FEIT Electric UCL/REMOTE Under Cabinet Handheld Wireless Remote Installation Guide

: June 7, 2024
: Feit Electric

Table of Contents

Safety Information
FCC STATEMENT
Limited Warranty
Pre-Assembly
Screw Mount Installation
Adhesive Mount Installation
Operating Instructions
Mounting Template
Documents / Resources

UNDER-CABINET HANDHELD REMOTE
IMPORTANT SAFETY INSTRUCTIONS
AND INSTALLATION GUIDE
Model: UCL/REMOTE2 FEIT Electric UCL REMOTE Under Cabinet Handheld Wireless
Remote

READ BEFORE INSTALLATION
SAVE THESE INSTRUCTIONS
Questions, problems, missing parts? Before returning to the store, call Feit Electric Customer Service
8 a.m. – 5 p.m., PST, Monday – Friday
1-866-326-BULB (2852)
FEIT.COM

We appreciate the trust and confidence you have placed in Feit Electric through the purchase of this Under Cabinet Remote. We strive to continually create quality products designed to enhance your home. Visit us online to see our full line of products available for your home improvement needs.
Thank you for choosing Feit Electric.

SAVE THESE INSTRUCTIONS

Safety Information

IMPORTANT SAFEGUARDS:
ALWAYS FOLLOW BASIC SAFETY PRECAUTIONS WHEN USING ELECTRICAL PRODUCTS, ESPECIALLY WHEN CHILDREN ARE PRESENT.

CAUTION : Do not install this product in a wet location.
CAUTION: Do not install this product in an outdoor location.
CAUTION: Do not use chemical solvents or harsh abrasives to clean the ﬁxture.

FCC STATEMENT

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the quipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Any changes or modiﬁcations not expressly approved by the manufacturer could void the user’s authority to operate the equipment. Feit Electric Company, 4901 Gregg Road, Pico Rivera, CA 90660. www.feit.com, 1-800-543-3348.

Limited Warranty

This product is warranted to be free from defects in workmanship and materials for up to 1 year from date of purchase. If the product fails within the warranty period,please contact Feit Electric at info@feit.com, visit feit.com /contact-us or call 1-866 326-BULB (2852) for instructions on replacement or refund. REPLACEMENT OR REFUND IS YOUR SOLE REMEDY. EXCEPT TO THE EXTENT PROHIBITED BY APPLICABLE LAW, ANY IMPLIED WARRANTIES ARE LIMITED IN DURATION TO THE DURATION OF THIS WARRANTY. LIABILITY FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES IS HEREBY EXPRESSLY EXCLUDED. Some states and provinces do not allow the exclusion of incidental or consequential damages, so the above limitation or exclusion may not apply to you. This warranty gives you speciﬁc legal rights, and you may also have other rights which vary from state to state or province to province.

Pre-Assembly

TOOLS REQUIRED

FEIT Electric UCL REMOTE Under Cabinet Handheld Wireless Remote - TOOLS
REQUIRED

HARDWARE INCLUDED
NOTE: Hardware not shown to actual size.

FEIT Electric UCL REMOTE Under Cabinet Handheld Wireless Remote - HARDWARE
INCLUDED

Part	Description	Quantity
AA	Handheld Remote	1
BB	Mounting Plate	1
CC	Mounting Screw	2
DD	Mounting Guide	1
EE	3M Tape	2

DEVICE COMPATIBILITY LIST (Max 100 paired units)

UCL12/5CCT
UCL24/5CCT
UCL36/5CCT
UCL12FP/5CCTCA
UCL18FP/5CCTCA
UCL24FP/5CCTCA
BPUCUPUCiU5CCT/3
UCL192/FLEX/5CCT

Screw Mount Installation

Position the Remote
Find the desired location for the Mounting Plate (BB) and mark clearly using the provided Mounting Guide (DD).
NOTE: The Mounting Plate can be installed horizontally or vertically.
Separate the Mounting Plate
Carefully separate the Mounting Plate (BB) backplate.
Installing Mounting Plate
Screw in the backplate of the Mounting Plate (BB) using Mounting Screws (CC) on the marked location.
Installing Mounting Plate
Snap the front of the Mounting Plate (BB) onto the mounting backplate.
Attach the remote to the Mounting Plate
Attach the Handheld Remote (AA) to the metal Mounting Plate (BB) via the magnet on the back of the Handheld Remote (AA).

Adhesive Mount Installation

Install 3M Tape on Mounting Plate
Remove one side of the adhesive backing paper on the 3M Tape (EE) and place it in the indents on the back of the Mounting Plate (BB).
Install the Mounting Plate
Remove the adhesive backing paper on the 3M Tape (EE) and place it on the wall at the desired location.
Attach the remote to the Mounting Plate
Attach the Handheld Remote (AA) to the metal Mounting Plate (BB) via the magnet on the back of the Handheld Remote (AA).

Operating Instructions

FEIT Electric UCL REMOTE Under Cabinet Handheld Wireless Remote - Operating
Instructions

Initial Remote Recognition
The ﬁrst time pairing ﬁxtures to the remote requires that the ﬁxtures recognize the speciﬁc remote. Power on the ﬁxture & hold the ON/OFF button on the remote for 3 seconds. Lights will blink once the units have recognized the remote. This can be done with multiple ﬁxtures at once.

Pair or Unpair Fixtures to the Remote

To pair a ﬁxture to the remote, power on the ﬁxture and hold the Dim button on the remote for 3 seconds. Lights will blink once the units are paired. This can be done with multiple ﬁxtures at once.
To unpair a ﬁxture from the remote, power on the ﬁxture and hold the ON/OFF button on the remote for 3 seconds. Lights will blink once the units are unpaired. This can be done with multiple ﬁxtures at once. When unpaired this way, LED ﬁxtures will be reset to the default mode of operating individually.

Changing the Dimming Levels

To select the desired dimming level, Cycle through Dimming levels (High, Medium, Low, Dim, Off) by pressing the Dim Button. This setting will be ﬁxed each time the ON/OFF switch is turned ON.

Changing the Color Temperature Setting

To select the desired color temperature, cycle through 2700K – 3000K – 3500K – 4000K – 5000K by pressing the CCT Button. This setting will be ﬁxed each time the ON/OFF switch is turned ON.

NOTE: Once paired, to operate a ﬁxture separately from the remote, hold the CCT button for 3 seconds on the ﬁxture that you want to control independently. This ﬁxture will not respond to the remote and can only be operated individually through the buttons on the ﬁxture. Press and hold the CCT button for 3 seconds on the ﬁxture again to reconnect to the remote.