BOSE T4S/T8S ToneMatch Mixer User Guide

T4S/T8S ToneMatch®

Mixer

Quick Start Guide

Important Safety Instructions

Please read and keep all safety and use instructions.

1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with a dry cloth.
7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
8. Protect the power cord from being walked on or pinched, particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.
9. Only use attachments/accessories specified by the manufacturer.
10.   Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.
11. Unplug this apparatus during lightning storms or when unused for long periods of time.
12. Refer all servicing to qualified personnel. Servicing is required when the apparatus has been damaged in any way such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

WARNINGS/CAUTIONS:

This product contains magnetic material. Consult your physician on whether this might affect you implantable medical device.

• This product is not intended for installation or use in indoor water facility areas (including, without limitation, indoor pools, indoor water parks, hot tub rooms, saunas, steam rooms and indoor skating rinks).
• To reduce the risk of fire or electrical shock, do NOT expose this product to rain, liquids or moisture. Not applicable for products rated IPX4-9.
• Keep the product away from fire and heat sources. Do NOT place naked flame sources, such as lighted candles, on or near the product.
• Do NOT make unauthorized alterations to this product.
• Do NOT use a power inverter with this product.
• Do NOT use in vehicles or boats.
• Use this product only with the power supply provided.
• Do NOT place or install the bracket or product near any heat sources, such as fireplaces, radiators, heat registers or other apparatus (including amplifiers) that produce heat.
• Do not use the ToneMatch® T4S/T8S mixer with a tripod/stand that is unstable. The mixer is only designed for use on a 1/4″ screw (6,3 mm), and the tripod/stand must be capable of supporting a device with a minimum weight of 1.9 kg (4.1 lbs) and an overall size of 214 x 311 x 83 mm (8.4 x 12.25 x 3.25 inches). Using a tripod/ stand that is not designed to support the size and mass of the T4S/T8S mixer may lead to an unstable and hazardous condition that could result in injury.
• Contains small parts which may be a choking hazard. Not suitable for children under age 3.

NOTES:

• The speaker wire and interconnect cables included with this system are not approved for in-wall installation. Please check your local building codes for the correct type of wire and cable required for in-wall installation.
• Where the mains plug or an appliance coupler is used as the disconnect device, the disconnect device shall remain readily operable.
• Due to ventilation requirements, Bose does not recommend placing the product in a confined space such as in a wall cavity or in an enclosed cabinet.

Regulatory Information

This device complies with part 15 of the FCC Rules and with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Bose Corporation hereby declares that this product is in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU and all other applicable EU directive requirements. The complete declaration of conformity can be found at: www.Bose.com/compliance.

Information About Products That Generate Electrical Noise (FCC Compliance Notice for US)

Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at one’s own expense.
Changes or modifications not expressly approved by Bose Corporation could void the user’s authority to operate this equipment.

Shielded cables are required to maintain regulatory compliance.

This product complies with the Canadian ICES-003 Class A specifications. CAN ICES-3(A)/NMB-3(A)

This product meets all EN55103-2 immunity requirements for E2 electromagnetic environment.

Names and Contents of Toxic or Hazardous Substances and Elements

X

| 0| 0| 0| 0|

0

Metal parts|

X

| 0| 0| 0| 0|

0

Plastic parts|

0

| 0| 0| 0| 0|

0

Speakers|

X

| 0| 0| 0| 0|

0

Cables|

X

| 0| 0| 0| 0|

0

This table is prepared in accordance with the provisions of SJ/T 11364.
0: Indicates that this toxic or hazardous substance contained in all of the homogenous materials for this part is below the limit requirement of GB/T 26572.
X: Indicates that this toxic or hazardous substance contained in at least one of the homogenous materials used for this part is above the limit requirement of GB/T 26572.

This symbol means the product must not be discarded as household waste, and should be delivered to an appropriate collection facility for recycling. Proper disposal and recycling helps protect natural resources, human health, and the environment. For more information on disposal and recycling of this product, contact your local municipality, disposal service, or the shop where you bought this product.

