behringer DIAMOND DOME DD610 Multimode RGBWA-UV LED Mirror Ball Lighting Effect User Guide
- June 7, 2024
- Behringer
Table of Contents
**behringer DIAMOND DOME DD610 Multimode RGBWA-UV LED Mirror Ball Lighting Effect User Guide
**
Important Safety Instructions
Terminals marked with this symbol carry electrical current of sufficient magnitude to constitute risk of electric shock. Use only high-quality professional speaker cables with ¼” TS or twist-locking plugs pre-installed. All other installation or modification should be performed only by qualified personnel.
This symbol, wherever it appears, alerts you to the presence of uninsulated dangerous voltage inside the enclosure – voltage that may be sufficient to constitute a risk of shock.
Caution
To reduce the risk of electric shock, do not remove the top cover (or the rear
section). No user serviceable parts inside. Refer servicing to qualified
personnel.
Caution
To reduce the risk of fire or electric shock, do not expose this appliance to
rain and moisture. The apparatus shall not be exposed to dripping or splashing
liquids and no objects filled with liquids, such as vases, shall be placed on
the apparatus.
Caution
These service instructions are for use by qualified service personnel only.
To reduce the risk of electric shock do not perform any servicing other than
that contained in the operation instructions. Repairs have to be performed by
qualified service personnel.
- Read these instructions.
- Keep these instructions.
- Heed all warnings.
- Follow all instructions.
- Do not use this apparatus near water.
- Clean only with dry cloth.
- Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
- Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
- Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding-type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.
- Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.
- Use only attachments/accessories specified by the manufacturer.
Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/ apparatus combination to avoid injury from tip-over.- Unplug this apparatus during lightning storms or when unused for long periods of time.
- Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.
- The apparatus shall be connected to a MAINS socket outlet with a protective earthing connection.
- Where the MAINS plug or an appliance coupler is used as the disconnect device, the disconnect device shall remain readily operable.
- Correct disposal of this product: This symbol indicates that this product must not be disposed of with household waste, according to the WEEE Directive (2012/19/EU) and your national law. This product should be taken to a collection center licensed for the recycling of waste electrical and electronic equipment (EEE). The mishandling of this type of waste could have a possible negative impact on the environment and human health due to potentially hazardous substances that are generally associated with EEE. At the same time, your cooperation in the correct disposal of this product will contribute to the efficient use of natural resources. For more information about where you can take your waste equipment for recycling, please contact your local city office, or your household waste collection service.
- Do not install in a confined space, such as a book case or similar unit.
- Do not place naked flame sources, such as lighted candles, on the apparatus.
- Please keep the environmental aspects of battery disposal in mind. Batteries must be disposed-of at a battery collection point.
- This apparatus may be used in tropical and moderate climates up to 40°C.
- Warning
Do not ingest battery. Chemical Burn Hazard
This product contains a coin/ button cell battery. If the coin/ button cell battery is swallowed or placed inside any part of the body, it can cause severe or fatal internal burns injuries in just 2 hours or less and can lead to death.
Keep new and used batteries away from children.
If the battery compartment does not close securely, stop using the product and
keep it away from children.
If you think batteries might have been swallowed or placed inside any part of
the body, seek immediate medical attention.
Replacement of a battery with an incorrect type can defeat a safeguard.
Replace only with the same or equivalent type.
Risk of fire or explosion if the battery is replaced by an incorrect type.
Disposal of a battery into fire or a hot oven, or mechanically crushing or
cutting of a battery, can result in an
explosion.
Leaving a battery in an extremely high temperature surrounding environment can result in an explosion or the leakage of flammable liquid or gas.
A battery subjected to extremely low air pressure may result in an explosion or the leakage of flammable liquid or gas.
Attention should be drawn to the environmental aspects of battery disposal.
LEGAL DISCLAIMER
Music Tribe accepts no liability for any loss which may be suffered by any person who relies either wholly or in part upon any description, photograph, or statement contained herein. Technical specifications, appearances and other information are subject to change without notice. All trademarks are the property of their respective owners. Midas, Klark Teknik, Lab Gruppen, Lake, Tannoy, Turbosound, TC Electronic, TC Helicon, Behringer, Bugera, Aston Microphonesand Coolaudioare trademarks or registered trademarks of Music Tribe Global Brands Ltd. © Music Tribe Global Brands Ltd. 2021 All rights reserved.
