SOUNDSTREAM VRCPAA-70M AV Media Receiver User Manual

SOUNDSTREAM VRCPAA-70M AV Media Receiver

INTRODUCTION

Safety Warnings and Considerations (for Amplifier / DSP / Active Woofer)

•  Clean only with a dry cloth or other similar materials.
•  Install your product in a dry, well-ventilated location that does not interfere with your vehicle’s safety equipment.
•  Do not block any ventilation openings when installing this product.
• Do not mount the product in the engine compartment of your vehicle or in any areas of extreme heat such as muffiers, silencers, exhaust pipes or other heat producing apparatus.
• Securely mount the product so that it does not come loose in the event of a collision or as a result of repeated vibrations that might occur during normal operation.
• Installation of the apparatus must be done with great care to prevent damage to your vehicle’s fuel lines, power, and other electrical wiring, hydraulic brake lines, and other systems. If possible always visit your nearest Nakamichi dealer to perform the installation.
•  Do not run any wiring outside or underneath the vehicle. Keep all wires inside the vehicle.
• Take the necessary precautions when making connections to the vehicle’s battery to avoid any potential shock.
• Protect all system wires from sharp edges by carefully routing them, always use rubber grommets to protect wiring and cables whenever you are installing them through metal openings.
• Secure all wiring using cable ties or wire clamps to protect them from moving parts and sharp edges.
• This apparatus shall not be exposed to dripping or splashing, and no object filled with liquids, shall be placed on the apparatus.
• Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as the power input terminals are damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.
•  Fuses shall be replaced only with the correct type and fuse value, and only when the apparatus is powered off.
•  Exposure to high sound pressure levels may lead to permanent hearing loss. Take every precaution to protect your hearing.
• This product is designed specifically for use with 12 volt, negative- ground electrical systems only. Using this product in systems with positive ground and/or voltages other than 12V may result in damage to the product and your system.

TOUCH BUTTON FUNCTION INTRODUCTION

1. Volume+: long press to increase volume continuously;
   short press to increase volume by step.

2. Volume-: long press to decrease volume continuously;
   short press to decrease volume by step.

3.  Power: when the screen open, short press into mute mode,short press once agian to unmute;long press to close the screen; when the screen close and ACC&B+ ON, short press to open the screen.

4.  Home: Press to enter main menu.

5.  Voice Recognition:Press to active Siri/ AA voice function.

REMOTE CONTROL INTRODUCTION

1.  Long Press:
   Short Press:Mute / Unmute.

2.  Short Press:CP/AA/BtPhone – Answer a call.

3. Short Press:CP/AA/BtPhone – Hang up the phone.

4. Short Press:Enter the CP/AA interface.

5. Short Press:Enter the AV-IN interface.

6. Short Press:Enter the Radio interface.

7.  Short Press:Enter the SD interface.

8. Short Press:Enter the BTphone interface.

9. Short Press:Enter the USB interface.

10. Short Press:lncrease volume.

11. Short Press:Reduce volume.

12.  Short Press:

    • USB/SD – Next track.
    • CP/AA/BTphone – Next track.
    • Long Press:Radio – Automatic seek (forward).
    • USB/SD – Fast forward.

13.  Short Press: Radio – Switch to the previous preset.

    • USB/SD – Previous track.
    • CP/AA/BTphone – Previous track.
    • Long Press: Radio – Automatic seek (reverse).
    • USB/SD – Fast reverse.

14. Short Press:CP/AA – Move the cursor.
    RADIO – (left / right)Frequency step function.

15. . Short Press:CP/AA – Select the function.
    Radio/USB/SD – Confirm the number entered.

16. Short Press:Enter the setting interface and click again to
    enter the current mode.

17. Short Press: Enter the EQ interface and click again to enter the current mode.

18.  Short Press:Play_pause.

19. . Short Press: Radio – When the input keyboard is not displayed;press the 1- 6 keys, the short press function is to switch to the corresponding (1-6) radio station, and the long press function is to save the corresponding (1-6) radio station frequency. In the case of input keyboard display, the function of 0-9 keys is to input the corresponding number (0-9) Bt Phone – Input the content(long press “O” indicates the input “+”)

FUNCTIONS APPLICATION

Basic Operations

Main Menu
Please refer to the actual menu display for reference.
During initial power on, the unit will show the languages setting interface, select the required country and language, then press “✓” to enter the main menu.

• Radio: Shows the Radio interface.

• Phone: Shows the Bluetooth connection interface.

• Android Auto/CarPlay:
  Shows the relevant interface based on your connected device.

• USB: Shows the USB playback
  interface for compatible files.

• Music: Shows the music playback  interface.

• Card: Shows the TF Card interface, enabling playback for compatible files.

• camera: Turn on the front camera.

• Setup: Shows the Settings interface.

• AV-In: Shows the AUX interface.

• Screen off: Turns off the screen, to reactivate the screen simply press any part of the screen.

Radio
Touch “Radio” in the main menu to enter the radio interface.

• To return to the main menu.
• Switch between FM 1 /FM2/FM3 I AM 1 / AM2.
• Enter the EQ settings interface.
• Turns the LOC function on/off.
• ( Shows the Radio tuning  input interface, input the frequency directly or selected preset stations to start playing.
•  Scans for available stations, long press to automatically search and save stations with the strongest signals into the presets.
• Scans for stations in reverse. Long press to search for stations automatically.
• Scans for stations.Long press to search for stations automatically

RDS Function
RDS will allow you to display information such as traffic status, radio station name and more. The unit can automatically switch to the strongest station based on the similar program.

