POOL BLASTER Spa Vac Recharge Instruction Manual
- June 3, 2024
- POOL BLASTER
Table of Contents
Instruction Manual
Cordless Vacuum
https://qr.watertechcorp.com/bcWX0S
Spa Vac Recharge
READ AND SAVE THESE INSTRUCTIONS
WARNING: Read carefully and understand all safety warnings before
operating. Failureto do so may result in serious personal injury.
IMPORTANT SAFETY INSTRUCTIONS
SAVE THESE INSTRUCTION S
WARNINGS AND USAGE INFORMATION
WARNINGS
-
Read carefully and understand all safety warnings before using this appliance.
-
Do not attempt to operate if the cleaner or USB charging cord appear to be damaged in any way.
-
All cautions and warnings on the equipment should be noted.
-
Never allow children to operate this product. This is NOT a toy. Children should be supervised to ensure they do not play with this product.
-
Keep the cleaner and its accessories out of reach of children.
-
This cleaner is not intended for use by persons with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning the use of the appliance by a person responsible for their safety.
-
Charge indoor only. Do not use or store the USB charging cord outdoors. Charge your cleaner in a clean, dry place and only with the USB charging cord provided. Do not use a USB charging cord supplied with any other appliance.
-
The warnings, cautions, and instruction discussed in this instruction manual cannot cover all possible conditions or situations that could occur. It must be understood, the operator should always exercise intensive caution and common sense when utilizing the cleaner.
-
Risk of electric shock. Do not expose to liquid, vapor or rain. Store cleaner in a clean dry place. Do not store in direct sunlight or expose to extreme temperatures.
-
Do not plug or unplug the USB charging cord into a power source or the appliance with wet hands.
-
Do not operate this cleaner in the presence of flammable or combustible liquids.
-
Never service the cleaner while the unit is on or connected to the USB charging cord.
-
Installation work and electrical wiring must be done by qualified person(s) in accordance with all applicable codes and standards, including fire-rated construction.
-
Use only the USB charging cord supplied with the cleaner. Never carry the USB charging cord by its cord or disconnect it from an outlet by pulling on the cord.
-
For pluggable equipment, the socket-outlet shall be installed near the equipment and shall be easily accessible.
-
Keep proper footing and balance at all times when using the cleaner. Do not overreach.
-
Please disconnect this equipment from AC outlet before cleaning. Don’t use liquid or sprayed detergent for cleaning. Use moisture sheet or cloth for cleaning.
-
This cleaner contains rechargeable batteries. Do not incinerate the battery as it will explode at high temperatures. Always dispose of batteries in accordance with local law.
-
Leaks from a battery may occur under extreme conditions. If battery liquid gets on the skin, wash immediately with water. If it gets in your eyes, immediately flush your eyes with a mild solution of baking soda and water, and seek medical attention.
-
Keep hair, loose fitting clothing and all body parts away from openings and moving parts of this cleaner.
DANGER!
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, CAREFULLY FOLLOW THESE INSTRUCTIONS. When using electrical products, read, understand and follow all the instructions stated in this manual.
WARNING!
DROWNING HAZARD. This device produces suction. Risk of entrapment present. DO NOT use when bathers are present. Never permit children to use this product. Never permit persons who cannot swim to use this product to prevent the chance of drowning.
DANGER!
DO NOT ALLOW WATER OR OTHER HIGHLY CONDUCTIVE FLUIDS TO CONTACT THE USB CHARGING CORD OR CHARGING JACK PRIOR TO OR WHILE CHARGING THE APPLIANCE. Pool water is highly corrosive and will cause damage to the USB charging cord or charging jack and can cause short-circuit
resulting in smoke, fire and/or serious personal injury. Make sure all surfaces of the USB charging cord and charging jack are dry and no water is present before charging the appliance.
WARNING!
CHARGING THE UNIT REQUIRES A USB CHARGING ADAPTER (NOT INCLUDED) Use charging adapter with a safety output of 5.0V DC and 1.0A. For EU, a CE-certificated adapter shall be used. For U.S.A. and Canada, a limited power source (LPS) or Class 2 type adapter certified by North American standards shall be used. Refer to the instruction manual of USB charging adapter (not included) for instructions concerning safety and operation.
USAGE INFORMATION -
Use this product only for its intended purpose as described in this manual. Use only Water Tech accessories and filters.
-
This product is not intended for commercial use.
-
If the equipment is not in use for long time, disconnect the equipment from mains to avoid being damaged by transient over-voltage.
-
Never leave your cleaner in water when it is “OFF” or when it has run out of power.
-
Do not use your cleaner for pool openings; the cleaner is designed for routine maintenance of your pool or spa.
-
The cleaner is designed for underwater use in swimming pools or spas only. It is not an all purpose vacuum cleaner.
-
Submerge the cleaner in water immediately after turning the unit “ON” to prevent damage to the seal on the motor shaft. Failure to do so will shorten the life of the water seal and / or void the warranty.
