SOUNDSTREAM REIGN 1-Channel Amplifier Owner’s Manual

June 6, 2024
SoundStream

SOUNDSTREAM REIGN 1-Channel Amplifier

Panel Definition

SR1-1500

SR1-3000

Features & Functions

Power Connection

For your convenience, high current barrier strip terminals are provided which allow the use of heavy gauge terminals and wire without splicing.

B+/+12V. Connect the +12V pole of battery.
GND. Connect the chassis ground of auto.
REM. Connect to the remote turn-on lead of your headunit.

Note:
Improper wiring connections can seriously damage amplifiers, accessories, or speakers, please follow instructions carefully.
Disconnect the battery positive(+) before making any power connections to the amplifier.
Make sure all connections are clean and secure, and use gromments when going through the firewall and other metal bodywork.
Always use the proper size fusing, with a fuse at the battery and the amplifier.(not supplied)

Input Connection

Connect the pre-amp( low-level) outputs from your source unit or crossover to the RCA jacks labeled “input” on the amplifier. Be sure to route all signal cable away from power lines and use high quality
RCA cables to insure good signal transfer and to avoid noise from entering the system.
In the Stereo mode, connect the left and right RCA plugs from the source unit to their appropriate input jacks.
In the Mono/Bridged mode, connections may be made to right, left of both input jacks.

Output connection

Again, high current barrier strip terminals are provide for connection to the loud speaker system.
Connect the subwoofer speaker+ lead to the+ terminal and the subwoofer spakerlead to the terminal.

Note: Mono mode is designed for 2-8 ohm loads. If connecting two subwoofer speakers, the unit will not support a 1 ohm load.

Connect two Subwoofer Systems

Connect the two pairs of output terminals to corresponding subwoofer speakers:

Output connection:

Connect one Subwoofer System

1st speaker connection

2nd speaker connection

TROUBLE SHOOTING

No Audio
  • Low or no remote turn-on voltage: check remote connections at the amplifier and source unit.
  • Blown amplifier fuse: replace with a new fast-blow fuse (same rating).
  • Power wires not connected: check battery and ground wiring at the amplifier and check the battery connections.
  • Speaker leads shorted: check speaker continuity to ground; it should not show a common ground.
  • Speakers not connected or are blown: check speaker connections at the amplifier; measure coil impedance.
Distorted audio
  • Gain is not properly set or the speaker cones are damaged.
  • Review the instructions for setting the gain. Inspect each speaker cone for signs of damage, such as a frozen cone, burning smell, etc.

Features

  • Digital pulse-width-modulated regulated power supply.
  • Mosfet power supply devices.
  • Direct coupled output stage.
  • Discrete output transistors.
  • Low overall negative feedback.
  • Bridgeable to mono operation.
  • Soft start delayed turnon.
  • Increased surface area and mass for continuous heat dissipation.
  • LED power on indicator.
  • 1-ohm Stable Monoblock Operation for MAX Power
  • Bridge 2 Monoblocks Together for Double Power!
  • Military Grade PCB w/ PWM MOSFET Power Supply
  • Direct Short, Thermal, & Overload Circuit Protection
  • High/Speaker Level & Low Level/RCA Input
  • 4g Power Wire & 8g Speaker Wire Outputs
  • Variable 12dB High & Low Pass Crossovers
  • 12dB Bass Boost Increases Low Octave Harmonics

Specification

Output Power: SR1-1500: 1x500W(2 Q RMS)/ 1x300W(4Ω RMS)

SR1-3000: 1x1000W(2Q RMS)/ 1x600W(4Ω RMS)
THD:| <0.1%
Frequency RESP:| 10Hz ~ 300Hz ±1dB
S/N Ratio:| ≥ 85dB
Input Sensitivity:| 200mV~8V
Bass Boost:| 12dB
Speaker Impedance:| 2~80
Power Fuse:| SR1-1500: 25Ax2 ( Refer flank text)
SR1-3000: 40Ax2 ( Refer flank text)
Dimension (HxWxL):| SR1-1500: 2.3″H x 7.25″W x 10.25″L
SR1-3000: 2.3″H x 7.25″W x 9.85″L
Accessory:| Screws Set & Spare Fuse

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

SoundStream User Manuals

Related Manuals