Avilo H564i Wireless Bicycle Computer User Manual
- June 7, 2024
- Avilo
Table of Contents
Wireless Bicycle Computer
Thank you for purchasing the Wireless Bicycle Computer. We hope you will be
satisfied with your purchase. Note: A slight rattle sound in the product is
normal. It is part of the design of wireless automatic functions.
What’s included
I Computer
I Sensor Transmitter
1 Pad bracket
4 Cable ties
I CR2032 battery
I • Magnet I Rubber band
1 Instruction sheet
Note:
When attaching the sensor transmitter, battery cover, and computer mounting
holder, do not tear off the shim especially the shim on the back of the
computer battery cover. It is a part of the product and should not be torn
off.
Installation
Computer Battery Installation
Remove the battery cover from the bottom of the computer by using a flat blade
screwdriver, install one CR2032 battery with the positive (+) pole facing the
battery cover and replace the cover. Should the LCD show irregular figures,
take out the battery and reinstall it. ‘2060’ appears on the screen means
installation correctly.
Sensor Transmitter Battery Installation
Remove the battery cover from the bottom of the computer by using a flat blade
screwdriver, install one 2032 battery with the positive (+) pole facing the
battery cover and replace the cover. Should the LCD show irregular figures,
take out the battery and re-install it.
Sensor Transmitter Installation
Attach the sensor transmitter to the left fork blade, the distance between the computer and the sensor can not exceed 60cm, the closer the better. Using the shims to adjust the diameter, and using the cable ties(shown above) to tie it with the fork(once diameter, please tear off the yellow paper on the tape for fixing). Position the sensor transmitter and magnet as shows, make sure that the arc of the magnet intersects the alignment mark on the sensor transmitter with 1mm clearance.
Mounting Ring Instaiiations
Attach the mounting ring with the cable ties to the handlebar, adjust the
mounting Ring on the handlebar with the shims to hold its position.
Computer Installation
Attach the computer to the mounting shoe by sliding the unit until it snaps
firmly into its position. To remove it, press the button on it in the opposite
direction.
To check for proper speed function and sensor alignment, spin the front wheel
with a computer in speed mode. Adjust the position of the sensor and magnet
when there is no or weak reaction.
Setting of Parameters
Once you have set the wheel size parameter to ‘km/h or m/h, the rest of the
parameters will change automatically while your tire is running.
If you need to re-set the settings once the computer is working, press both
rights and left buttons at the same time for at least 5 seconds. The “2060”
code should appear and then you can re-set the wheel size. After this is done
you can then set up km/h or m/h.
Wheel Size Input
`2060′ appears on the screen when the battery has been installed, with one
figure flashing, choose the correct wheel circumference from the table below.
Press the RIGHT button to advance digits as needed and the LEFT button to
confirm and advance. (The circumference ranges Omm-9999nun), press the LEFT
button to enter KM/M mode.
TIRE SIZE | CIR | TIRE SIZE | CIR | TIRE SIZE | CIR |
---|---|---|---|---|---|
29″x2.3″ | 2326 | 27″x 1(630) | 2145 | 24″x 1(520)” | 1753 |
29″x2.2″ | 2298 | 650c x 38Amm | 2125 | 24″x 2.125″ | 1965 |
29″x2.I” | 2288 | 650c x 38Bmm | 2105 | 24″x 2.00″ | 1925 |
700c x 47mm | 2268 | 650c x 25Cmm | 1952 | 24″ x 1.9″ | 1910 |
700c x 45mm | 2242 | 650c x 23mm | 1944 | 24″x 1.75″ | 1890 |
700c x 44mm | 2235 | 650c x 20mm | 1938 | 22″x 1-1/2″ | 1785 |
700c x 42mm | 2224 | 650cTubulari | 1920 | 22″x 1-3/8″ | 1770 |
700c x 40mm | 2200 | 26″x 1-1/2″ | 2100 | 20″ x 1-3/8″ | 1615 |
700c x 38mm | 2180 | 26″x 1-3/8″ | 2068 | 20″ x 1-1/8″ | 1545 |
700cTubulari | 2130 | 26″x 1-1/8″ | 1970 | 20″ x 1.95″ | 1565 |
700c x 35mm | 2168 | 26″x 3.00″ | 2170 | 20″x 1.35″ | 1460 |
700c x 32mm | 2155 | 26″x 2.35″ | 2083 | 20″ x 1.25″ | 1450 |
700c x 30mm | 2146 | 26″ x 2.25″ | 2070 | 18″ x 1.75″ | 1350 |
700c x 28mm | 2136 | 26″ x 2.10″ | 2068 | 18″ x 1.50″ | 1340 |
700c x 25mm | 2105 | 26″ x 2.0″ | 2062 | 17″ x 1-1/4″ | 1340 |
700c x 23mm | 2096 | 26″ x 1.95″ | 2050 | 16″ x 1-3/8″ | 1300 |
700c x 20mm | 2086 | 26″ x 1.90″ | 2045 | 16″ x 1-1/8 | 1290 |
700c x 19mm | 2080 | 26″x 1.75″ | 2023 | 16″ x 2.0″ | 1245 |
700c x 18mm | 2070 | 26″x 1.50″ | 2010 | 16″ x 1.95″ | 1240 |
27.5″x 2.25″ | 2182 | 26″x 140″ | 2005 | 16″ x 1.75″ | 1195 |
27.5″x 2.1″ | 2148 | 26″x 1.25″ | 1950 | 16″ x 1.50″ | 1185 |
27.5″x 1.50″ | 2079 | 26″x 1.0″ | 1913 | 14″ x 1.75″ | 1055 |
27″x 1-3/8″ | 2169 | 24″x 1-1/4″ | 1905 | 14″ x 1.50″ | 1020 |
27″x 1-1/4″ | 2161 | 24″x 1-1/8″ | 1795 | 12″ x 1.95″ | 940 |
27″x 1-1/8″ | 2155 | 24″x3/4″ | 1785 | 12″x 1.75″ | 935 |
Setting ( km/h ) / ( m/h )
Press the RIGHT button to choose km/h or m/h. Press the LEFT button to enter
CLOCK mode.