-
Avoid picking up sharp objects as they may damage the filter. Keep all openings on the cleaner free of debris which may reduce water flow.
-
Do not place the cleaner or the USB charging cord on or near hot surfaces.
-
For best results use the USB charging cord in locations where temperatures are between 50˚ F / 10˚C and 100˚ F / 37.7˚ C.
-
For connection to a supply not in the U.S.A., use an attachment plug adapter of the proper configuration for the power outlet.
SAFETY AND USAGE SYMBOLS
The following symbols and meanings are intended to explain the levels of
risk associated with this product:
| SYMBOL | SIGNAL | MEANING |
|---|---|---|
| **** | WARNING! | Indicates a hazardous situation, which, if not avoided, |
could result in death or serious injury.
**| DANGER!| Indicates a hazardous situation, which, if not avoided,
could result in death or serious injury.
| CAUTION!**| Indicates a hazardous situation, that, if not avoided, may
result in minor or moderate injury.
The following symbols and meanings are intended help you operate the product better and safer. Please study them and learn their meanings.
| SYMBOL | NAME | EXPLANATION |
|---|---|---|
| SAFETY ALERT | Indicates a potential personal injury hazard. Basic |
precautions should always be followed when seeing this symbol.
| DO NOT GET WET| Indicates by NO MEANS water should touch the indicated part
with this symbol. If not avoided, may result in minor or moderate injury.
| CHARGE FOR
4 FULL HOURS| Indicates to charge product for the 4 complete hours.
| BATTERY
RECYCLE| Recycle batteries in accordance to local law.
| DISPOSAL| Dispose any unwanted product in accordance to local law.
| CE| European Conformity.
| RoHS| Restriction of Hazardous Substances Compliance.
Product Breakdown
Charging the battery:
It requires USB charging adapter (not included) with the following
specifications:
Input……………………………………………………………………………..100-240V AC, 50-60Hz
Output………………………………………………………………………………….5.0V DC and 1.0A
Battery Tech Data………………………………………………..3.7V, 2200mAH, 8.14Wh Li-Ion
Operation
Charge Temperature…………………..Maximum 100°F, (37.7°C) Minimum 50°F, (10°C)
Water temperature range…………………..Maximum 96°F, (35°C) Minimum 40°F, (5°C)
Operation Depth…………………………Maximum 12 ft. (3.5 m), Minimum 10 in. (0.25 m)
- Make sure the charging receptacle on the product is dry before any charging.
- A full charge takes up to 4 hours. For EU Market, a CE-certificated USB charging adapter shall be used.
For US and Canada market, a Class 2 type adapter certificated by North America
standards.
Industry Canada Regulatory Information
CAN ICES-3 (B)/NMB-3 (B)
Avis d’Industrie Canada
CAN ICES-3 (B)/NMB-3 (B)
FCC Compliance
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to
provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency
energy and, if not used
in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular
installation, If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is
encouraged to try and correct the interference by one or more of the following
measures:
- Reorient or relocated the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different than that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
NOTE: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
| 
---|---
LIMITED WARRANTY
Water Tech Corp (“WT”) warrants this product, including supplied accessories
against defects in material or workmanship for the time periods as set forth
below. Pursuant to this Limited Warranty WT will, at its option (i) repair the
product to the original specifications or (ii) replace the product with a new
or refurbished product. In the event of a defect, these are your exclusive
remedies. For purposes of this Limited Warranty, “refurbished,” means a
product or part that has been returned to its original specifications.
All Pool Blaster Battery Powered Pool & Spa Vacuums. For a period of one (1)
year from the original date of purchase of the product, WT will, at its
option, repair or replace with new or refurbished product or parts, any
product or parts determined to be defective.
Accessories. Included accessories are covered by this Limited Warranty for a
period of (90) days from the original date of purchase of the product.
Instructions. Please retain the original box and internal packaging materials.
To obtain warranty service, you must comply with the following requisite
instructions:
- Visit Water Tech Corp’s Customer Support Department via web at www.wtrma.com. You will be guided through the correct process on how to obtain the required RMA# (Return Merchandise Authorization Number.) All customers must obtain an RMA number before any product will be accepted for warranty service. If you need additional assistance please contact us by telephone: (732-967-9888) or email: [email protected].
- Package the unit and the WT battery charger only ( if the unit requires a WT charger ) properly and securely in the original box.
- Attach your RMA number and Bar-Code you received from the website to the outside of the package. If you could not print the RMA number and barcode from the website you must write your RMA number in thick black indelible marker on two sides of the box.
- Send the package by USPS or express courier of choice to: Water Tech Corp, 10 lvin Court, East Brunswick, New Jersey 08816; (WT suggests you insure the contents of your package.) WT is not responsible for lost, stolen or damaged property in transit to WT.
