BERNSTEIN SHOWER CABIN EX102 Instruction Manual
- June 7, 2024
- BERNSTEIN
Table of Contents
- DUSCHKABINE EX102
- MONTAGEANLEITUNG – III / 2020
- 5.A VARIANTE A /VARIANTE B: INSTALLATION WAND
- 5.B VARIANTE A /VARIANTE B: INSTALLATION WAND
- 5.C VARIANTE A /VARIANTE B: INSTALLATION WAND
- 6. VARIANTE A: INSTALLATION
- 7. VARIANTE A /VARIANTE B:
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
DUSCHKABINE EX102
MONTAGEANLEITUNG – III / 2020
ASSEMBLY INSTRUCTIONS
VARIANTE A VARIANTE B
NEEDED TOOLS
2. DELIVERY
Wall steel section
OPTIONAL
Floor steel section
REMARK:
- Support bar and floor steel section available as options.
- From a shower enclosure width of 1300mm, support bar will be recommended.
3. VARIANTE B:
3. ASSEMBLY OF TWO SHOWER ENCLOSURES - B VARIANT:
Please follow coming instructions, if you own the EX102 shower with two shower enclosures (variant B):
- If one of your shower walls is wider than 1200mm, then please assemble it as described in section 6 with support bar as an option.
- The use of a support bar is recommended for shock absorption. The larger your product is, the greater the risk is that the shower enclosure vibrates as a result of a shock. Starting from a width of > 1200 mm, the installation of a support bar is STRONGLY recommended. The bar can also be installed later on.
- Please note that only one shower screen can be fixed with a support bar. The smallest one should not be wider than 1200 mm.
- If your second enclosure is 700 mm large and you want to fix the first shower enclosure with a support bar, then the two walls will not be at the same level. See figure b.
- Install both shower enclosure as shown in point 5.
4. INSTALLATION POSSIBILITIES FOR FLOOR AND WALL STEEL SECTION
Installation of the wall and/or floor steel section in a tiled floor. Sealing with silicone. Please note that the steel section must be installed before tiles.
Installation of the wall and/or floor steel section on a tiled floor. Sealing with silicone.
The installation should only be done with corner protection (already installed) and silicone (not included). CAUTION: only for installation on the floor.
5.A VARIANTE A /VARIANTE B: INSTALLATION WAND
5A. VARIANTE A/VARIANTE B: WALL AND FLOOR STEEL SECTION ASSEMBLY
- Secure the stainless steel wall steel section with screws, by fixing them into it. When screwing them in the steel section, please make sure that the screws are well fastened, in order not to damage the glass.
- These instructions are also valid for a floor steel section installation
- If you use a support bar, the wall and floor steel sections should be installed 760 –1400 mm away from the wall.
- The point number 3 is particularly important if you own the variant B including a second shower screen 700 mm width. In this case, both shower walls won´t be at the same level, see figure B under section 3. If you do not use a support bar, then you can choose the distance from the wall.
- If you have subfloor heating and do not wish to drill holes in the floor, the steel section can also be fixed with high performance hybrid glue.
5.B VARIANTE A /VARIANTE B: INSTALLATION WAND
BITTE BEACHTEN
PLEASE NOTE
5.B VARIANTE A /VARIANTE B: WALL AND FLOOR STEEL SECTION ASSEMBLY
- Add silicone inside and between wall steel section and floor steel section (if you select a floor steel section).
- Slide the shower glass into the floor steel section and slowly in the wall steel section.
- Adjust the shower in the right position.
5.C VARIANTE A /VARIANTE B: INSTALLATION WAND
5C. VARIANTE A/VARIANTE B: WALL AND FLOOR STEEL SECTION INSTALLATION
- Adjust the position of the glass again.
- Install the support bar as described in section 7 (if you select a support bar).
- Sealing inside and outside edges of the steel section with silicone.
6. VARIANTE A: INSTALLATION
6. VARIANTE A: INSTALLATION WITHOUT FLOOR STEEL SECTION
- Install the steel section and the shower enclosure as shown in points 5A and 5B. Please make sure that the shower enclosure seal is directed to the floor side.
- Apply silicone on both side of the sealing.
- If you want to install a support bar, please follow instructions on point 7.
- We recommend using a support bar when installing a shower enclosure without floor steel section.
7. VARIANTE A /VARIANTE B:
7. VARIANTE A/VARIANTE B: SUPPORT BAR ASSEMBLY
- Check the positioning of the shower enclosure and adjust it if necessary.
- Fix the support bar with a screw on the wall, as shown hereby.
- Please note that the minimum length of the support bar is 760 mm and a maximum length 1400 mm. The width of your shower with support bar should be between 760 and 1400 mm.
- The use of a support bar is recommended for shock absorption. The larger your product is, the greater the risk is that the shower enclosure vibrates as a result of a shock. Starting from a width of > 1200 mm, the installation of a support bar is STRONGLY recommended. The bar can also be installed later on.
MAINTENANCE:
- Use only a soft cloth and clear water to clean the profiles and glasses of the shower enclosure.
- Please do not use any corrosive chemicals or detergents to remove the To clean shower cubicle.
- Avoid cleaning with scratching objects. For stubborn stains you can clean with low-concentration vinegar, if you rinse afterwards with plenty of water.
- Regularly wipe the components of the cotton with a damp cotton cloth shower.
- Please do not clean the shower cubicle with toilet cleaner. If accidentally should spray toilet cleaner on the shower enclosure, then immediately rinse the areas with clear water.
BITTE BEACHTEN
PLEASE NOTE
Arrows point upwards on the outside. No arrow: Usable on both sides.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>