FEIT Electric LEDR4/RGBW/AG 11.1W LED Recessed Downlight Instruction Manual
- June 7, 2024
- Feit Electric
Table of Contents
ITEM # LEDR4/RGBW/AG
Thank you for your purchase. Questions, comments, or feedback? We’d love to
hear from you.
Visit feit.com/help for support.
INSTALLATION & OPERATING INSTRUCTIONS
READ & SAVE IMPORTANT SAFETY INSTRUCTIONS
Please read and understand this entire manual before attempting to assemble,
operate or install this product. This product must be installed in accordance
with any applicable installation code(s) by a qualified electrician or person
familiar with the construction and operation of the product and the hazards
involved.
WARNING
- RISK OF FIRE OR ELECTRIC SHOCK: The electrical rating of this product is 120VAC.
- RISK OF FIRE OR ELECTRIC SHOCK: Install this product only in luminaires that have the construction features and dimensions shown in the photographs and/or drawings in this manual.
- To prevent wiring damage or abrasion, do not expose wiring to edges of sheet metal or other sharp objects.
- RISK OF SHOCK — DISCONNECT POWER BEFORE INSTALLATION
- Do not make or alter any open holes in an enclosure of wiring or electrical components during installation.
- THIS DEVICE IS NOT INTENDED FOR USE WITH EMERGENCY EXITS.
- RISK OF FIRE OR ELECTRIC SHOCK: LED Recessed Downlight with Trim installation requires knowledge of luminaires electrical systems. If not qualified, do not attempt installation. Contact a qualified electrician.
CAUTION
To avoid possible electrical shock, be sure that the power supply is turned
off at the fuse box or circuit breaker before installing or servicing the
product. For your safety, read and understand the instructions completely
before beginning installation.
LIMITED WARRANTY.
This product is warranted to be free from defects in workmanship and materials
for up to five years from the date of purchase. If the product fails within
the warranty period, please visit feit.com/help for instructions on
replacement/refund or call 866.326.BULB. REPLACEMENT OR REFUND IS YOUR SOLE
REMEDY. EXCEPT TO THE EXTENT PROHIBITED BY APPLICABLE LAW, ANY IMPLIED
WARRANTIES ARE LIMITED IN DURATION TO THE DURATION OF THIS WARRANTY. LIABILITY
FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES IS HEREBY EXPRESSLY EXCLUDED. Some
states and provinces do not allow the exclusion of incidental or consequential
damages, so the above limitation or exclusion may not apply to you. This
warranty gives you specific legal rights, and you may also have other rights
which vary from state to state or province to province.
Supplier’s Declaration of Conformity: 47 CFR § 2.1077 Compliance
Information
Responsible Party: Feit Electric Company 4901 Gregg Road, Pico Rivera, CA
90660, USA 562-463-2852
Unique Identifier: LEDR4/RGBW/AG This device complies with part 15 of the
FCC Rules. Operation is subject to the following two conditions: (1) This
device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired
operation. Note: This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures: Reorient or relocate
the receiving antenna. Increase the separation between the equipment and
receiver. Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected. Consult the dealer or an experienced
radio/TV technician for help. Any changes or modifications not expressly
approved by the manufacturer could void the user’s authority to operate the
equipment. CAN ICES-005 (B)
PACKAGE CONTENTS
Before beginning the installation of this product, make sure all parts are present. Compare parts with package contents list and diagram. If any part is missing or damaged, do not attempt to assemble, install or operate this product.
| COMPONENTS INCLUDED
---|---
A
|
(1) MEDIUM BASE ADAPTER
B
| (1) RECESSED DOWNLIGHT
C
| (1) INSTRUCTION MANUAL
PRODUCT ELECTRICAL RATINGS
120 V / 60 Hz, XX mA, 8 W
WET LOCATION LISTED, ACCEPTABLE IN SHOWER INSTALLATIONS.
Suitable for Type IC Housings and Non-IC Housings.
MINIMUM LAMP COMPARTMENT DIMENSIONS:
4 in. (102 mm) DIA X 5.5 in. (140 mm) HEIGHT
INSTALLATION INTO EXISTING RECESSED FIXTURE
NOTE: For use with 4 in. recessed housings (housing sold separately)
-
Turn off the power at the switch and fuse box or circuit breaker.
-
Remove the existing trim installed in the recessed housing (if necessary).
-
Install the medium base adapter into the socket.
-
Connect the two terminals together.
-
Squeeze the dips in and gently push the product into place.
-
Gently push the product in until it is flush to the ceiling.
Need Help?
Thank you for your purchase.
Questions, comments, or feedback?
We’d love to hear from you.
Visit feit.com/help for support or connect with us:
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>