Repair/Replacement Warranty. This Limited Warranty shall apply to any repair,
replacement part or replacement product for the remainder of the original
Limited Warranty period or for ninety (90) days, whichever is longer. Any
parts or products replaced shall become the property of WT.
This Limited Warranty covers only product issues caused by defects in material
or workmanship during ordinary consumer use; it does not cover product issues
caused by any other reasons, including but not limited to product issues
caused by commercial use, acts of God, misuse, abuse, limitations in
technology, or modification of or to any part of the WT product. This Limited
Warranty does not cover WT products sold AS IS or WITH ALL FAULTS or
consumables (such as batteries). This Limited Warranty is invalid if the
factory-applied serial number has been altered or removed from the product.
This Limited Warranty is valid only in the United States and Canada.
EXPRESS LIMITATION: THIS LIMITED WARRANTY ONLY APPLIES IF THE PRODUCT WAS
PURCHASED FROM AN AUTHORIZED WATER TECH DEALER. THIS WARRANTY IS NOT
TRANSFERABLE
LIMITATION ON DAMAGES. WT WILL NOT BE LIABLE FOR ANY INCIDENTAL OR
CONSEQUENTIAL DAMAGES FOR BREACH OF EXPRESS OR IMPLIED WARRANTY ON THIS
PRODUCT.
DURATION OF IMPLIED WARRANTIES. EXCEPT TO THE EXTENT PROHIBITED BY APPLICABLE
LAW, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR
PURPOSE ON THIS PRODUCT IS LIMITED IN DURATION OF THIS WARRANTY.
Some states do not allow the exclusion or limitation of incidental or
consequential damages, or allow limitations or how long an implied warranty
lasts, so the above limitations or exclusions may not apply to you. This
Limited Warranty gives you specific legal rights and you may have other
rights, which vary from state to state.
| P10XAP | 1. Vacuum Head |
|---|
2. Filter Bag
3. Power Head
P14X003LI| 4. Battery Chamber
---|---
P15X4PC| 5. Pool Pole (Set of 4)
1S-CBL-01SQ| 6. USB Charging Cable
A Charging Your Cleaner
Initial Charge 4 Hours
Recharging (After Complete Discharge) 4 Hours
Maximum charging time should not exceed 24 Hours
B Closing the Battery Chamber
C Inserting the Filter Bag
D Attaching the Pool Pole
E Turning the unit ON / OFF
F Maintenance
Cleaning the Filter Bag
- You should remove and clean the Filter Bag following each use (Figure F.1).
- Don’t scrub the bag against itself while rinsing it.
Long Term Storage
- Always clean the Head Cover and Filter Bag before storing.
- Always store and charge your cleaner in a cool, dry indoor shelter.
- Recharge the cleaner indoors for 4 hours after each month of inactivity.
- Never leave your USB charging cord connected to the cleaner for more than 24 hours.
End of Life Disposal / Recycling Directive
Environmental Program(s), WEEE European Directive
Environmental Recycling Programs USA
Help protect the environment.
(Refer to pages 22-23 for proper battery disposal instructions)
END OF LIFE BATTERY DISPOSAL
The maintenance free, Lithium Ion battery in your Pool Blaster must be
properly disposed of in accordance to State and local law.
To confirm if recycling is required; contact your local authority for
information.
WARNING!
• Never attempt to disassemble a battery pack.
-
Remove all personal items such as rings, bracelets, necklaces and watches when unwiring a pack from the vacuum unit.
-
A battery can produce a short circuit current high enough to weld a ring (or like item) to metal causing a severe burn.
-
Wear complete eye protection, gloves and protective clothing when removing the battery pack.
-
Take care not to touch wires together or allow them to contact any metal items, which would cause sparking and/or short circuit the battery.
-
Never smoke or allow a spark or flame in the vicinity of the battery or the cleaner. Batteries can generate gases which could possibly ignite.
-
Do not expose to fire or intense heat as this may result in an explosion.
CAUTION!
• If a battery leak develops, avoid contact with the leaking acid and place the damaged battery in a plastic bag. -
If acid comes in contact with skin and clothing, wash immediately with plenty of soap and water.
-
If acid comes in contact with eyes, immediately flood eye with running cool water for at least 15 minutes. Get medical attention immediately.
How to remove the battery
• Recommended tools (not included): Philips screwdriver, wire-cutters,
electrical tape.
- Detach the battery chamber from the power head.
- Using the Philips screw driver, unfasten the 2 screws on top of the motor-box.
- Pull the battery out shown in image three.
- Using the wire-cutters, cut the wires as shown in image four. Do not cut both wires at the same time.
- Wrap the wires with electrical tape. Dispose according to local law.
……………………
This page has been left blank intentionally.
10 Alvin Ct., Suite 111
East Brunswick, NJ 08816 – USA
Tel: 732-967-9888 US, Canada &
International
Fax: 732-967-0070 US & International
www.WaterTechCorp.com
Register at
www.watertechcorp.com/register
For service and parts, call the number above