SOUNDSTREAM DPA4.1600D Class D Car Audio Amplifier Owner’s Manual

June 4, 2024
SoundStream

SOUNDSTREAM DPA4.1600D Class D Car Audio logo

SOUNDSTREAM DPA4.1600D Class D Car Audio Amplifier

SOUNDSTREAM DPA4.1600D Class D Car Audio logo

AMPLIFIRES

WARNING
This symbol means important instructions. Failure to heed them can result in serious injury or death.
WARNING

  • DO NOT DRIVE WHILE DISTRACTED.
    Any function that requires your prolonged attention should not be performed while driving. Always stop the vehicle in a safe location before performing any such function. Failure to do so may result in an accident.

  • KEEP THE VOLUME AT MODERATE LEVELS WHILE DRIVING.
    Excess volume levels can obscure sounds such as emergency vehicle sirens or road warning signals and may result in an accident. Continuous exposure to high sound pressure levels may cause permanent hearing loss. Use common sense and practice safe sound.

  • FOR USE WITH 12V NEGATIVE GROUND VEIDCLE APPLICATIONS ONLY.
    Using this product other than in its designed application may result in fire, injury or product damage.

  • MAKE THE CORRECT WIRING CONNECTIONS AND USE PROPER FUSE PROTECTION.
    Failure to connect wiring correctly or use appropriate fuse protection may result in fire, injury or product damage .

  • DISCONNECT THE NEGATIVE BATTERY TERMINAL BEFORE INSTALLATION. Failure to do so may result in fire, injury or damage to the unit.

  • DO NOT ALLOW CABLES TO BECOME ENTANGLED IN SURROUNDING OBJECTS.
    Arrange wiring and cables to prevent obstructions when driving. Cables or wiring that obstruct or hang up on places such as steering wheel, brake pedals, etc. can be extremely hazardous.

  • DO NOT DAMAGE VEIDCLE SYSTEMS OR WIRING WHEN DRILLING HOLES.
    When drilling holes in the chassis for installation, take precautions so as not to contact, puncture or obstruct brake lines, fuel lines, fuel tanks, electrical wiring, etc. Failure to take such precautions may result in fire or an accident.

  • DO NOT UTILIZE OR CONNECT TO ANY PART OF VEIDCLE SAFETY SYSTEMS.
    Bolts, nuts or wires used in the brake, airbag, steering or any other safety- related systems or fuel tanks should NEVER be used for mounting, power or ground connections. Using such parts may disable control of the vehicle or result in fire.

CAUTION
This symbol means important instructions. Failure to heed them can result in injury or property damages.
CAUTION

  • STOP USE IMMEDIATELY IF A PROBLEM OCCURS.
    Failure to do so may result in personal injury or damage to the product. Return it to your authorized dealer.

  • HAVE AN EXPERT DO THE WIRING AND INSTALLATION.
    This unit requires special technical skill and experience for wiring and installation. To insure safety and proper function, always contact the authorized dealer where you purchased the product to have it done professionally.

  • INSTALL THE UNIT SECURELY WITH SPECIFIED PARTS.
    Be sure to use only the included parts and specified installation accessories (not included). Use of other than designated parts may damage this unit. Install the unit securely so that it will not come loose during a collision or sudden jolt.

  • ROUTE WIRING AWAY FROM SHARP EDGES AND MOVING PARTS.
    Arrange cables and wiring away from sharp or pointed edges and avoid moving parts such as seat hinges or rails to prevent pinching or wear. Use loom protection where appropriate and always use a grommet for any wiring routed through metal.

  • NEVER RUN SYSTEM WIRING OUTSIDE OR UNDERNEATH THE VEIDCLE.
    All wiring must be routed, secured and protected inside the vehicle. Failure to do so may result in fire, injury or property damage.

