BOSE SUB1 POWERED BASS MODULE Instruction Manual
- June 7, 2024
- Bose
Table of Contents
PROFESSIONAL
PRELIMINARY TECHNICAL DATA
SUB1
POWERED BASS MODULE
Product Overview
A powered, portable bass module, the Sub1 subwoofer combines with virtually any portable PA and delivers low-end performance down to 40 Hz. It’s unique 7″ × 13″ high-excursion RaceTrack driver allows for an ultraslim enclosure, delivering a performance that rivals a traditional 12″ woofer without the cumbersome size, freeing up room in your vehicle and on the stage. Compared to the ub2 subwoofer, Sub1 is the more compact subwoofer option for the Bose L1 Pro32 system, combining seamlessly via single-cable SubMatch connectivity. You can stack multiple Sub1 subwoofers for even more low-end — or to unleash Cardioid Mode for directional bass. With a Sub1, you get a subwoofer that goes virtually anywhere and effortlessly fills out your sound.
Key Features
Add powerful bass to your portable PA system with a low-end range down to
40 Hz
Go from vehicle to venue easily with a slim design featuring a unique 7″
× 13″ high-excursion RaceTrack driver; a performance that rivals a
conventional 12″ woofer with a smaller footprint
Stack multiple Sub1 subwoofers for even more bass or unleash Cardioid
Mode for focused, a directional performance that steers the bass out front and
decreases feedback
Combine seamlessly with Bose L1 Pro32 portable line array via proprietary
SubMatch connectivity, which delivers both power and audio over a single cable
Pair with other powered loudspeakers via line input and output with
selectable crossover modes, plus integrated threaded pole mount for use with
Bose S1 Pro PA and more
Technical Specifications
System Performance
Model Name| Sub1
System Type| Self-powered bass module
Frequency Response (-3 dB) ‘| 40 Hz to 180 Hz
Frequency Range (-10 dB)| 32 Hz to 250 Hz
Nominal Vertical Coverage Pattern| 0°
Nominal Horizontal Coverage Pattern| Omnidirectional (with -10 dB rear
rejection in Cardioid mode)
Calculated Maximum SPL Cal 1 m, continuous :| 118.6 dB
Calculated Maximum SPL Cal 1 m, peak 2| 124.6 dB
Crossover| 200 Hz
Transducers
Low Frequency| 1 x RaceTrack low-frequency driver T x 13–
Low-Frequency Voice Coil Size| 2′
Driver Protection| Dynamic limiting
Amplification|
Type| Class D
Low-Frequency Amplifier Channel| 480 W
Cooling| Convection cooling
Onboard Mixer|
Channels| Two
Channel l& 2 Input: Audio Type| Combination XLR or ‘A” TRS connector
(mic/instrument/line)
Channel 1 & 2 Input: Impedance| 100 KG
Channel 1 & 2 Input: Channel Gain| +10 dB to +45 dB: from input to driver,
controlled by the volume control
Channel 1 & 2 Input: Max Input Signal| +24 dBu
Channel 1 & 2 Output: Audio Type| XLR connector, line-level. full-frequency
bandwidth
sub match Input: Audio Type| Bose proprietary multi-pin cable
sub match Thruput: Audio Type| Bose proprietary multi-pin cable
LED Indicators| Standby. Phase/Pattern selection. Input EQ selection, Output
EQ selection. Signal/Clip Indicator
AC Power
AC Power Input| 100-240 VAC (±20%. 50/60 Hz)
Input: Electrical Type| IEC. sub match
Initial turn-on inrush current| 14.9 A at 120 V: 29.3 A at 230 V
Inrush current after AC mains interruption of 5s| 5.8 A at 120 V: 32.0 A at
230 V
Enclosure
Color| Black
Enclosures Material| High-impact polypropylene, birch plywood
Grille Material| Powder-coated perforated steel
Product Dimensions (H x W x D)| 533 x 260 x 529 mm (21.0 x 10.2 x 20.8 in)
Shipping Dimensions (H x W x D)| 620 x 620 x 330 mm (24.41 x 24.41 x 12.99 in)
Net Weight‘| 15.5 kg (34.1 Ibs)
Shipping Weight| 18.0 kg (39.6 Ibs)
Warranty Period| 2 years
Included Accessories| IEC power cord, slipcover
Optional Accessories| Sub Roller Bag, Adjustable Speaker Pole, SubMatch Cable
Product Part Numbers
840918-1100| SUB1 POWERED BASS MODULE,120V,US
840918-2100| SUB1 POWERED BASS MODULE,230V,EU
840918-3100| SUB1 POWERED BASS MODULE,100V,JP
840918-4100| SUB1 POWERED BASS MODULE,230V,UK
840918-5100| SUB1 POWERED BASS MODULE,230V,AU
840918-5130| SUB1 POWERED BASS MODULE,230V,INDIA
856985-0110| PREMIUM ROLLER BAG, SUBI, BLACK
857172-0110| sub match CABLE, BLACK
857000-0110| SPEAKER STAND,SUB POLE,BLACK
Footnotes
(1) Frequency response and range measured on-axis in an anechoic environment
with recommended bandpass and EQ.
