Sheffield LABS TLPC12QC Nexus Wireless Charging LED Desk Lamp User Manual

Sheffield LABS TLPC12QC Nexus Wireless Charging LED Desk Lamp

PLEASE READ BEFORE USING

If you find that you have any trouble or missing or damaged parts please contact us.
If you need installation assistance, replacement parts or have questions regarding our warranty, please contact our product consultants at [email protected] or call toll free: 1-800-936-3213
Monday to Friday from 9:00 a.m. to 5:00 p.m., EST. English and Spanish spoken. International Regions: Please contact your local distributor.

WARRANTY

• Sheffield Labs products are manufactured under the highest quality and workmanship standards. Sheffield Labs guarantees the original buyer that this product will be free of fabrication, material and finish defects for one year period starting at the purchase date. Sheffield Labs recommends professional installation for this product.
• Should this product present any leaks derived from a fabrication or material defect during the warranty period, Sheffield Labs will supply the necessary replacement parts free of charge. Sheffield Labs will also replace any pieces presenting defects in finish or fabrication. This warranty is only valid under normal installation, use and service conditions.
• This warranty does not apply to any damage caused by normal wearing of the product, incorrect installation or operation, alterations or modifications performed by parties not authorized by Sheffield Labs, or the use of replacement parts any brand other than Sheffield Labs. This warranty also excludes damages caused by the use of abrasive cleaners, containing alcohol or other organic solvents; whether the damage was caused by the consumer or third parties. Sheffield Labs will not be responsible for workmanship expenses, damages incurred during the installation, repair or replacement, or for any direct, indirect, consequent damage or losses related to this product.
• This warranty being Sheffield Labs sole responsibility, leaving no further right or actions to the original buyer or third parties and liberating Enchante Lites New York and any other subsidiaries, affiliates, shareholders, distributors, retailers, representatives, agents and employees of these or any other responsibility for visible or hidden defects or damages of any kind.
• The purchase, use and ownership of this product implies acceptance on behalf of the original buyer of the terms and conditions of this warranty.
• In order for the original buyer to make this warranty valid any claim must be accompanied by an original purchase ticket. To make this warranty valid write Sheffield Labs to the email below with subject: “Sheffield Labs Warranty”. Explain the kind of defect and include the purchase ticket (original), your full name and address, and phone number. Should the claim be compliant with warranty limitations, all necessary replacement parts will be mailed at no cost to the customer.

[email protected]
1-800-936-3213
Monday to Friday from 9:00 am to 5:00 pm

Thank you for purchasing Sheffield Labs product. AlI Sheffield Labs products are carefully engineered and factory tested for durability under normal conditions. We develop our products for simple installation. Follow our instructions to help you easily install your Sheffield Labs LED Desk lamp.

SAVE THESE INSTRUCTIONS AND READ CAREFULLY BEFORE USE For Customer Care, production operation information or problem resolution, call toll-free 1-800-936-3213

IMPORTANT SAFETY INSTRUCTIONS

WARNING : TO PREVENT ELECTRIC SHOCK, MAKE SURE THE Lil LAMP IS NOT PLUGGED IN UNTIL All STEPS ARE COMPLETE.
WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS TURN LAMP OFF AND WAIT UNTIL LED PANEL (D) AND ADAPTER (G) ARE COOL BEFORE HANDLING

• The LED panel (D) might get hot after several hours of continuous use. DO NOT place your hands directly on LED light panel.
• Never use with an extension cord unless the plug can be fully inserted into the receptacles in the extension cord.
• Do not alter the plug.
• The lamp head included with this unit cannot be replaced by the consumer.
• Do not place flammable material near or overthe lamp.
• Ensure the lamp is not installed next to any air vents and is not in any moist or damp areas.
• INDOOR USE ONLY

NOTE: The important safety instructions appearing in this manual are not meant to cover all possible conditions and situations that may occur. It must be understood that common sense, caution, and care must be used with any electrical product.
CAUTION: Any change or modification to this product not expressly recognized by Enchante Lites LLC voids Enchante’s responsibility for proper function of product.