  • INSTALL THE UNIT IN A DRY AND VENTILATED LOCATION.
    Avoid mounting locations where the unit will likely be exposed to high moisture or heat without adequate ventilation. Moisture penetration or heat buildup may result in product failure.

  • REDUCE GAIN AND SOURCE VOLUME TO MINIMUM LEVELS FOR INITIAL
    SYSTEM TUNING AND BEFORE CONNECTION TO AN AMPLIFIER.
    Ensure amplifier power is off before connecting RCA cables and follow proper system gain setting procedures. Failure to do so may result in damage to the amplifier and/or connected components.

TECHNICAC FEATURES

Sound stream Digital Pre-Amp amplifiers offer-up an innovative approach to traditional sound processing. DPA amps include a digital signal processing integrated circuit module that opens the door for precise tuning of crossovers & gain settings. keeping the user in mind, all functions are controlled by top surface mounted keys, needing only a finger press & knob turn. Selected crossover frequencies and gain levels are displayed on an adjacent LCD, showing operating voltage & temperature while idle. Full-featured pre-amp options, including band-pass & subsonic crossovers, bass boost, & even variable phasing make DPA amps a go-to for any enthusiast

ADDITIONAL SPECIFICATIONS

DPA4.1600D

  •  Additional Specifications:
  •  80w x 4 @ 4-ohm Stereo
  •  160w x 4 @ 2-ohm Stereo
  •  320w x 2 @4-ohm Bridged
  • 1,600w MAX Power
  • 20-20kHz 48dB High Pass Crossover
  • 20-20kHz 48dB Low Pass Crossover
  •  0-14dB 45Hz Bass Boost Equalizer
  •  Total Harmonic Distortion: 0.5%( 4 D)
  •  Frequency Response: 10-25kHz
  •  Signal-to-Noise Ratio: 70dB
  •  Input Sensitivity: 250mV-8V
  • Dimensions: 4″w x 1.75″h x 9″ 1
    SOUNDSTREAM DPA4.1600D Class D Car Audio 01

DPAl.2000D

  •  Additional Specifications:
  • 250w x 1 @ 4-ohm Mono
  • 400w x 1 @ 2-ohm Mono
  •  2,000w MAX Power
  •  30-250Hz 48d.B Low Pass Crossover
  •  10-50Hz 48dB Subsonic Crossover
  •  0-l 4dB 45Hz Bass Boost Equalizer
  •  Total Harmonic Distortion: 0.5%( 4 Q)
  • Frequency Response: 10-lkHz
  •  Signal-to-Noise Ratio: 70dB
  •  Input Sensitivity: 250mV-8V
  •  Dimensions: 4″w x 1.75″h x 9″ 1
    SOUNDSTREAM DPA4.1600D Class D Car Audio 02

DPAS.2000D

  •  Additional Specifications:
  •  75w x 4 (4!1 Stereo)+ 200w x 1 (4!1 Mono)
  •  125w x 4 (2 Q Stereo)+ 400w x 1 (2 Q Mono)
  •  250wx 2 (4!1 Bridged)+ 400wx 1 (2!1 Mono)
  •  2.000w Combined MAX Power
  •  20-20kHz 48dB High Pass Crossover (ch.1-4)
  • 20-20kHz 48d.B Low Pass Crossover (ch.1-4)
  • 20-lkHz 48dB Low Pass Crossover ( ch.5)
  •  10-50Hz 48dB Subsonic Crossover (ch.5)
  • 0-14dB 4 5Hz Bass Boost Equalizer ( ch. 5)
  •  0-180° Phase Shift ( ch.5)
  • Total Harmonic Distortion: 0.5%( 4 Q)
  •  Frequency Response: 10-25kHz
  • Signal-to-Noise Ratio: 70dB
  • Input Sensitivity: 250mV-8V
  •  Dimensions: 4″w x 1.75″h x 11.5″ 1SOUNDSTREAM DPA4.1600D Class D Car Audio 03

FUNCTION

DPA4.1600D
SOUNDSTREAM DPA4.1600D Class D Car Audio 04

A) FRONT & REAR LEVEL ADJUST.
SOUNDSTREAM DPA4.1600D Class D Car Audio 04

  1.  Press the LED button.
  2.  And Press the LED Button.(LED Button blinks when adjusting And LED Button is on after adjustment.)
  3.  Tum the volume .ft to adjust the level. And If you think the sound is small, tum the gain on the front to make it louder.
  4.  It will change the level value in the display  it is changed from 1 to 20.
  5.  And press the volume to save the set value.

