SOUNDSTREAM Class D Car Audio Amplifier User Guide
- June 7, 2024
- SoundStream
Table of Contents
SOUNDSTREAM Class D Car Audio Amplifier User Guide
AMPLIFIERS
WARNING This symbol means important instructions. Failure to heed them can result in serious injury or death.
WARNING
-
DO NOT DRIVE WHILE DISTRACTED.
Any function that requires your prolonged attention should not be performed while driving. Always stop the vehicle in a safe location before performing any such function. Failure to do so may result in an accident. -
KEEP THE VOLUME AT MODERATE LEVELS WHILE DRIVING.
Excess volume levels can obscure sounds such as emergency vehicle sirens or road warning signals and may result in an accident. Continuous exposure to high sound pressure levels may cause permanent hearing loss. Use common sense and practice safe sound. -
FOR USE WIIB 12V NEGATIVE GROUND VEHICLE APPLICATIONS ONLY.
Using this product other than in its designed application may result in fire, injury or product damage. -
MAKE THE CORRECT WIRING CONNECTIONS AND USE PROPER FUSE PROTECTION.
Failure to connect wiring correctly or use appropriate fuse protection may result in fire, injury or product damage . -
DISCONNECT THE NEGATIVE BATTERY TERMINAL BEFORE INSTALLATION.
Failure to do so may result in fire, injury or damage to the unit. -
DO NOT ALLOW CABLES TO BECOME ENTANGLED IN SURROUNDING OBJECTS.
Arrange wiring and cables to prevent obstructions when driving. Cables or wiring that obstruct or hang up on places such as steering wheel, brake pedals, etc. can be extremely hazardous. -
DO NOT DAMAGE VEHICLE SYSTEMS OR WIRING WHEN DRILLING HOLES.
When drilling holes in the chassis for installation, take precautions so as not to contact, puncture or obstruct brake lines, fuel lines, fuel tanks, electrical wiring, etc. Failure to take such precautions may result in fire or an accident. -
DO NOT UTILIZE OR CONNECT TO ANY PART OF VEHICLE SAFETY SYSTEMS.
Bolts, nuts or wires used in the brake, airbag, steering or any other safety- related systems or fuel tanks should NEVER be used for mounting, power or ground connections. Using such parts may disable control of the vehicle or result in fire.
CAUTION This symbol means important instructions.
Failure to heed them can result in injury or property damages.
CAUTION
-
STOP USE IMMEDIATELY IF A PROBLEM OCCURS.
Failure to do so may result in personal injury or damage to the product. Return it to your authorized dealer. -
HAVE AN EXPERT DO THE WIRING AND INSTALLATION.
This unit requires special technical skill and experience for wiring and installation. To insure safety and proper function, always contact the authorized dealer where you purchased the product to have it done professionally. -
INSTALL THE UNIT SECURELY WITH SPECIFIED PARTS.
Be sure to use only the included parts and specified installation accessories (not included). Use of other than designated parts may damage this unit. Install the unit securely so that it will not come loose during a collision or sudden jolt. -
ROUTE WIRING AWAY FROM SHARP EDGES AND MOVING PARTS.
Arrange cables and wiring away from sharp or pointed edges and avoid moving parts such as seat hinges or rails to prevent pinching or wear. Use loom protection where appropriate and always use a grommet for any wiring routed through metal. -
NEVER RUN SYSTEM WIRING OUTSIDE OR UNDERNEATH THE VEIDCLE.
All wiring must be routed, secured and protected inside the vehicle. Failure to do so may result in fire, injury or property damage. -
INSTALL THE UNIT IN A DRY AND VENTILATED LOCATION.
Avoid mounting locations where the unit will likely be exposed to high moisture or heat without adequate ventilation. Moisture penetration or heat buildup may result in product failure. -
REDUCE GAIN AND SOURCE VOLUME TO MINIMUM LEVELS FOR INITIAL SYSTEM TUNING AND BEFORE CONNECTION TO AN AMPLIFIER.
Ensure amplifier power is off before connecting RCA cables and follow proper system gain setting procedures. Failure to do so may result in damage to the amplifier and/or connected components.