• AF: Turn on/off AF mode.
• TA: Turn on/off TA mode.
• PTY: Shows program types, and allows you to search for stations according to different programs.

Phone
This unit allows for hands free calling, using your phone’s Bluetooth connection to the unit, you’ll be able to dial, answer, access phone book and playback music.  Enter the Bluetooth interface using the Bluetooth button.

• Dial
•  Calls record
• Phone book
• Setup

Pair/Connect
Connect your phone to the unit using the below steps.

1. Access the Bluetooth connection interface in your phone.
2.  Search for Bluetooth devices from either the unit or phone.
3.  Once connected successfully, the will be a prompt for the password. Input “0000” to confirm the connection.

Dial
Once the phone and unit are connected successfully, you’ll be able to make calls from the unit.

• Touch to make a call.
• Touch to delete numbers one by one, long press to delete all inputted numbers.
• Touch to show the numbers keyboard, touch again to exit.
• Touch to hang up the call.
• Touch to switch call audio  to earphone/ AV receiver.
• Touch U to mute.

Note: You can also manage calls through your phone.

Calling Record
Check for dialed/answered/ missed calls history. Touch icon to enter calling record interface:

Delete dialed calls.

Phone Book

When your phone and unit are paired, the unit can automatically reach contacts from your phone and store them within the unit.
(selected phones only)

Delete Contacts.

External Play Device
When you connect a compatible data device to your unit, the following interface will appear.

1. USB List Menu

2.  Play previous song/media

3. Play/pause current song/media

4. Please next song/media

5. Repeat mode
   Repeat all – Repeat off – Repeat single

6. Random playback on/off

7. Next page

8. EQ settings

9. Numbers selection playback

Music
Touch to enter music interface. EQ is the same as sound settings EQ menu.

Lossless files playback supported. FLAC/WA V / APE file formats.

Settings Operation
Touch “Setting” icon from main menu to enter the settings interface.

Time Setting
Touch “time” to enter time setting Up/down sliding can set year/ month/date/hour/minute/time system.
Time zone: Touch the Time icon to enter the time zone settings. Up/Down sliding to scan different time zones, select the correct one required.

Sound Setting
Touch “Sound Setting” to enter sound setting interface:

In sound setting menu, you can turn on/off keyboard sound/GPS monitor function/GPS mix sound/ reverse sound/EQ.

EQ: Touch EQ icon to enter below menu:

• Enter sound focus control function.
• Fine adjustment
• Fast set sound focus’s control point.
• Up/down slide to switch EQ modes: rock/classical/jazz/etc.
• Set sound delay.
•  Reset to default settings.

General Setting

Touch To set relevant functions on/off . More items can be accessed by sliding the menu.

• Brightness : Left and right slide

• icon to adjust screen’s brightness.

• Video Control:
  Click icon to turn ON/OFF the  Drive-forbidden-Watch Video.

• PAC:
  Touch the icon to set PAC on/off.

• SWC:
  Touch “SWC” icon to enter  the steering wheel control menu. wheel control menu.

• Radio Area:
  Choose the required. radio region.

• Serial/Version:
  Touch [Serial & Version] icon to enter serial number and verison number interface,  to check the needed information.  (Please refer to the actual unit display)

• Language:
  Touch [Language] icon to enter language setting interface,

select the required language.
Reset Factory Data
Once selected, the unit will prompt to confirm reset to factory settings. Once confirmed the system will automatically reboot. All data will be lsoot and any third party programs will be lost. Please backup your data before performing this function.

MIC Switch:
Touch F/R icon to change front or rear mic.

Wallpapers Setting
Choose the required wallpaper, touch “wallpaper setting” icon  to enter the setting interface.

AUX In
Insert video input connector to input video’s input jack, audio input conencto to input audio’s input jack, touch “AUX-IN” icon from main menu to enter the AUX interface.

Android Auto/CarPlay
Connect Phone t  the Android Auto interface.

The unit can be used to call,  play music, view maps, check traffic information, watch videos, return to the unit’s main interface, listen to Podcasts, read Audiobooks and so on.  Connect iPhone to the unit to enter the CarPlay interface.

The unit can be used to make calls, play music, view maps, check traffic information, watch videos, return to the unit’s main interface, listen to Podcasts, read Audiobooks and so on.

COMMON TROUBLE-SHOOTING

FUNCTIONS APPLICATION

Warnings:
Warranty void if this unit is damaged due to misuse or unauthorized service attempt.  Before making any electrical connection, disconnect the vechicle battery’s negative terminal. Refer to manual for installation.  Connect each pair of speaker leads only to a single pair of speakers (or speaker system) that has an impedance of at least 4 ohms, as well as SO-watt power-handling capability.  Never allow the uninsulated part of any speaker leads to touch the metal part of the vehicle.  Connect speaker leads to input of external amplifier ONLY if indicated in amplifier manual, otherwise this unit’s internal amplifier will be damaged

PRECAUTIONS ON POWER SUPPLY AND SPEAKER CONNECTIONS:

Do not connect the speaker leads of the power cord to the car battery; otherwise,the unit will be seriously damaged.
BEFORE connecting the speaker leads of the power cord to the speakers, check the speaker wiring in your car.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>