B) FRONT & REAR ID-PASS FITER ADJUST.SOUNDSTREAM DPA4.1600D Class D Car
Audio 06

  1.  Press the LED button.
  2. And Press the LED Button. (LED Button blinks when adjusting And LED Button is on after adjustment.)
  3.  Tum the volume to adjust the level.
  4. It will change the level value in the display  it is changed from 20Hz to 20KHz.
  5.  And press the volume .ft to save the set value.

C) FRONT & REAR LOW PASS FILTER ADJUST.SOUNDSTREAM DPA4.1600D Class D Car
Audio 06

  1. Press the LED button.
  2. And Press the LED Button. e (LED Button blinks when adjusting And LED Button is on after adjustment.)
  3.  Tum the volume to adjust the level.
  4.  It will change the level value in the display it is changed from 20Hz to 20KHz.
  5.  And press the volume .ft to save the set value.

D) FRONT & REAR BASS BOOST ADJUST.SOUNDSTREAM DPA4.1600D Class D Car
Audio 08

  1. Press the LED button.
  2.  And Press the LED Button. (LED Button blinks when adjusting And LED Button is on after adjustment.)
  3.  Tum the volume  to adjust the level.
  4. It will change the level value in the display  it is changed from 0dB to14dB.
  5.  And press the volume to save the set value.

E) FRONT & REAR BAND PASS ADJUST.SOUNDSTREAM DPA4.1600D Class D Car Audio
09

  1.  Press the LED button.
  2. And Press the LED Button.  (LED Button blinks when adjusting And LED Button is on after adjustment.)
  3. Tum the volume .ft to adjust the level.
  4. It will change the level value in the display IHB.BI:: it is changed from 20Hz to 20KHz.
  5.  And press the volume  to save the set value.

DPAl.2000DSOUNDSTREAM DPA4.1600D Class D Car Audio
09 E) LEVEL ADJUST.SOUNDSTREAM DPA4.1600D Class D
Car Audio 11

  1.  Press the LED button (LED Button blinks when adjusting And LED Button is on after adjustment.)

  2. Tum the volume  to adjust the level. There is no gain on 5 channels because of design so use the remote control.
    The gain value of the remote is showed on the display and the value is changed from 1 to 25.

  3.  It will change the level value in the display  it is changed from 1 to 20.

  4. And press the volume to save the set value .

F) LOW PASS FILTER ADJUST.SOUNDSTREAM DPA4.1600D Class D Car Audio
12

  1. Press the LED button.(LED Button is blinking when adjusting And LED Button is on after adjustment.)
  2. Tum the volume to adjust the level.
  3.  It will change the level  value in the display it is changed from 20Hz to lKHz.
  4. And press the volume  to save the set value.

G) SUB SONIC FILTER ADJUST.SOUNDSTREAM DPA4.1600D Class D Car Audio
13

  1. Press the LED button.  (LED Button is blinking when adjusting And LED Button is on after adjustment.)
  2.  Tum the volume to adjust the level.
  3.  It will change the level value in the display it is changed from 10Hz to 50Hz.
  4.  And press the volume  to save the set value.

H) BASS BOOST ADJUST.SOUNDSTREAM DPA4.1600D Class D Car Audio
14

  1. Press the LED button.(LED Button is blinking when adjusting And LED Button is on after adjustment.)
  2. Tum the volume to adjust the level.
  3. It will change the level value in the display  it is changed from 0dB to 14dB.
  4.  And press the volume to save the set value.