Additional Safety Instructions
-
When opening the package, take all the accessories out,
and place the device on a table for inspection. First check whether the accessories are complete, then inspect the device carefully for any damage. If there is any damage, please contact your dealer as soon as possible. -
AC Power: Check that the local power supply is in accordance with the requirements of the rated voltage of the device.
-
The device is only suitable for an indoor working environment. It should be kept in a dry environment, and away from any moisture, overheating or dust. Do not allow the device to come into contact with water, moisture, or other liquids, in order to prevent or reduce the risk of electric shock or fire.
-
Please do not install the device directly onto, or close to, combustible surfaces or materials.
-
Personnel who install, operate and maintain the device must be professionally licensed and authorized to do so.
-
If the device appears to be malfunctioning, stop using the device immediately. Do not try to repair the device, but contact the nearest authorized technical assistance center. If parts are damaged, always use identical authorized replacement parts.
-
Do not touch any electrical wiring in the process of operation, to prevent the risk of electric shock.
-
Make sure the device is used in a working environment temperature, that does not exceed 40ºC or below – 20ºC.
-
In normal operation, the highest temperature of the device housing may reach 80ºC, please do not touch.
-
The device should only be used in a grounded power system, and the ground wire must connect with the ground wire of the power supply system. The ground/earth sign of the device should be connected to the installing fixtures.
-
Do not use the device if there is damage to the power cord insulation, and also do not run the power cord so it overlaps other wires in your system.
-
When not in use or when cleaning the device, please disconnect the power cord to the device.
-
There are no user-serviceable components inside the device. Before operation of the device, please make sure the device is secure and all assembly screws and fittings are fitted. If the device outer case is open or loose, the device must not be used.
-
Regular checks must be conducted by qualified personnel to ensure that the system remains in a secure and stable condition.
-
Make sure that, where the product is suspended, the area underneath the product is free of human traffic. Do not suspend the product in areas which can be entered or used by members of the public.
Secondary Safeties
All lighting units installed in theatres, studios or other places of work and entertainment shall, in addition to the principle load bearing means of suspension, be provided with an independent, properly rated, and securely attached secondary safety. The additional safety device must be mounted in a way that the lighting unit is caught by the safety device without any drop and swing in the event that the primary suspension fails.
Product Care and Cleaning
Please pay attention to the following points when using and inspecting this product:
- All screws and components of the installed product must be tightly connected and not rusty or damaged
- The outer casing, lens, fixing parts and installation location (such as ceiling, hanger, truss, etc.) cannot be deformed
- The power cord must not be damaged.
The installation and use of the product must be carried out by trained professional technicians and must be protected against potential safety hazards.
WARNING: Please unplug the power cord before doing product maintenance!
Before disconnecting the device or starting maintenance work, make sure that
the device is disconnected. It is very important to keep the device clean and
clean. If it is kept clean, this not only keeps the output at the maximum
brightness, but it also prolongs its service life. Use high quality
professional glass cleaner and clean with a soft rag. Under no circumstances
should alcohol or chemical solvents be used. The interior of the device and
the fan should be cleaned at least quarterly using a vacuum cleaner.
WARNING: Batteries (battery pack or batteries installed) shall not be
exposed to excessive heat such as sunshine, fire or the like.
Display
Items
| No.| Silkscreen| Function
---|---|---|---
Button:
|
1
|
MENU
|
Activates main menu and toggles between menu items. Closes an open submenu without saving
2
|
DOWN
| Decreases the displayed value by one/ Navigate function
3
| UP| Increases the displayed value by one/ Navigate function
4| ENTER|
Enter selected function/ Confirm and save
LED:
|
5
| DMX| Flashes when in DMX mode
6|
MASTER
|
Flashes when in MASTER Mode
7
|
SLAVE
|
Flashes when in SLAVE Mode
8
|
SOUND
|
Flashes when in Sound Active Mode
Display Functions
Press the MENU button to access menu options, keep pressing MENU to
toggle menu items. Press the ENTER button to access desired functions and
the display will flash, then use the UP/DOWN buttons to navigate and
select the desire setting. Press ENTER to save and confirm, or press
MENU to go back without saving.