CLK Mode(12H/24H)
In CLOCK Mode, press the LEFT button for 3 seconds to enter 12/24H selection.
Re-press the LEFT button for 12/24 exchanging. Press the RIGHT button to enter
Hour setting mode, when the figure indicating HOUR start to flash, press the
LEFT button to adjust it. Continue to press the RIGHT button to enter Minute
setting mode, when the figure indicating MINUTE start to flash, press the LEFT
button to adjust it and the RIGHT button to confirm, press the RIGHT button
again to ODO mode.
** Setting the Last Valu of Odometer
In ODO mode, press the LEFT button for 2 seconds to set the ODO value, its
initial value is 0000.0. when one figure flashing, press the RIGHT button to
adjust it and the LEFT button to confirm it and start to set the next figure.
(After the battery has been re-installed, the latest value can be inputted
according to the value before pre-installation of the battery. )
Reset of Mlileatie Parameter
In ODO mode, press and hold both RIGHT and LEFT buttons simultaneously for 3
seconds to clear the tire circumference and (km/m) setting, The user needs to
reset the tire circumference and (km/m), the original ODO value, and CLOCK
will remain unaffected.
Speedometer
Speed is shown all the time on the screen, its maximum reading is
99.9km/h(m/h), and it’s accurate to +/- 0.1km/h (in/h)•
Speed Computer**
During riding, ‘ + ‘ and ‘ -‘ indicates the current speed is higher or lower
than the average speed(AVS).
Odometer
In ODO mode, the total distance is -. I indicated on the screen, its mileage
range is 0.001 — 99999km(m). the _ • display will be back to 0 when the value
exceeds its maximum limit, press the RIGHT button to enter DST mode..
Trip Distance (DST)
In DST mode, the distance for one trip is indicated on the bottom line. DST
ranges from 0.001 –9999km(m), when the value exceeds the range limit, it
-restarts from 0 automatically. Both the time and the distance records will be
cleared when the time of one trip exceeds the range limits.
Press the LEFT button for 5 seconds to clear the records of DST, MXS, AVS, and
TM.
Press the RIGHT button to enter MXS mode.
Maximum S wed (MXS)
In MXS mode, maximum speed is indicated on the bottom line. Press the LEFT
button for 5 seconds to clear the records of MXS, DST, AVS, and TM. Press the
RIGHT button to enter AVS mode.
Average Speed
In AVS mode, the average speed is indicated on the bottom line. Press the LEFT
button for 5 seconds to clear the records of AVS, DST, MXS, and TM. Press the
RIGHT button to enter TM mode.
Trip Time
In TM mode, trip time is indicated on the bottom line.TM ranges 0 :00 :00
99 :59 :59. It will be back to 0 when the value exceeds the limits.
Press the LEFT button for 5 seconds to clear the records of TM, DST, MXS, and
AVS. Press the RIGHT button to enter SCAN mode.
SCAN
In Scan mode, DST, MXS, AVS, and TM • mode are indicated in tum every 4
seconds. Press the RIGHT button to enter CLOCK Mode.
Sleep Mode
If no signal has been inputted for 300 seconds, the computer will enter into
Sleep Mode, and the CLK value remains. It will turn back to the former model
with all the data collected when any signal is inputted or any button is
pressed.
FREEZE FRAME MEMORY
Press the LEFT button at any time will enter into freeze-frame memory mode.
Flashing TM data will appear on the screen. Press the RIGHT button to view the
records of DST, MXS, AVS, and TM. Press the LEFT button to end it.
Button Instruction
Press the RIGHT button to choose any mode below: ODO, DST, MXS, AVS, TM, SCAN (DST. MXS, AVS. TM), and CLOCK. It’s unnecessary to press the LEFT button except to choose the Freeze frame Memory mode. In Freeze Frame Memory mode, press the RIGHT button, several data will display, re-press the LEFT button to turn back to other modes.
Malfunctions and Problems
Malfunctions | Problems |
---|---|
No speedometer | Improper magnet/sensor alignment Distance between computer and |
sensor transmitter exceed 60cm
The low battery voltage of the sensor transmitter or computer.
A short distance of the transmitter or no receiving| Lower battery voltage,
need to change for a new one.
Display Abnormal figures| Too much Electromagnetic interference around
An inaccurate value is indicated| Improper input, such as wheel circumference.
Slow display response| Temperature exceeds operating limits(Ot —55 C).
Black display| Temperature too high, or put in direct sunlight for too long
time. Need to take back to shadow place for a period.
Weak display| Poor battery contact or dead battery
The display shows irregular figures| Take out the battery and re-install it
after 10 seconds.
Sensor without reaction| Put off the insulation film of the sensor transmitter
Back Light
The backlight is only on when you press any button from 6 pm to 7 am.
Product Code: J192101
Made in China for S&S Enterprises Ltd. 26 Perivale Park Middlesex UB6 7RL
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>