B

C

| Lamp Body

Lamp Shade

D| LEDPanel
E

F

| Power Adapter Input

Power Connector

G| Power Adapter
H

I

| Power Switch

Wireless ChargingPad

J| USB-APort

INSTRUCTIONS

NOTE : THIS UNIT IS FULLY ASSEMBLED

1. Remove lamp from packing, placing lamp base (A) flat on a steady surface.

2. Connect power connector (F) into power adapter input (E) at the rear-bottom of the lamp.

3. Plug the power adapter(G) into a standard household 120V AC outlet.
   NOTE : Only use with the supplied power adapter to avoid damage or risk offire.

4. Power switch (H) is a touch-sensor that controls ON/OFF power, the LED brightness settings and the color mode functions of the lamps.

5. Touch button (H) to turn the lamp ON/OFF and adjust the brightness.

6. Touching and holding button (H) will allow you to toggle through the three color modes.

7. Wireless charging: Place your compatible device face up on the middle of the Qi wireless charging pad (I).
   NOTE : Device will charge in horizontal position only. A red indicator light in the center of power switch (H) will illuminate to indicate the device is charging. Check the charge level on your device periodically to determine when device is fully charged.

8. USB charging: This lamp contains a USB-A charging port (J) located next to the rear power input (E). Simply connect any compatible device with your USB cord to begin charging.

9. To reposition the lamp head simply move the shade (C) as needed to point the light in the desired direction.
   Please hold the lamp base (A) while adjusting the head.
   NOTE : DO NOT FORCE the shade (C) outside allowable adjustable range as excessive adjustment may cause damage.

The “Qi” symbol is a trademark of the Wireless Power Consortium. All mobile devices with integrated wireless charging support “Qi”.

IC CANADA : This device contains licence-exempt transmitters)/receiver that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions:

1. This device may not cause interference.
2. This device must accept any interference, including interference that may cause undesired operation of the device.

IC RF RADIATION EXPOSURE STATEMENT CAUTION: To maintain compliance with the RF exposure guidelines, place the product at least 10cm from nearby persons.

CAN RSS -216/CNR-216
CAN ICES -OOS(B)/NMB-005 (B)

Dimension

PRODUCT SPECIFICATIONS

PRODUCT MAINTENANCE

1. Always ensure the power is OFF and the lamp has cooled down before performing any maintenance, cleaning or adjustments.
2. To avoid injury or damage to the lamp, ensure that the adapter and any screws are secure before reconnecting to power.
3. To clean, wipe with a damp or dry clean cloth. Never soak the lamp with water.

FCC statement

This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: 1) this device may not cause harmful interference, and 2) this device must accept any interference received, including interference that may cause undesired operation.
Note : This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Radiation Exposure Statement

This device complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. During the operation of device a distance of 15 cm surrounding the device and 20 cm above the top surface of thedevicemust be respected.
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licenceexempt RSS(s). Operation is subject to the following two conditions:

1. This device may not cause interference.
2. This device must accept any interference, including interference that may cause undesired operation of the device.

Market: Canada
Brand: Sheffield Labs
Model #: TLPC12QC-WHT
Product: LED table lamp
Art Size : 100%
Dims: 11″ x 8.5″ (27.94cm x 21.59cm)
File Name: TLPC120C-WHT_JMArtwork_190CT22.pdf
Date: 190CT22
Printing : Non-coated, Double sided print (front and back)

THIS PACKAGING ARTWORK MUST NOT BE ALTERED!

• Any alterations must be approved by the packaging department of AMG, Ench-Lites (Enchante Accessories).
• If revisions are made without the express permission of the packaging design dept, responsible supplier will be charged back.

NOTE:
There will be a total of 6 sheets printed front and back. Once the pages are printed and folded in half, Please staple the pages on the folded crease, forming an 12 page booklet.

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>