Concox WeTrack2 General Vehicle GPS Tracker User Manual

June 7, 2024
Concox

Concox WeTrack2 General Vehicle GPS Tracker User Manual
Concox WeTrack2 General Vehicle GPS Tracker

Introducing Your Device

Learn about your device’s layout, indications and specifications.

Inside the Box

Check your product box for the following items:

  • * Device
    • Charging cab
    • Relay
    • Relay socket
    • User manual

Overview

LED Indications

Power indicator (red) Indication
Quick Flashing (flash 0 3s at interval of 0.3s) Low battery
Solid red Charging
Flashing (flash 1s at interval of 3s) Full Charge
OFF Power off or low battery

Slow flashing (flash 0’1

at interval of 3s)

| Working normally

GPS indicator (blue) Indication
Flashing (ON:0.3S, OFF:0.3S) Searching GPS signal
Slow flashing (flash 0 1s at interval of 3s) Receive GPS signal normally
OFF No GPS signal
GSM indicator (green) Indication
Quick Flashing (flash 0.3s at interval of 0.3s) GSM initializing
Flashing (flash 1s at interval of 3s) Receive GSM signal normally
Solid green In communication with phones
OFF No GSM signal or no SIM card
Slow flashing (flash 0 1 at interval of 3s) GPRS on line

Specifications

Dimension 78.0(L) x 41.0(W) x 13.0(H) mm
Weight 38g
Working voltage 9-90V
BaCkup Battery 270mAh / 3.7V
Operation Temperature -20°C – 70°C
Humidity 20% – 80%
Standby Time 60 hours
GSM Frequencies 850/900/1800/1900 MHz
GPRS Class 12, TCP/IP
GPS Channel 32
GPS Sensitivity -162dBm
Acquisition Sensitivity -148dBm
Position Accuracy < 10m
TTFF (Open Sky) Cold Start: < 35s
  Hot Start: < 1s
GSM/GPS Antenna Built-in design
LED Indicator GSM-green, GPS-blue, Power-red
Data Transmit TCP, SMS
Geo-fence Alarm Alarm when get in or get out a

specified area

Speeding Alarm| Report when speeds hipher than

the pre-set value.

Low Power Alarm| Alarm when backup battery is

running out

Non-movement Detection| Movement alarm based on built-in 3D motion sensor
Mileage Report| Track by time/distance interval
Remote Control| Cut off petrol/electricity

Getting Started

Switch on

Get started by assembling and setting up your device for its first use.

  1. Open the SIM card

  2. Insert the SIM

    NOTE:
    SIM card should be equipped with GPRS and SMS functions.

  3. Turn the battery switch to ON.

  4. Close the SIM card cover and connect the device with the external power line which will be used to charge the terminal and built-in battery.

Switch off

  1. Toggle the battery switch to OFF.

Charge the device

Plug the device connector into a charging cable.
The charging cable with 1A FUSE for short-circuit over current protection.

NOTE:

Improperly connecting the charging cable can cause serious damage to the device. Any damages by misuse are not covered by the warranty

Install the device

You need to choose somewhere that it won’t be found.

  1. Your device has built-in GSM antenna and GPS antenna. During installation, please make sure the receiving side face is up ; any high power devices such as reversing radar, anti-theft device or communication equipment would affect the signal of the device.
  2. All metallic cases of the windshield will attenuate the signal on the tracking device. It’s simply due to the shielding effects of the metal compound of the case.
  3. The device should be fixed into position with cable ties or wide double-side tape.

Installation please refers to below picture.

  • Under the dash board below the front windshield;
  • In the parcel shelf in the rear;
  • In the front bumper (non-material face), make sure the device does not get wet;
  • Under the wiper version (non-metal), make sure the device does not get wet;
  • Non Covert Installation – fix the device on the dash board below

Dev1ce Wiring

  1. Since the recharging voltage can be much higher than the working voltage, for your safety, please use with vehicle battery voltage no more than 72V. The red wire is the positive, the black wire is the negative.
  2. Connect the black wire to ground.

Device wiring d1agram

NOTE:
Please pay attention to the diagram description, battery is no more than 72V and relay remains 12V/ 24V

Power/ACC/Tele-cutoff(petrol/electricity) control line (4 pin)

  1. Your device comes with a power cord and is designed to use only manufacturer-specified original device. The red line is positive while the black one is negative (the side should not be connected with ground wire).
  2. The ACC line (orange) connects to ACC switch of the Please be sure to connect the ACC line; otherwise the device won’t enter ignition detection status when disconnect the ACC line. If you don’t need to anti-theft temporarily, just connect the ACC line to the positive side in parallel.
  3. Tele-cutoff(petrol/ electricity) control line (yellow) is connected to pin 86 of the Tele-cutoff (petrol/ electricity) relay (equal to the yellow line of the relay socket).