The main functions are as follows:
Controlling the Device
The device can be controlled in the following ways:
- Master/slave
- IR remote
- DMX control
Master/Slave Control
Master/Slave, automatic setting
- Connect the device(s) with DMX cable.
- Master/slave mode will be activated automatically, master unit will be set randomly.
Master/Slave, manual setting (Slave 1 mode operation)
- Connect the device(s) with DMX cable.
- Set the master unit:
- Press MENU of the first device and select
- Press ENTER
- Then use up and down to select
- Press ENTER (now the first unit is the master)
- Press MENU on the master device and select
- Press ENTER
- Then use up and down to select show mode 0-16
- Press ENTER
- After 5-10 seconds of inactivity, the show mode will be activated
- Set the slave unit(s):
- Press MENU and select . (Use the same operation on all the slave units)
- Press ENTER
- Then use up and down to select
- Press ENTER to confirm
IR Remote Control (Option)
When using the remote control, the space between the device and the remote control should be kept free of obstacles. The remote control has a range of 10 meters.
Button
|
Function
---|---
ON/OFF
| Press to turn unit on, press again to turn off
AUTO
|
Active Show, same as AU0 random
PRG
|
Active Show mode. Use + / – to select the preset program from AU1 to 16
SOUND
|
Turn Sound Control On/OFF. When ON, press + / – to adjust the sensitivity from 0 to 100 *
SPEED
|
Activates speed setting when AUTO and PRG mode is ON. Use + / – to adjust the speed from S001 to S099 *
STROBE
|
Activates strobe. Use + / – to adjust the speed from 0 to 100 *
+
|
Press to increase the current value to a maximum value of
100. Press – to decrease.
DIMMING
|
Dimmer can be used in AUTO mode, PRG mode, SOUND mode, and static color.
–
|
Press to decrease the current value to a minimum value of 0. Press + to increase.
W, A, UV, R, G, B
|
Select color for dimmer mode (White, Amber, UV, Red, Green, Blue)
1 to 9
|
Select preset color
Notes
| * Each press of +/- increases/decreases by 1, but if held down, the values change faster.
Remote Control Battery
- The battery positive (+) should face as shown below.
- The arrow indicates the plastic lock.
DMX Control
To use a DMX controller to control the device, you must first set the DMX
address code. The address code range is
In this way the device can receive the DMX signals.
- Press the MENU button, select the Menu option.
- Press ENTER button. The address code will flash. Use UP/DOWN to select DMX address code. Our factory value is set to .
- After the address code is set, hold the ENTER button.
- Connect from the output of the DMX console to the DMX input of the first slave, and connect the DMX output of the first slave to the DMX input of the second slave, and so on. Connect all the slaves.
DMX connection requires terminal (loop connection)
During the installation process, if the signal line is laid a long distance, or in a noisy environment, such as a dance hall, it is recommended to use a DMX terminal (loop connection). This can reduce any interference to the digital control signal by electrical noise.
The DMX terminator consists of a simple XLR connector with pin 2 and 3 connected to a 120 Ω resistor. Please insert the terminator into the XLR output port of the last device, please refer to the figure below.