I) PHASE SIDFT ADJUST.SOUNDSTREAM DPA4.1600D Class D Car Audio
14

  1. Press the LED button.(LED Button is blinking when adjusting And LED Button is on after adjustment.)
  2. Tum the volume  to adjust the level.
  3. It will change the level value in the display  it is changed from 0° to 180°.
  4.  And press the volume to save the set value.

DPAS.2000DSOUNDSTREAM DPA4.1600D Class D Car Audio
16

A) FRONT & REAR LEVEL ADJUST.
SOUNDSTREAM DPA4.1600D Class D Car Audio 17

  1. Press the LED button.
  2. And Press the LED Button. (LED Button blinks when adjusting And LED Button is on after adjustment.)
  3.  Tum the volume  to adjust the level. And If you think the sound is small, tum the gain on the front to make it louder.
  4. It will change the level value in the display it is changed from 1 to 20.
  5.  And press the volume  to save the set value.

B) FRONT & REAR HI-PASS FITER ADJUST.SOUNDSTREAM DPA4.1600D Class D Car
Audio 18

  1.  Press the LED button.
  2.  And Press the LED Button. I (LED Button blinks when adjusting And LED Button is on after adjustment.)
  3.  Tum the volume to adjust the level.
  4. It will change the level value in the display  it is changed from 20Hz to 20KHz.
  5. And press the volume  to save the set value.

C) FRONT & REAR LOW PASS FILTER ADJUST.SOUNDSTREAM DPA4.1600D Class D Car
Audio 18

  1. Press the LED button.
  2. And Press the LED Button.  (LED Button blinks when adjusting And LED Button is on after adjustment.)
  3.  Tum the volume to adjust the level.
  4.  It will change the  value in the display  it is changed from 20Hz to 20KHz.
  5.  And press the volume to save the set value.

D) FRONT & REAR BAND PASS ADJUST.SOUNDSTREAM DPA4.1600D Class D Car Audio
20

  1.  Press the LED button.
  2.  And Press the LED Button.   (LED Button blinks when adjusting And LED Button is on after adjustment.)
  3. Tum the volume to adjust the level.
  4. It will change the level value in the display  it is changed from 20Hz to 20KHz.
  5. And press the volume to save the set value.

E) LEVEL ADJUST.SOUNDSTREAM DPA4.1600D Class D Car Audio
21

  1. Press the LED button.  (LED Button blinks when adjusting And LED Button is on after adjustment.)

  2. Tum the volume to adjust the level. There is no gain on 5 channels because of design so use the remote control. The gain value of the remote is showed on the display
    and the value is changed from 1 to 25.

  3.  It will change the level value in the display it is changed from 1 to 20.

  4.  And press the volume to save the set value.

F) LOW PASS FILTER ADJUST.SOUNDSTREAM DPA4.1600D Class D Car Audio
22

  1. Press the LED button. (LED Button is blinking when adjusting And LED Button is on after adjustment.)
  2.  Turn the volume  to adjust the level.
  3. It will change the level value in the display  it is changed from 20Hz to lKHz.
  4. And press the volume  to save the set value.

G) SUB SONIC FILTER ADJUST.SOUNDSTREAM DPA4.1600D Class D Car Audio
23

  1.  Press the LED button. (LED Button is blinking when adjusting And LED Button is on after adjustment.)
  2.  Tum the volume  to adjust the level.
  3.  It will change the level value in the display  it is changed from 10Hz to 50Hz.
  4.  And press the volume to save the set value.

H) BASS BOOST ADJUST.SOUNDSTREAM DPA4.1600D Class D Car Audio
24

  1. Press the LED button. (LED Button is blinking when adjusting And LED Button is on after adjustment.)
  2.  Turn the volume  to adjust the level.
  3.  It will change the level value in the display  it is changed from 0dB to 14dB.
  4.  And press the volume  to save the set value.