For China:

  Only suitable for use at areas with altitude less than 2000 m.

Provided by DCE Safety

Introduction

Product Overview

Take control of your music with T4S and T8S ToneMatch® mixers, compact 4 and 8 channel interfaces designed for performers. Engineered with powerful DSP engines and intuitive user controls, they offer studio-quality EQ, dynamics and effects processing. Sound great with integrated Bose® ToneMatch® processing and zEQ, especially when connected to a Bose L1 or F1 system for full end-to-end tonal control. Play confidently on stage with these rugged ToneMatch mixers using tactile controls, easy-to-read LED displays and scene recall. ToneMatch mixers, the ultimate on-stage companions for performing artists.

Product Features

Powerful Audio Processing

• Updated, studio-quality effects with advanced digital audio processing
• Effects include compressor, limiter, de-esser, noise gate, chorus, flanger, phaser, tremolo, delay, and reverb
• Bose® ToneMatch® processing for natural-sounding vocals and instruments
• zEQ focuses the sound of ToneMatch presets for effective adjustments on the fly
• Independent ToneMatch, EQ, dynamics and effects per channel
• Dedicated reverb for Aux sends, and a global shared reverb for use across all channels
• Master output EQ helps compensate for venue acoustics
• Full end-to-end tonal optimization when used with Bose L1 and F1 systems

Seamless Live Control

• Tactile controls and indicators designed for live on-stage use by musicians and DJs
• Fast-learning user interface
• Built-in tap tempo delay, chromatic tuner, and recallable scenes
• LED display and illuminated controls are easy to read and use, even on dimly-lit stages

High-Density Connectivity

• Unprecedented connectivity and control in a small digital stereo mixer
• Four (T4S) or eight (T8S) high-quality audio preamps with XLR-combo jacks for microphones or instruments, and switchable phantom power
• Two Aux inputs for additional sources two (T4S) or four (T8S) Aux sends
• USB-A and -B for USB drive playback or PC/Mac interfacing
• ToneMatch outputs for digital audio and power (T4S only)
• Balanced ¼” TRS and XLR (T8S only) stereo outputs
• Independent headphone output

Convenient Gig-Ready Features

• Rugged enclosure with a protective magnetic cover to protect controls and connectors
• Includes a ToneMatch cable for connecting to a Bose L1 Model II or L1 Model 1S system for digital audio and power (T4S), or includes a universal power supply (T8S)
• Bottom insert allows you to use standard camera mounting accessories to keep your ToneMatch mixer within reach

Unpacking

See the following table for what your mixer carton will include:

T4S|    

T4S ToneMatch mixer and cover

|

ToneMatch Cable

---|---|---
T8S|

T8S ToneMatch mixer and cover

| ToneMatch power supply

Note: Refer to the complete owner’s guide (online at www.Bose.com) for more information about operation, factory settings, and care and maintenance.

Control and Connection Panels

T4S ToneMatch® Mixer

Control Panel

Figure 1. T4S Control Panel

(1) INPUT SIGNAL/CLIP LEDs (1–4): Displays the input signal status in color:
Green: Indicates the presence of an input signal
Red: Indicates input source clipping
(2) TRIM CONTROLS (1–4): Adjusts the input sensitivity for the respective channel.
(3) DISPLAY: Provides function menus and system information.
(4) EDITING CONTROLS: These three rotary/push-button controls allow you to select or adjust items/values appearing on the display.
(5) CH EDIT BUTTONS (1–4): Selects the channel you want to modify.
(6) FX MUTE BUTTONS (1–4): Bypasses the Mod, Delay, and Reverb effects on the selected channel.
(7) VOLUME CONTROLS (1–4): Adjusts the volume level for the respective channel.
(8) MUTE BUTTONS (1–4): Silences the audio output for the respective channel.
(9) MASTER VOLUME CONTROL: Adjusts the overall output level.
(10) HEADPHONE VOLUME CONTROL: Adjusts the volume level of the headphone output.
(11) ROTARY SELECTOR: Allows access to both global and channel-related parameters, which are adjusted using the editing controls.
(12) PHANTOM POWER SWITCH: Applies +48V power to Input Channels 1–4. A red LED indicates that phantom power is on.

