-value (m 3 /h): | 4.5 | 5.8 | 6.2 | 6.5 |
Pressure drop characteristics
DIMENSIONS
Overview
Parameter|
Values
---|---
Connection sizes:| R| 3 /4″| 1″| 1¹/4″
Nominal sizes:| DN| 20| 25| 32
Weight:| kg| 3.9| 4.0| 4.1
Dimensions:| L| 158| 179| 197
T| 177| 177| 181
t| 95| 95| 99
H| 493| 493| 493
h| 363| 363| 363
D| 97| 97| 97
DVGW registration number:| NW-9311AT2317
Note: All dimensions in mm unless stated otherwise.
ORDERING INFORMATION
The following tables contain all the information you need to make an order of an item of your choice. When ordering, please always state the type, the ordering or the part number.
Options
The filter combination is available in the following sizes: 3 /4″, 1″, and 1
¹/4″.
• standard
– not available
| | FK76CS-…AA| FKN76CS-1A
---|---|---|---
Connection type:| Filter mesh size 100 μm, incl. rotatable connector piece
DA74C with threaded male connections| •| –
Filter mesh size 100 μm, rotatable connector piece DA74C has to be ordered
separately – see accessories| –| •
Note: = space holder for connection size
Accessories
| Description| | Dimension| Part No.
---|---|---|---|---
| Z11S| Automatic reverse rinsing actuator
For automatic filter cleaning at presettable intervals
| 230 V, 50/60 Hz, 10 with molded Schuko electrical plug| Z11S-A
24 V, 50/60 Hz, 10 without an electrical plug| Z11S-B
230 V, 50/60 Hz, 10 with molded Type 12 electrical plug for Switzerland|
Z11S-Z
|
ZA76C| Connector piece
For conversion of the fine filters with rotatable connector pieces (1¹ /4″ and
1 1 /2″) into retrofit filter combinations (Converts 63 mm hole centers to 45
mm hole centers)
| | 3 /4″| ZA76C-3/4A
1| ZA76C-1A
1 ¹/4″| ZA76C-11/4A
| VST06B| Connection set
Solder connections
| | 1 /2″| VST06-1/2B
3 /4″| VST06-3/4B
1″| VST06-1B
1 ¹/4″| VST06-11/4B
1 ¹ /2″| VST06-11/2B
2″| VST06-2B
| DA74C| Rotatable connector piece
For connection of retrofit filters FN76CS.
| 3 /4″| DA74C-3/4A
| 1″| DA74C-1A
1 /4| DA74C-11/4A
|
ZR10K| Double ring wrench for removing the filter bowl
|
| 1 ³/2″ + /4″| ZR10K-1/2
1 1″ + 1 /4″| ZR10K-1
1 ¹/2″ + 2″| ZR10K-11/2
Spare Parts
Filter combinations FK76CS / FKN76CS from 1997 onwards
Overview
*The filter guide (either with double spin or without the double spin feature) is included in the packaging of the replacement filter inserts (AF11DS and AF11S) only for the sizes 1/2″ up to 1 ¹/4″!
Manufactured for and on behalf of Pittway Sàrl, Z.A., La Pièce 4, 1180 Rolle, Switzerland by its authorized representative Ademco 1 GmbH
For more information
homecomfort.resideo.com/europe
Ademco 1 GmbH, Hardhofweg 40, 74821 MOSBACH, GERMANY
Phone: +49 6261 810
Fax: +49 6261 81309
Subject to change. EN0H-1104GE23 R0420
© 2020 Resideo Technologies, Inc. All rights reserved.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>