I) PHASE SIDFT ADJUST.SOUNDSTREAM DPA4.1600D Class D Car Audio
25

  1.  Press the LED button. (LED Button is blinking when adjusting And LED Button is on after adjustment.)
  2.  Tum the volume  to adjust the level.
  3.  It will change the level value in the display  it is changed from 0° to 180°
  4.  And press the volume  to save the set value.

DISPLAY DESCRIPTION

  1.  Thermal  protection.
    • a. The thermal protection circuit is worked when the temperature of the product reaches 160F degrees. And the display will show as above and it will again work when the temperature drops SOF degrees.
  2.  Voltage and temperature indication.
    • a. The default is voltage.
    • b. Press shortly the volume  Then the display will change from voltage to temperature.
    • b. Press longer the volume  Then the display will change from Celsius to Fahrenheit.
  3. How to reset.
  • a. If there is a problem with the product, press the volume ;A more than 10 seconds.

REMOTE SUBWOOFER LEVEL CONTROL
This input allows you to add remote that will allow you to control the subwoofer output of your Sound Stream amplifier from your dashboard. and to adapt the amplifier to all kind of signal sources with varying levels there are a level control provided on the amplifier next to the phone jacks. It should not be used as volume controls. Start with a “12′ clock” setting of the level controls. If you set the head unit volume to 7 5% of maximum you should achieve a good sound without distortion. Find a point of the level setting where the distortion is just discernible. At this point slightly reduce the control.

HOW TO INSTALLATION

The dash control mounts with two screws, which attach to the underside of the dashboard. Slide under the dash and place the dash control in its mounting position, mark the two mounting holes, drill pilot holes, and secure with two screws.SOUNDSTREAM DPA4.1600D Class D Car Audio 25 POWER & SPEAKER CONNECTION
How to connect hi-input and low-input mode.SOUNDSTREAM DPA4.1600D Class D
Car Audio 27

  • The input can use both hi- input and low- inputs.
    When connecting by Hi-input, use the cable provided by the manufacturer as shown.
    SOUNDSTREAM DPA4.1600D Class D Car Audio 28

  • How to make a high input connector.
    DPA4.1600D

    80W x 4ch.| 4Ohm.| 14.4V l Khz RMS.
    l60Wx4ch.| 2Ohm.| 14.4V l Khz RMS.
    320W x 2ch.| 4Ohm.| 14.4V l Khz RMS.
    1.600W| MAX POWER

How to connect hi-input and low-input mode.SOUNDSTREAM DPA4.1600D Class
D Car Audio 29

  • The input can use both hi- input and low- inputs.
    When connecting by Hi-input, use the cable provided by the manufacturer as shown.
    SOUNDSTREAM DPA4.1600D Class D Car Audio 30

  • How to make a high input connector.
    DPA1.2CXXJD

    250Wx lch.| 4Ohm. I 14.4V 100Hz RMS.
    400Wx lch.| 2Ohm. I 14.4V 100Hz RMS.
    2.000W| MAX POWER

5-channel gain control method.SOUNDSTREAM DPA4.1600D Class D Car Audio
31

  • You can increase the output by raising the level of the top panel. And you must connect the remote control to increase the more output.
    DPA5.2000D

    75W x 4ch.| 4Ohm.| 14.4V l Khz RMS.
    125W x4ch.| 2Ohm.| 14.4V l Khz RMS.
    250W x 2ch.| 4Ohm.| 14.4V l Khz RMS.
    200W x lch.| 4Ohm.| 14.4V lO0Hz RMS.
    ---|---|---
    400W x lch.| 2Ohm.| 14.4V lO0Hz RMS.
    2,000W| MAX POWER