Quick Operation Instructions

To properly use the device, common parameters should be set before initial use. This can be done by using the parameter editor or by sending SMS commands to the device. (“,”should be English comma and no space before and after the comma)

Add SOS number

SMS command to the device to add the SOS number.

SOS,A,No.1,No.2,No.3#

“A” means to add new numbers, for example:

SOS,A,18165542975,18165542976,18165542977#

It will reply

“OK! SOS1: 18165542975 SOS2: 18165542976 SOS3:

18165542977″ after set successfully.

APN setting

To ensure GPRS is activated, please make sure APN is correct. You can send SMS command to set APN: APN command format APN,APN’s Name# E.g: APN,internet# ( “internet” is the APN of carrier) The device will reply “OK” if setting successfully. Note: The APN of some countries have user name and password, you may need to send SMS command as following: APN,APN name, user name ,password#

Server setting

Default platform is www.tracksoIid.com

To connect to other platform, please send the SMS command to change the DNS or server IP: DNS : SERVER,1,DNS,Port,0# E.g: SERVER,1,gpsdev.tracksoIid.com,21 1 00,0# IP: SERVER,0,IP,Port,0# It will reply “OK” after set successfully.

Set the center number

If you want to cut off/restore oil by SMS command, you have to set a center number firstly. Only the center number can send the cut off/restore oil command to the device. You can set your own mobile number as center number. The command for setting center number is: CENTER,A,mobile number# E.g. CENTER,A,18165542976# If set successfully, there is an “OK” reply message.

NOTE:
Only the SOS number can be used to add or delete center number successfully. There is only one center number can be set.

Locator Data Upload Interval
Users can modify GPRS uploading time interval by SMS

TIMER,T1,T2#
T1 ranges 5-18000 or 0(seconds), upload interval when ACC ON, 0 means no upload, default is 20;
T2 ranges 5-18000 or 0(seconds), upload interval when ACC OFF, 0 means no upload, default is 20

Arming time setting

Delay time for device entering arming state after the vehicle power is off and ACC is in low-level. In the arming state, if the vehicle vibrates for a few times, it will activate the vibration alarm system. If the vehicle battery is still not on (ACC is in low level) after 3 minutes, the device will start vibration alarm.

SMS format:

DEFENSE,TIME#

The time ranges from 1 to 60 minutes, default is 1.

NOTE:

  1. Preset SOS numbers before sending SMS alarm messages and
  2. If there is no need for vibration alarm, please SMS SENALM,OFF# to close it.

Check parameter setting

You can check the parameter setting by command:

PARAM#

Example: PARAM# Information replied:
IMEI: 358735070292023; TIMER: 20,20; SENDS:3; SOS:„;
Center Number:; Sensorset:10,3,5,1; Defense time:1; TimeZone:E,8,0;
The replied information contains IMEI number GPS data uploading Interval, GPS working time, SOS number center number, sensor time interval, defense time and time zone info.

Check GPRS parameters
SMS command format :
GPRSSET#
Example: GPRSSET# Reply message:
GPRS:ON; Currently use APN:cmmtm„; Server:1,
GPSDEV.TRACKSOLID.COM,21100,0;
URL:http://maps.googIe.com/maps?q=;

Operation of device

Power on/Power off

Power on: Once insert a valid SIM card and connect all the wires, turn on the device, then Power LED will flash first, during signal searching process, GSM and GPS LED will flash. Once GPS LED keeps slow flashing, it means the device has been located and it starts to work. Power off: Just turn off the power switch. The device will begin to upload positioning data to server once inserting a valid SIM card and power on. During the working time, it can upload data to server every 10 seconds.

NOTE:

To power on / power off, please remove the back cover first, refer to 4. Getting Started.

Check location

  1. Via SMS
    SMS “WHERE# ’ to the SIM number of device. The device will send a location message automatically. You can get the coordinates. If the device does not search any information of location, it will send “No data” to the cell phone. Example: Current position! Lat:N22.577156,Lon:E113.916748,Course:131.99,Speed:0. 00Km/h,Date Time:2013-10-08 17:35:32 SMS “URL# ’ to the SIM number of device. The device will send a location Google Map link. If the device does not search any information of location, it will send “No data” to the cell phone. Example: <1 0-08 17:36>http://maps.googIe.com/maps?q=N22.5771 56,E1 13.916748

  2. V1a platform
    **** Go to the platform website offered by dealers to check your vehicle location.

Wire cut-off alarm

When the electricity supply of device is cut off, it will activate cut-off alarm. In this case, the device will send related SMS to the SOS numbers and dial the numbers in circles. If nobody answers, the call just keeps 3 loops at most. At the meantime, the device will upload power cut off alarm data to the server. And it will send: Cut Power ! <Date Time:13-06-17 14 : 53 : 06>, http://maps.googIe.com/maps?q=N22576713,E1 13.916585

NOTE:

The SOS numbers should be preset, please refer to 5.1.