CAUTION : Set the Master volume control to its minimum position before using the phantom power switch or powering on/off any microphones that use phantom power.

(13) HEADPHONE JACK: For use with headphones only, with a minimum impedance of 24Ω.

Connection Panel

Figure 2. T4S Connection Panel

(1) POWER SWITCH: Turns the mixer on or off.
(2) USB 2.0 TYPE-B: A USB interface that allows you to connect the mixer to your computer.
(3) USB 2.0 TYPE-A: A USB interface that allows you to stream audio from your flash drive.
(4) ANALOG L/R OUTPUT: Main analog output. Accepts ¼-inch TRS balanced or TS unbalanced cables.
(5) AUX OUTPUT: Two user-definable analog outputs. Can be configured for a pre-fader, post-EQ, and effects, or post-fader output. Accepts ¼-inch TRS balanced cables.
(6) AUX IN: Analog Input Channels 5/6. Accepts ¼-inch TRS balanced or TS unbalanced cables for line-level inputs. Can be used for stereo input signals.
(7) INPUTS 1–4: Analog Input Channels 1–4. Accepts XLR balanced cables for microphones or ¼-inch TRS balanced or TS unbalanced cables for high- impedance inputs, such as guitars.
(8) DIGITAL MAIN OUTPUT L: Connect digitally in stereo to two L1® Model 1S/II systems.
Note: Only used in stereo with Digital Main Output R.
(9) POWER PORT/DIGITAL MAIN OUTPUT R: A digital output used by the L1 Model 1S/II system. Delivers power to the T4S mixer from the L1 Model 1S/II power stand. Can also deliver power from an AC outlet via a ToneMatch power supply (not included with the T4S). Accepts the included ToneMatch® cable.

CAUTION: Although the ToneMatch port accepts a standard RJ-45 connector, do NOT connect the T4S to a computer or phone network.

T8S ToneMatch® Mixer

Control Panel

Figure 3. T8S Control Panel

(1) INPUT SIGNAL/CLIP LEDs (1–8): Displays the input signal status in color:
Green: Indicates the presence of an input signal
Red: Indicates input source clipping
(2) TRIM CONTROLS (1–8): Adjusts the input sensitivity for the respective channel.
(3) DISPLAY: Provides function menus and system information.
(4) EDITING CONTROLS: These three rotary/push-button controls allow you to select or adjust items/values appearing on the display.
(5) CH EDIT BUTTONS (1–8): Selects the channel you want to modify.
(6) FX MUTE BUTTONS (1–8): Bypasses the Mod, Delay, and Reverb effects on the selected channel.
(7) VOLUME CONTROLS (1–8): Adjusts the volume level for the respective channel.
(8) MUTE BUTTONS (1–8): Silences the audio output for the respective channel.
(9) MASTER VOLUME CONTROL: Adjusts the overall output level.
(10) HEADPHONE VOLUME CONTROL: Adjust the volume level of the headphone output.
(11) STEREO OUTPUT METER: Allows you to visually measure your output level.
(12) ROTARY SELECTOR: Allows access to both global and channel-related parameters, which are adjusted using the editing controls.
(13) PHANTOM POWER SWITCH: Applies +48V power to Input Channels 1–8. A red LED indicates that phantom power is on.

CAUTION: Set the Master volume control to its minimum position before using the phantom power switch or powering on/off any microphones that use phantom power.

(14) HEADPHONE JACK: For use with headphones only, with a minimum impedance of 24 Ω.