These amplifiers are designed to work within a 10 to 16.8 volt DC range. Before any wires are connected, the vehicles electrical system should be checked for correct voltage supply with the help of a voltmeter. First, check the voltage at the battery with the ignition in the OFF position. The voltmeter should read no less than 12V. If your vehicles electrical system is not up to these specifications, we recommend having it checked by an auto electrician before any further installation. Once the vehicle is checked, make certain the correct cable size is used. We recommend using as large a gauge cable as possible, use the Power Cable Selection Chart to calculate the correct power wire size for your application.
Power
This amplifier should be wired directly to the vehicle battery using the appropriate size cable. Start at the vehicle battery and run the power cable through to the amplifier. A void running the power cable over engine components and near heater cores. The use of an inline fuse or circuit breaker is a must; this will prevent the risk of a potential fire caused by a short in your power cable. Connect the fuse holder or circuit breaker as close to the battery positive ( +) terminal as possible (no farther then 18″ from the battery). This fuse or circuit breaker should be no greater then the sum of the fuses found on the chassis of your amplifier (also see specifications chart). You may now connect the cable to the battery, but remember to leave the fuse out or circuit breaker “off” until all other cable connections are made.
Ground
When grounding your amplifier, locate a metal area close to the amplifier that is good source of ground (preferably the floor pan). Once again, investigate the area you wish to use for electrical wires, vacuum lines, and brake or fuel lines. Use either a wire brush or sandpaper to eliminate unwanted paint for better contact of the ground. Secure the ground cable to the body using a bolt, star washer and nut. Spread silicon over the screw and bare metal to prevent rust and possible water leaks. Now it’s time to connect the power and ground cables to the amplifier. Cut both cables to length. Strip off 1/2 -inch (12mm) of the insulation so that the bare wire fits all the way in the terminal block on the side panel of the amplifier, seating it firmly so no bare wire is exposed. Use a Philips (cross) type screwdriver to loosen the +BATT and the GND connections on the amplifier. Insert the ground first, and then the+ 12V and please make sure that you place them into the correctly marked terminals. Then tighten the screws down securely.
Remote
This terminal must be connected to a switched + 12V source. Typically, remote turn-on leads are provided at the source unit that will turn on and off the amplifier in correspondence with the source. If the source unit does not have a remote tum-on lead, then a power antenna wire can be used. If neither of these leads is available at the source unit, then a switched+ 12V supply must be used, like the ACC, +12V.

REMOTE WIRE
Some signal cables include a thin wire for remote amplifier start. High quality cables normally requires a separate wire for this. Connect between the head units remote cable (often the same cable that’s used for automatic power antennas) and the REM-terminal on the amplifier.
NOTE!
If you want to start more than one amplifier using the remote output, the current load might be too high for som head units. High currents may damage the head unit, check in the manual for the head unit. Sometimes you must add a relay to the remote circuit that takes care of the higher current. If you are uncertain of how to connect the relay, ask your local DLS dealer for advice.
SPEAKER CONNECTION
Always use high quality speaker cables . Connect the speaker + (marked with + or a red dot) to the amplifier + terminal, and the speaker
When fitting the cables to the terminals, remove only 10 mm of the insulation. Twist the wire strand together and insert the wire after loosening the terminal screw. Do not over tighten as this can cut the cable strands. To prevent the cable insulation from being damaged over sharp metal edges we recommend the use of cable protection tubes or similar. A damaged cable insulation could cause serious damage to the amplifier not covered by any guarantee.
SPEAKER POLARITY CHECK
All speakers in a car audio system should be connected in phase (the same polarity). All speaker cones must move in the same direction. Out of phase speakers will cause a lack of bass, and a poor stereo soundstage.

WARNING:
This product can expose you to chemicals including DEHP which is known to the State of California to cause Cancer, Birth Defects or other reproduction harm. For more information go to www.P65wamlngs.ca.gov.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

SoundStream User Manuals

Related Manuals