Low battery alarm

When the device is only working with battery, once the internal voltage of battery is less than 3.7V, device will send low battery alarm SMS to SOS number and alarm on platform. Low battery alarm SMS content example:”Attention!!!Battery is too low, please charge.” Which means the battery is too low, inform user charging it in time.

NOTE:
The SOS numbers should be preset, please refer to 5.1.

Vibration alarm

The vibration alarm function is off by default. To activate this function, please send the following command: SENALM, ON#
ACC OFF & in arming state If 5 times (times can be set) of vibration detected in 10 seconds, 1) ACC OFF in the following 30 seconds, the device will send vibration alarm. 2) ACC ON in within 30 seconds, no vibration alarm will be triggered.

NOTE:

  1. The SOS numbers should be
  2. Send “SENALM, OFF#” to turn off the vibration alarm if don’t

Oil cut-off

  1. via plat form
    Send oil cut-off command on platform. To make sure the security of vehicle, tracker can only indicate to cut off oilwhen GPS is in valid position status, and the speed is less than 20KM/H or in static. Platform account password is needed when sending oil cut off command.

  2. Via SMS
    Firstly, you should set a center number. Please refer to 5.4. Only center number can send the command to the device to cut off and restore oil.
    The format is: RELAY,1#
    After the command is carried out, it will reply “Cut off the fuel supply: Success! Speed:0 Km/h”. If the command didn’t carry out, it will reply the reason about fail to carry out.
    NOTE:
    To ensure the safety of the driver and the car this command is valid only under two conditions: the GPS is located; the speed is less than 20km/h.

Restoring Oil

  1. Via platform
    When the alarm is off, sending recover oil commands manually. Device will restore oil supplying, and vehicle will work normally again.
    Platform account password is needed when sending oil cut off command.

  2. Via SMS

Only center number can send the command to the device to restore oil. The format is: RELAY,0# After the command is carried out, it will receive “Restore fuel supply: Success!”

Over Speed Alarm

When the car is moving over a limited speed in average in a limited time period, then the device will send over speed alarm SMS to user. To turn on the over speed function, please send below SMS command: SPEED,ON,Time,Limited speed,way of alarm# Time range (Second) : 5-600s (default as 20s). Limited speed range (km/h) : 1-255, default: 50. Way of alarm: 0, GPRS only; 1, SMS+GPRS; default: 1. Example: SPEED,ON,10,120,1# Means when the car is moving over 50km/h in average in 10 seconds, the device will send over speed alarm to user.

Restore to factory setting

SMS command format: “FACTORYS” to set all parameter to default factory value. Once received “OK! The terminal will restart after 60s!”, it succeeds.

Reboot device

When there is something wrong with the link of GPRS, e.g., the parameter setting of the device is correct, but you can’t track the car on the platform. At this moment you can send a command to the device to reboot the device. The format is: RESET# After receiving this command, the device will reboot after 20 seconds

Platform

Login www.tracksolid.com by account name and password. The function on the GPS platform can be realized as follows:

  • Real-time Tracking
  • Report and Statistics
  • Online Configuration

Troubleshooting

If you are having trouble with your device, try these troubleshooting procedures before contacting a service professional

Problems| Causes|
---|---|---
Red LED does not work when power connected| The fuse blows| Replace the fuse
Fail to connect network| Wrong installation of SIM card| Check SIM card installation ( • 4.1 Install SIM card)
Filth on the SIM card iron surface.| Clean it
Useless SIM| Contact internet service provider
Improper installation| Check installation of device( ¥• 4.4 Install the device)
Beynd GSM service area| Use it in effective GSM service offer area
Bad signal| Try again in a better

signal area

Fail to charge| The voltage is unsuitable| Connect with power with suitable voltage
Improper connection| Check connection with charger

This device is only for use with 12V. 24V, 36V, 48V. or 72V vehicles. One side of the device is marked THIS SIDE TOWARDS SKY”, place the unit upside down will result in connection issues. Avoid placing the device somewhere that metal will be covering it up.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals