FEIT Electric STRP/2X1/4WY/LED Dual Lamp Color Selectable LED Strip Light Instruction Manual
- June 7, 2024
- Feit Electric
Table of Contents
FEIT Electric STRP/2X1/4WY/LED Dual Lamp Color Selectable LED Strip Light Instruction Manual
Questions, problems, missing parts? Before returning to the store,
call Feit Electric Customer Service
8 a.m. – 5 p.m., PST, Monday – Friday
1-866-326-BULB (2852)
FEIT.COM
We appreciate the trust and confidence you have placed in Feit Electric
through the purchase of this LED Strip Light. We strive to continually create
quality products designed to enhance your home. Visit us online to see our
full line of products available for your home improvement needs.
Thank you for choosing Feit Electric.
Important Safety Information
For your safety, always remember to:
- Turn off the power supply at the fuse or circuit breaker box before you install the fixture.
- Ground the fixture to avoid potential electric shock and to ensure reliable starting.
- Double-check all connections to be sure they are tight and correct.
- Wear rubber soled shoes and work on a sturdy wooden ladder.
- Account for small parts and destroy packing material, as these may be hazardous to children.
These products may present a possible shock or fire hazard if improperly installed or attached in anyway. Products should be installed in accordance with the owners manual, current electrical codes and/or the current National Electric Code (NEC).
FCC STATEMENT
Supplier’s Declaration of Confinity: 47 CFR § 2.1077 Compliance Information
Responsible Party: Feit Electric Company 4901 Gregg Road, Pico Rivera, CA
90660, USA 562-463-2852
Unique Identifier: STRP/2X1/4WY/LED
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radian technician for help. Any changes or modifications not expressly approved by the manufacturer could void the user’s authority to operate the equipment. CAN ICES-005 (B).
SAVE THESE INSTRUCTIONS
CAUTION: Turn off the main power at the circuit breaker before installing the fixture in order to prevent possible shock.
CAUTION: Do not use or store in a corrosive environment with hazardous materials, e.g. Sulphur, Chlorine, Phthalates, etc.
NOTICE: All electrical connections must be in accordance with local and National Electrical Code (N.E.C) standards. In you are unfamiliar with proper electrical wiring connections, obtain the services of a qualified electrician.
CAUTION: Do not install on a radiant-heating ceiling.
NOTICE:
- Suitable for damp locations
- Maximum ambient operating temperature: 104°F (40°C)
Limited Warranty
This product is warranted to be free from defects in workmanship and materials for up to 5 years from date of purchase. If the product fails within the warranty period, please contact Feit Electric at info@feit.com, visit feit.com/contact- us or call 1-866 326-BULB (2852) for instructions on replacement or refund. REPLACEMENT OR REFUND IS YOUR SOLE REMEDY. EXCEPT TO THE EXTENT PROHIBITED BY APPLICABLE LAW, ANY IMPLIED WARRANTIES ARE LIMITED IN DURATION TO THE DURATION OF THIS WARRANTY. LIABILITY FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES IS HEREBY EXPRESSLY EXCLUDED. Some states and provinces do not allow the exclusion of incidental or consequential damages, so the above limitation or exclusion may not apply to you. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state or province to province.
Pre-Installation
TOOLS REQUIRED
HARDWARE INCLUDED
NOTE: Hardware not shown to actual size.
Assembly
1 Turn the power OFF at the switch and fuse box or the circuit breaker.
2 Open the fixture (AA) carefully (see Fig.1 ).
3 Use a screw driver to pop open your desired knockout on your fixture. Install 1/2 in. conduit fitting (not included) as appropriate.
4 Lift the fixture (AA) up against the ceiling at the desired installation location. Use a pencil to mark at the key holes where the plastic anchors (BB) will be located (see Fig. 2).
5 Use a small drill bit to drill 1/4 in. Pilot hole where you marked, then insert the wall anchors if needed. Screw in provided mounting screws (CC) on plastic anchors, leave 1/4 in. of screw out.
6 Install the fixture (AA) to the mounting surface by aligning the key holes to the mounting screws (CC). Shift the fixture (AA) to the narrow side of the keyhole to lock-in place (see Fig.’s 4 and 5). Tighten the Mounting screws (CC) to secure the fixture (AA) to the mounting surface.
NOTE: The ground wire will be used as a safety wire to hold the lens up during the installation.
7 Connect the wire coming from the fixture to the wires coming from J-box using wire connectors (DD) (see Fig. 6). (Black – Line Voltage, White – Neutral, Green- Ground/Bare Copper)
8 Select desired color temperature using the slide switch on the driver (3OOOK, 4OOOK, or 5OOOK) upon installation or select “SWITCH” to control by wall switch (see Fig. 7).
9 Close the fixture then turn on the power at fuse or circuit breaker.
Color Changing Instructions
-
You can lock in one color temperature, change among multiple color temperatures, it will memorize the last color temperature and reset automatically.
-
Soft White – Bright White – Daylight – Light Switch Marks on the lamp: SW-BW-DL-Switch.
-
When the slide switch is set to SW (Soft White), the color temperature fixes at 3000K.
-
When the slide switch is set to BW (Bright White), the color temperature fixes at 4000K.
-
When the slide switch is set to DL (Daylight), the color temperature fixes at 5000K.
-
When the slide switch is set to SWITCH, the color temperature can be changed from SW-BW-DL with your existing light switch.
-
To change color temperatures using your existing light switch:
A. Set the slide switch on the back of the fixture to “SWITCH”
B. Toggle your light switch ON and OFF within 0.5-3 seconds to cycle through the 3 different color temperatures.
C. If the fixture is left ON for over 10 seconds then turned OFF, the fixture remembers the last color temperature selected and displays that color when turned on again. -
The reset function is used when using multiple Color Selectable lighting products operating from the same light switch. In the event multiple fixtures are not displaying the same color at the same time, fixtures must be RESET using your existing light switch. Simply toggle the wall switch ON and OFF seven times quickly. For best results, cycle ON/OFF 7 times within 5-10 seconds.
Fixture Maintenance
- Please make sure the power is off before maintenance by turning the breaker off or removing the fuse from the fuse box.
- To avoid any damage to the product, please do not use any chemical solvents during the routine maintenance.
- Do not use liquid cleaner on the LEDs, LED driver or wiring inside the light fixture.
- To ensure better lighting, please clean the lamp periodically with a soft cloth.
WWW.FEIT.COM
Please contact 1-866-326-BULB (2852) for further assistance
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>