TECHNICAL FEATURES
Sound stream Digital Pre-Amp amplifiers offer-up an innovative approach to traditional sound processing. DPA amps include a digital signal processing integrated circuit module that opens the door for precise tuning of crossovers & gain settings. keeping the user in mind, all functions are controlled by top surface mounted keys, needing only a finger press & knob turn. Selected crossover frequencies and gain levels are displayed on an adjacent LCD, showing operating voltage & temperature while idle. Full-featured pre-amp options, including band-pass & subsonic crossovers, bass boost, & even variable phasing make DPA amps a go-to for any enthusiast.
ADDITIONAL SPECIFICATION
DPA4.1600D
- Additional Specifications:
- 80w x 4 @ 4-ohm Stereo
- 160w x 4@ 2-ohm Stereo
- 320w x 2 @ 4-ohm Bridged
- 1,600w MAX Power
- 20-20kHz 48dB High Pass Crossover
- 20-20kHz 48dB Low Pass Crossover
- 0-14dB 45Hz Bass Boost Equalizer
- Total Harmonic Distortion: 0.5%(4.Q)
- Frequency Response: 10-25kHz
- Signal-to-Noise Ratio: 70dB
- Input Sensitivity: 250mV-8V
- Dimensions: 4″w x 1.75″h x 9″ l
DPAl.2000D
- Additional Specifications:
- 250w x 1 @ 4-ohrn Mono
- 400w x 1 @ 2-ohrn Mono
- 2,000w MAX Power
- 30-250Hz 48dB Low Pass Crossover
- 10-SOHz 48dB Subsonic Crossover
- 0-14dB 45Hz Bass Boost Equalizer
- Total Harmonic Distortion: 0.5%(40)
- Frequency Response: 10-lkHz
- Signal-to-Noise Ratio: 70dB
- Input Sensitivity: 250mV-8V
- Dimensions: 4″w x l.75″h x 9″ I
DPAS.2000D
- Additional Specifications:
- 75w x 4 (40 Stereo)+ 200w x 1 (40 Mono)
- 125w x 4 (2 0 Stereo)+ 400w x 1 (2 0 Mono)
- 250w x 2 (40 Bridged)+ 400w x 1 (2 O Mono)
- 2.000w Combined MAX Power
- 20-20kHz 48dB High Pass Crossover (ch.1-4)
- 20-20kHz 48dB Low Pass Crossover (ch.1-4)
- 20-lkHz 48dB Low Pass Crossover ( ch.5)
- 10-SOHz 48dB Subsonic Crossover (ch.5)
- 0-14dB 45Hz Bass Boost Equalizer (ch.5)
- 0-180° Phase Shift (ch.5)
- Total Harmonic Distortion: 0.5%(40)
- Frequency Response: 10-25kHz
- Signal-to-Noise Ratio: 70dB
- Input Sensitivity: 250mV-8V
- Dimensions: 4″w x l.75″h x 11.5” I
FUNCTION
DPA4.1600D
DPAl.2000D
DPAS.2000D
REMOTE SUB WOOFER LEVEL CONTROL
This input allows you to add remote that will allow you to control the subwoofer output of your Sound Stream amplifier from your dashboard. and to adapt the amplifier to all kind of signal sources with varying levels there are a level control provided on the amplifier next to the phone jacks. It should not be used as volume controls. Start with a “12′ clock” setting of the level controls. If you set the head unit volume to 75% of maximum you should achieve a good sound without distortion. Find a point of the level setting where the distortion is just discernible. At this point slightly reduce the control.
HOW TO INSTALLATION
The dash control mounts with two screws, which attach to the underside of the dashboard. Slide under the dash and place the dash control in its mounting position, mark the two mounting holes, drill pilot holes, and secure with two screws.
POWER & SPEAKER CONNECTION
How to connect hi-input and low-input mode.
The input can use both hi- input and low- inputs. When connecting by Hi-input, use the cable provided by the manufacturer as shown.
How to connect hi-input and low-input mode.
The input can use both hi- input and low- inputs. When connecting by Hi-input, use the cable provided by the manufacturer as shown.