(2) Maximum SPL calculated using sensitivity and power ratings, exclusive of
power compression.
(3) Net weight excludes slipcover and power cord.
Connections and Controls
-
Standby Button: Press the button to power on the Sub. The LED will illuminate white while the Sub is on.
-
Line Inputs: Analog input for connecting an L1 Pro or another line-level audio source. Compatible with XLR, TRS balanced, and TS unbalanced cables.
-
Line Outputs: Use an XLR cable to connect the line-level output to a loudspeaker.
-
sub match Thruput: Connect an additional Sub-bass module with a SubMatch cable. Up to two Sub1 or Sub2 powered bass
modules can be powered by a single L1 Pro32 via a SubMatch connection. -
Power Input Cover: Prevents simultaneous use of the SubMatch Input and Power Input. Slide the cover to reveal the power input that is needed for setup.
-
sub match Input: Connect the Sub to an L1 Pro32 with a SubMatch cable.
-
Power Input: IEC power cord connection.
-
westinghouse.com.au/manualsUSB-C connector for Bose service use and firmware updates.
Note: This port is not compatible with Thunderbolt 3 cables. -
Line Output EQ: Select between FULL bandwidth or a multi-purpose HPF when using Line Outputs. Press the button to switch EQ settings. The corresponding LED will illuminate white while selected.
-
Line Input EQ: Select between an optimized EQ for an L1 Pro or a multipurpose LPF when using Line Inputs. Press the button to switch EQ settings. The corresponding LED will illuminate white while selected.
-
Signal/Clip Indicator : The LED will illuminate green when a signal is present and will illuminate red when the signal is clipping or the Sub is entering limiting. Reduce the level or signal volume to prevent signal clipping or limiting.
-
Level Control: Adjust the level of audio output. The Level Control does not affect the Line Outputs. The 12 o’clock position is recommended when in use with an L1 Pro32.
-
Phase/Pattern Button: Adjust the polarity of the Sub. Press the button to switch polarity. The corresponding LED will illuminate white while selected. Also allows access to Cardioid mode when using two identical Submodules.
Product Dimensions
Performance
Frequency Response (On-Axis)
Architect and Engineer Specification
The sub shall be a single-driver, subwoofer with internally supplied power
amplification and active equalization for multiple operating modes as follows:
The sub shall consist of a modular 7″ x 13″ (177 mm x 330 mm) RaceTrack low-
frequency driver mounted in a ported bass enclosure.
The nominal horizontal beamwidth of the loudspeaker shall be omnidirectional,
with a –10 dB rear rejection when in Cardioid mode. The nominal vertical
coverage shall be 0°. The power amplification for transducers shall be
supplied by an integral single-channel onboard amplifier providing 480 W for
the low-frequency transducer.
The onboard digital mixer shall consist of two input channels. Each input
channel shall provide two combination XLR or 1/4″ TRS connectors (line-level)
with selectable equalization presets for low-pass filter and L1 optimization.
Each input channel shall also provide an XLR balanced line-level connector
with selectable equalization presets for full bandwidth, high-pass filter, and
S1 Pro optimization. The digital mixer shall provide master output level
control and phase/pattern control for the positive polarity, negative
polarity, and Cardioid mode. The sub shall provide multi-pin SubMatch input
and output connectors to receive power from L1 Pro32 and send power to another
Sub1/Sub2 with a Bose SubMatch cable.
The enclosure of the sub shall be constructed of high-impact polypropylene and
birch plywood. The sub shall provide a pole-mount M20 threaded insert for use
with the Bose Sub1/Sub2 Adjustable Speaker Pole. The sub shall provide four
interlocking feet on each side for stacking with one other Sub1.
The sub’s dimensions shall be 21.0″ H × 10.2″ W × 20.8″ D (533 mm × 260 mm ×
529 mm). Its net weight shall be 34.1 lbs (15.5 kg).
The sub shall be the Bose Sub1 portable powered bass module.
Safety and Regulatory Compliance
The Sub1 powered bass module complies with the following standards:
- UL/IEC/EN62368-1 Audio/Video, Information, and Communication Technology Equipment
- Ecodesign Requirements for Energy Related Products Directive 2009/125/EC
- Radio Equipment Directive 2014/53/EU
- CAN ICES-3 (B)/NMB-3(B)
- FCC Part 15 Class B
Bose, L1, and ToneMatch are trademarks of Bose Corporation. All other trademarks are the property of their respective owners.
For additional specifications and application information, please visit
PRO.BOSE.COM.
Specifications are subject to change without notice. 6/2021
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>