Connection Panel

Figure 4. T8S Connection Panel

(1) POWER SWITCH: Turns the mixer on or off.
(2) USB 2.0 TYPE-B: A USB interface that allows you to connect the mixer to your computer.
(3) USB 2.0 TYPE-A: A USB interface that allows you to stream audio from your flash drive.
(4) ANALOG L/R OUTPUT: Main analog output. Accepts ¼-inch TRS balanced and TS unbalanced cables.
(5) AUX OUTPUT: Four user-definable analog outputs. Can be configured for a pre-fader, post-EQ, and effects, or post-fader output. Accepts ¼-inch TRS balanced or TS unbalanced cables.
(6) AUX IN: Analog Input Channels 9/10. Accepts ¼-inch TRS balanced or TS unbalanced cables for line-level inputs. Can be used for stereo input signals.
(7) INPUTS 1–8: Analog Input Channels 1–8. Accepts XLR balanced cables for microphones or ¼-inch TRS balanced or TS unbalanced cables for high- impedance inputs, such as guitars.
(8) XLR STEREO OUTPUT: Stereo analog output. Accepts XLR balanced cables for stereo output.
(9) DIGITAL POWER PORT: For use w/ ToneMatch power supply (see “Connecting the ToneMatch® Power Supply” on page 12).

Note: The T8S is NOT designed to connect digitally to the L1® Model 1S/II.

CAUTION: Although the ToneMatch port accepts a standard RJ-45 connector, do NOT connect the T8S to a computer or phone network.

System Setup

Removing/Attaching the Cover

The T4S/T8S ToneMatch® mixer comes out of the carton with a cover installed on the top panel. The cover is designed to protect the control panel while transporting or storing the mixer.

To remove the cover:

1. Place thumbs on notches on front of cover and slide cover forward.
2. Grab cover by the back and lift to remove it.

To attach the cover:

1. Slide cover over the mixer, from back to front.
2. The magnetized cover will engage on its own and secure itself to the mixer.

Figure 5. Removing and attaching the cover

Mounting Options

The T4S/T8S comes with a 1/4″ (6,3 mm) mounting screw insert. This enables it to be mounted onto a number of available products that include a 1/4″ (6,3 mm) mounting screw, including a camera tripod stand.

Mounting the T4S/T8S on a Camera Tripod Stand

1. Extend the camera tripod legs and secure at desired height.
2. Remove the bracket from the top of the camera tripod stand and secure the bracket to the bottom of the T4S/T8S with the screw. Make sure the small indentation on the T4S/T8S and the bump on the bracket are aligned. See Figure 6.
3. Secure the bracket with the T4S/T8S back onto the camera tripod stand. See Figure 8.

Figure 6. Securing bracket to T4S          Figure 7. Bracket attached to T4S

Figure 8. Mounting T4S to tripod stand using bracket

WARNING: Do not use the ToneMatch® T4S/T8S mixer with a tripod/stand that is unstable. The mixer is only designed for use on a 1/4″ screw (6,3 mm), and the tripod/stand must be capable of supporting a device with a minimum weight of 1.9 kg (4.1 lbs) and an overall size of 214 x 311 x 83 mm (8.4 x 12.25 x 3.25 inches). Using a tripod/stand that is not designed to support the size and mass of the T4S/T8S mixer may lead to an unstable and hazardous condition that could result in injury.

Connecting the T4S via Digital Connection

1. Make sure the L1 Model 1S/II and T4S are powered off and the T4S Master volume control is set to minimum.

2. Plug one end of the ToneMatch® cable into the Power port/Digital Main Output R on the T4S. Plug the other end of the ToneMatch cable into the ToneMatch port on the power stand.
   Note: To connect the T4S to two L1 Model 1S/II power stands, connect a second power stand to the Digital Main Output L port on the T4S using a ToneMatch cable.

3. Turn on the mixer and then turn on the L1 Model 1S/II power stand.

4. Connect your instruments and adjust levels. Refer to the complete owner’s guide at www.Bose.com for complete operation information.

Figure 9. Two L1 model II systems connected to a T4S via digital connection

Note: The T8S cannot be connected digitally and cannot be powered by the L1 Model 1S/II.

Connecting the T4S/T8S via Analog Connection

1. Make sure the device you are connecting to and the T4S/T8S are powered off and the T4S/T8S Master volume control is set to minimum.