5-channel gain control method.
You can increase the output by raising the level of the top panel. And you must connect the remote control to increase the more output.
These amplifiers are designed to work within a 10 to 16.8 volt DC range. Before any wires are connected, the vehicles electrical system should be checked for correct voltage supply with the help of a voltmeter.
First, check the voltage at the battery with the ignition in the OFF position. The voltmeter should read no less than 12V. If your vehicles electrical system is not up to these specifications, we recommend having it checked by an auto electrician before any further installation. Once the vehicle is checked, make certain the correct cable size is used. We recommend using as large a gauge cable as possible, use the Power Cable Selection Chart to calculate the correct power wire size for your application.
Power
This amplifier should be wired directly to the vehicle battery using the
appropriate size cable. Start at the vehicle battery and run the power cable
through to the amplifier. Avoid running the power cable over engine components
and near heater cores. The use of an inline fuse or circuit breaker is a must;
this will prevent the risk of a potential fire caused by a short in your power
cable. Connect the fuse holder or circuit breaker as close to the battery
positive(+) terminal as possible (no farther then 18″ from the battery). This
fuse or circuit breaker should be no greater then the sum of the fuses found
on the chassis of your amplifier (also see specifications chart). You may now
connect the cable to the battery, but remember to leave the fuse out or
circuit breaker “for’ until all other cable connections are made.
Ground
When grounding your amplifier, locate a metal area close to the amplifier that
is good source of ground (preferably the floor pan). Once again, investigate
the area you wish to use for electrical wires, vacuum lines, and brake or fuel
lines. Use either a wire brush or sandpaper to eliminate unwanted paint for
better contact of the ground. Secure the ground cable to the body using a
bolt, star washer and nut. Spread silicon over the screw and bare metal to
prevent rust and possible water leaks.
Now it’s time to connect the power and ground cables to the amplifier.
Cut both cables to length. Strip off 1/2 -inch (12mm) of the insulation so
that the bare wire fits all the way in the terminal block
on the side panel of the amplifier, seating it firmly so no bare wire is
exposed. Use a Philips (cross) type screwdriver to loosen the +BATT and the
GND connections on the amplifier. Insert the ground first, and then the + 12V
and please make sure that you place them into the correctly marked terminals.
Then tighten the screws down securely.
Remote
This terminal must be connected to a switched +12V source. Typically, remote
tum-on leads are provided at the source unit that will tum on and off the
amplifier in correspondence with the source. If the source unit does not have
a remote tum-on lead, then a power antenna wire can be used. If neither of
these leads is available at the source unit, then a switched+ 12V supply must
be used, like the ACC,+12V.
REMOTE WIRE
Some signal cables include a thin wire for remote amplifier start. High
quality cables normally requires a separate wire for this. Connect between the
head units remote cable ( often the same cable that’s used for automatic power
antennas) and the REM-terminal on the amplifier.
NOTE! If you want to start more than one amplifier using the remote output, the current load might be too high for some head units. High currents may damage the head unit, check in the manual for the head unit. Sometimes you must add a relay to the remote circuit that takes care of the higher current. If you are uncertain of how to connect the relay, ask your local DLS dealer for advice.
SPEAKER CONNECTION
Always use high quality speaker cables . Connect the speaker+ (marked with +
or a red dot) to the amplifier + terminal, and the speaker When fitting the
cables to the terminals, remove only 10 mm of the insulation. 1 vest the wire
strand together and insert the wire after loosening the terminal screw. Do not
over tighten as this can cut the cable strands.
To prevent the cable insulation from being damaged over sharp metal edges we
recommend the use of cable protection tubes or similar. A damaged cable
insulation could cause serious damage to the amplifier not covered by any
guarantee.
SPEAKER POLARITY CHECK
All speakers in a car audio system should be connected in phase (the same
polarity). All speaker cones must move in the same direction. Out of phase
speakers will cause a lack of bass, and a poor stereo soundstage.
WARNING: This product can expose you to chemicals including DEHP which is known to the State of California to cause Cancer, Birth Defects or other reproduction harm. For more information go to www.P6Swamlngs.ca.gov.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>