DMX Channel Mode
DMX channel (choose default code)
DMX channel (4CH)
1
| Full dimmer| 000| –| 255|
LED dimmer from 0-100%
---|---|---|---|---|---
2
|
Strobe
|
000
| –| 005| Open
006| –| 255|
Strobe from slow to fast
3
|
Show Mode
|
000
| –| 005| No function
006| –| 020|
Show 1
021
| –| 035| Show 2
036| –| 050|
Show 3
051
| –| 065| Show 4
066| –| 080|
Show 5
081
| –| 095| Show 6
096| –| 110|
Show 7
111
| –| 125| Show 8
126| –| 140|
Show 9
141
| –| 155| Show 10
156| –| 170|
Show 11
171
| –| 185| Show 12
186| –| 200|
Show 13
201
| –| 215|
Show 14
216
| –| 230|
Show 5
231| –| 245|
Show 16
246
| –| 255|
Random show
4
| ****
Speed effect/sound
| 000| –| 249| Effect speed from slow to fast
250| –| 255|
Sound active
DMX Channel (11CH)
1
| Full dimmer| 000| –| 255|
LED dimmer from 0-100%
---|---|---|---|---|---
2
| ****
Strobe
| 000| –| 005| LED on
006| –| 255| Strobe from slow to fast
3| Red| 000| –| 255|
Red dimmer 0 – 100%
4
| Green| 000| –| 255| Green dimmer 0 – 100%
5| Blue| 000| –| 255|
Blue dimmer 0 – 100%
6| White| 000| –| 255| White dimmer 0 – 100%
7| Amber| 000| –| 255| Amber dimmer 0 – 100%
8
| UV| 000| –| 255| UV dimmer 0 – 100%
9
| ****
Motor
| 000| –| 255|
Stops
006
| –| 105| Clockwise rotation
106| –| 115|
Stops
116
| –| 215| Counterclockwise rotation
216| –| 255|
Sound controller rotation
10
| ****
Show Mode
|
000
| –| 005| No funciton
006| –| 020|
Show 1
021
| –| 035| Show 2
036| –| 050|
Show 3
051
| –| 065| Show 4
066| –| 080|
Show 5
081
| –| 095| Show 6
096| –| 110|
Show 7
111
| –| 125| Show 8
126| –| 140|
Show 9
141
| –| 155| Show 10
156| –| 170|
Show 11
171
| –| 185| Show 12
186| –| 200|
Show 13
201
| –| 215| Show 14
216| –| 230|
Show 5
231
| –| 245| Show 16
246| –| 255|
Random show
11
| ****
Speed/sound control
| 000| –| 249| Speed, slow to fast
250
| –| 255|
Sound control
Specifications
| Category | Parameter |
|---|
Light source
| 1 PCS x 12 W RGBWA-UV 6 in 1 LED
Illuminance|
1150 Lux @ 1 m
Beam angle
| 10°
Channels|
4CH, 11CH
Control mode
| DMX
Master-slave
Sound active
Color
IR
Display|
LED
Voltage
| AC100 ~240 V, 50/60 Hz
Power consumption|
16 W
Dimensions (H x W x D)
| 154 x 181 x 181 mm
Net weight|
0.55 kg
Supplied items
| DIAMOND DOME DD610 Manua
Optional items|
Clamp
Safety cable
DMX signal cable
IRC1 remote control
Other important information
-
Register online.
Please register your new MusicTribe equipment right after you purchase it by visiting musictribe.com. Registering your purchase using our simple online form helps us to process your repair claims more quickly and efficiently. Also, read the terms and conditions of our warranty, if applicable. -
Malfunction. Should your MusicTribe Authorized Reseller not be located in your vicinity, you may contact the MusicTribe Authorized Fulfiller for your country listed under “Support” at musictribe.com. Should your country not be listed, please check if your problem can be dealt with by our “Online Support” which may also be found under “Support” at musictribe.com. Alternatively, please submit an online warranty claim at musictribe.com BEFORE returning the product.
-
Power Connections.
Before plugging the unit into a power socket, please make sure you are using the correct mains voltage for your particular model. Faulty fuses must be replaced with fuses of the same type and rating without exception.
Hereby, MUSIC Tribe declares that this product is in compliance with Directive
2014/35/EU, Directive 2014/30/EU, Directive 2011/65/EU and
Amendment 2015/863/EU, Directive 2012/19/EU, Regulation 519/2012 REACH SVHC
and Directive 1907/2006/EC.
Full text of EU DoC is available at https://community.musictribe.com/
EU Representative: MUSIC Tribe Brands DK A/S
Address: Ib Spang Olsens Gade 17 Lisbjerg, DK – 8200 Aarhus N, Denmark
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>