2. Using XLR balanced cables, connect one or two devices to the XLR Stereo Outputs of your T8S (see Figure 10).
   Note: The T4S/T8S can be connected to a device via the Analog R Output port using a 1/4″ TRS cable (sold separately). Plug the other end of the TRS cable into the Analog Input port of the device. To connect the T4S/T8S to two devices, connect a second device to the Analog L Output port on the T4S/T8S using a 1/4″
   TRS cable.

3. Connect a ToneMatch® power supply to the Power port of the T4S/T8S and plug it into a live AC outlet. Refer to “Connecting the ToneMatch® Power Supply” on page 12.

4. Turn on the T4S/T8S mixer and then turn on the device.

5. Connect your instruments and adjust levels. Refer to the complete owner’s guide at www.Bose.com for complete operation information.

Figure 10. Two F1 systems connected to a T8S via analog connection

Connecting the ToneMatch® Power Supply

The ToneMatch power supply provides power for the T4S/T8S mixer.

1. Plug the power supply cable into the T4S/T8S Power port.
2. Plug one end of the AC power cord into the power supply.
3. Plug the other end of the power cord into a live AC power outlet.
4. Switch the T4S/T8S power switch to the ON position.

Note: Power supply included with T8S is required for operation of the T8S. Power supply is not included with the T4S and is not required for operation of the T4S.

Figure 11. Connecting T4S to power supply

Connecting the T4S/T8S to Your Computer

The T4S/T8S provides a USB port for connecting it to a computer. This allows you to download performance scenes to a computer or install system updates. Visit bosepro.link/tmu for details on updating your system.

When connected to a computer, you also can use the T4S/T8S as a general- purpose USB audio device for recording/playback.

Note: The T4S/T8S operates at 48 kHz/24-bit. When using the T4S/T8S with recording software, you may need to configure the software settings for 48 kHz/24-bit operation.
Note: Connecting the T4S/T8S to your computer requires a USB cable (Type A to Type B, not supplied).

1. Connect the mixer to a power source (ToneMatch® power supply for T4S/T8S or an L1 Model 1S/II for T4S only).
2. Plug one end of the USB cable into the mixer’s USB 2.0 Type-B port (Figure 12).
3. Plug the other end of the USB cable into a USB port on your computer.
4. Turn on the mixer.

Figure 12. T4S-to-USB connection

To computer USB port   

1. USB cable (Type A to Type B)
2. Power switch
3. ToneMatch port – To an L1 Model 1S/II system or an ToneMatch power supply

Connecting a Flash Drive to the T4S/T8S

Plug in a USB 2.0/3.0 flash drive loaded with WAV/MP3 files into the USB 2.0 Type-A port to playback audio tracks to your mixer.

Figure 13. Connecting a flash drive to the T4S

Additional Information

Refer to the complete owner’s guide (online at www.Bose.com) for more information about operation, factory settings, and care and maintenance. Contact Bose customer service for a printed copy.

Contact Information

Bose Corporation Headquarters: 1-877-230-5639

China Importer: Bose Electronics (Shanghai) Company Limited, Part C, Plant 9, No. 353 North Riying Road, China (Shanghai) Pilot Free Trade Zone

EU Importer: Bose Products B.V., Gorslaan 60, 1441 RG Purmerend, The Netherlands

Mexico Importer: Bose de México, S. de R.L. de C.V. , Paseo de las Palmas 405-204, Lomas de Chapultepec, 11000 México, D.F. For service or importer information, call +5255 (5202) 3545.

Taiwan Importer: Bose Taiwan Branch, 9F-A1, No. 10, Section 3, Minsheng East Road, Taipei City 104, Taiwan.
Phone Number: +886-2-2514 7676

See website for other countries.

Limited Warranty

Your product is covered by a limited warranty. Visit PRO.BOSE.COM for warranty details.

Date of Manufacture

The eighth digit in the serial number indicates the year of manufacture; “0” is 2010 or 2020.

©2020 Bose Corporation, All rights reserved.
Framingham, MA 01701-9168 USA
www.Bose.com
All trademarks are the property of their respective owners
AM806045 Rev. 01
March 2020

References

• Bose Professional
• Bose | Headphones, Earbuds, Speakers, Soundbars, & More

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>