SHURE MX415DUAL Dual-Capsule Gooseneck Microphone User Guide

June 7, 2024
Shure

logo

SHURE MX415DUAL Dual-Capsule Gooseneck Microphone

product

General Description
The Shure Microflex MX415DUAL dual-capsule gooseneck microphone features two electret condenser cartridges mounted in a single low-profile housing and two preamp-equipped outputs providing redundant audio for critical, multi-feed live sound and professional broadcast applications. With a 15” overall length, the MX415DUAL includes a flexible top gooseneck section for optimal placement, and includes all the mounting accessories required for installation into a lectern or tabletop configuration.

Features

  • Wide dynamic range and frequency response for accurate sound reproduction
  • Dual 1 cm cardioid Microflex interchangeable cartridges
  • Dual 5-foot cables exiting out bottom of mic, terminating in two TQG Connectors
  • Two external in-line preamps
  • Shock mount provides over 20 dB of isolation from surface vibration noise
  • RF filtering with CommShield technology

Interchangeable Cartridgesimage 1

Microflex microphones use interchangeable cartridges that allow you to choose the polar pattern for different installations.

Windscreen

  • Snap into place when fully seated.
  • To remove, grip under the wider sides of the foam and gently pull.
  • Provides “pop” protection of 30 dB for mesh and 40 dB for foam windscreens.image 2

Installation

Mount the microphone using a flange or shock mount.
Important : The dot on the microphone and TQG connector indicates which cartridge is connected to which connector. The included RK100PK phantom- powered preamps converts the TQG connector to an XLR output.

A13HDB Flange:
  1. Mark and drill 3 starter holes for the screws using the flange as a template.
  2. Secure the flange to the mounting surface with screws.
  3. Thread the microphone clip to the flange, then mount the microphone to the clip.
    Note : Use the extension tube with the microphone clip and flange if desired.
RPM640 Flange:
  1. Drill a 22 mm (7/8 in.) diameter hole in the mounting surface.
  2. Mark and drill 3 starter holes for the screws using the flange as a template.
  3. Insert the TQG connectors through the mounting flange.
  4. Slide the retaining ring over the bottom of the gooseneck base until is flush to the bottom of the flange, then press the ring firmly into place.
  5. Secure the flange to the mounting surface with screws.
A400SM Shock Mount:
  1. Drill a 44 mm (1-3/4 in.) diameter hole in the mounting surface.
  2. Mark and drill 3 starter holes for the screws using the shock mount as a template.
  3. Secure the shock mount to the mounting surface with screws.
  4. Insert the TQG connectors through the hole, then insert the microphone base.

image 3

Dimensionsimage 4

Accessories

Mic Swivel Adapter A57F
Extension Tube A26X
Cast Mounting Flange A13HDB
Locking Mounting Flange RPM640
Shock Mount A400SM
Inline Preamps (2) RK100PK
Preamp Mounting Plates (2) RPM40PREMNT
Retained Foam Windscreen RK415DWS
Veraflex Windscreen A415DGWS
Storage Pouch 95E2313

Specifications

Cartridge Type
Electret Condenser
Frequency Response
50–17000 Hz
Polar Pattern
Cardioid
Output Impedance
180 Ω
Output Configuration
Active Balanced
Sensitivity
@ 1 kHz, open circuit voltage –35 dBV/Pa (18 mV)
Maximum SPL
1 kHz at 1% THD, 1 kΩ load 124 dB
Self Noise
A-weighted 28 dB SPL
Signal-to-Noise Ratio
Ref. 94 dB SPL at 1 kHz 66 dB
Dynamic Range
1 kΩ load, @ 1 kHz 96 dB
Common Mode Rejection
10 Hz to 100 kHz 45 dB, minimum
Clipping Level
at 1% THD -6 dBV
Polarity
Positive sound pressure on diaphragm produces positive voltage on pin 2 relative to pin 3 of output XLR connector.
Weight
205 g (7.23 oz)

Environmental Conditions

Operating Temperature ­18 – 57°C (0 – 135°F)
Storage Temperature ­29 – 74°C (­20 – 165°F)
Relative Humidity 0 – 95%

Power Requirements
11–52 V DC, 2.0 mA

image 5image 6

Certifications

Meets essential requirements of all applicable European Directives.
Eligible for CE marking.
The CE Declaration of Conformity can be obtained from Shure Incorporated or any of its European representatives. For contact information please visit www.shure.com The CE Declaration of Conformity can be obtained from: www.shure.com/europe/compliance

Authorized European representative:
Shure Europe GmbH
Global Compliance
Jakob-Dieffenbacher-Str. 12
75031 Eppingen, Germany
Phone: +49-7262-92 49 0
Email:info@shure.de
www.shure.comlogo

Documents / Resources

| SHURE MX415DUAL Dual-Capsule Gooseneck Microphone [pdf] User Guide
MX415DUAL, Dual-Capsule Gooseneck Microphone
---|---

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals