ZiGMA Aerio-300 Air Purifier User Manual

USER MANUAL
Zigma Air Purifier
Model: Aerio-300

Warnings:

• This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

• Note: The Grantee is not responsible for any changes or modifications not expressly approved by the party responsible for compliance. such modifications could void the user’s authority to operate the equipment.

• Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
  — Reorient or relocate the receiving antenna.
  — Increase the separation between the equipment and receiver.
  — Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  — Consult the dealer or an experienced radio/TV technician for help.

• The device has been evaluated to meet general RF exposure requirements. To maintain compliance with FCC’s RF exposure guidelines, this equipment should be installed and operated with a minimum distance of 20cm between the radiator and your body.

• Clean UV-C surface every 6 months or when light transmittance is less than 60%. Disconnect the power supply before cleaning.

• The following information is required to use the product:
  — This appliance contains a UV-C emitter.
  — Unintended use of the appliance or damage to the housing may result in the escape of dangerous UV-C radiation. UV-C radiation may, even in little doses, cause harm to the eyes and skin.
  — Appliances that are obviously damaged must not be operated.
  — The replacement of the UV-C emitter is not allowed.

Maintenance – Attention

Be sure to hold the plug and unplug the power cord; when not in use for a long time.
Do not place in such places:

• Unstable places. (Otherwise, it may fall over and cause injury)
• A place of high temperature, high humidity, or easy to get wet. (to prevent leakage accidents)
• Kitchen or other places where soot is emitted.
• A place with lots of oil, combustible gases, or where leakage may occur.
• A place with animals or plants (In order to prevent air-dried animals and plants)
• Corrosive gas and metal dust sites.

Do not let volatile substances or combustible substances into the machine. (Otherwise, it could lead to a fire accident)
Do not use the air purifier in the room with fumigated insecticide. (The chemical residue accumulates inside the machine and may be released from the outlet and endanger health)
Do not wet the outlet and the body part. (Otherwise, may cause fire or electric shock accident)
Keep the air in circulation when using it together with a heating furnace or heater.
Please close the doors and windows when using.
Do not use gasoline, chemicals, and other solvents to wipe. Do not spray insecticide.
Do not sit or lean against the air purifier. (Otherwise, it may cause damage to the air purifier)
Do not shake the air purifier. ( Otherwise, it may cause the air purifier sensor disorder) 0 Air purifiers should be stored in dry, ventilated, non- corrosive, and explosive areas.
Leave at least 60cm of space between the air inlet and the wall.

Maintenance – Install the filter

Thanks for purchasing the Zigma air purifier. Before using, please install the unit correctly according to the following 4 steps to ensure that the air purifier is installed and placed properly, then connect it to a power source.

1. Pull the rear cover handle to remove the filter.
   

2. Remove the plastic package from the filter.
   

3. Install the filter into the air purifier.
   

4. Put into the top part of the air inlet ..„, firstly, then push the Rib lower part “b. inward. The grille is installed correctly after hearing a “click”
   

Filter replacement period:
Based on the lab test data, the filter expiry period is 6-9 months.
Tips:

• Depending on the real use environment and different methods of use, the filter replacement time will be different
• Please treat the replaced filter as non-flammable garbage.

**Product introduction

**

|
---|---

**Control Panel

**

• The light rings indicate the air quality during the filter’s lifetime. When the filter is expired, the light ring will blink red as a reminder
  

How to use

O n/off button

• On/off: Tap this button to turn on the air purifier, the default is speed 1.
• Fan speed shift: Tap this button and the fan speeds Cycles through”speed1, speed 2, speed 3, auto, off ” the corresponding fan speed indicator lights up. Auto mode: In the auto mode, the machine determines the fan speed according to the air quality. Manual mode: The air purifier will run according to the set fan speed, such as 1/2/3.
• Wi-Fi net pairing: Please download the “Zigma” App first, referring to the instruction on the next page, add equipment, and complete network configuration to download and pair the device

Sleep/Child lock button

• Sleep: Tap this button, to turn Sleep Mode on/off. Sleep Mode operates quietly by using the lowest possible fan speed, all indicators except the sleep indicator will be off. Tapping any key, the display will resume for 30 seconds and then tap any key again within 30 seconds to exit sleep mode and enter the auto mode. After 30 seconds without button operation, the display will be off.
• Child locks: Press and hold this button for 3 seconds to enter or exit the child lock. After entering the child lock state, other key functions are no longer performed, if there is a key operation, all indicator lights flicker twice (ring lights flicker blue), but do not perform the function of the operation. If you do not want to exit the child lock state but want to operate other functions, you can control through the APP.

Negative ion/UV-C/Filter

• Filter: when the filter life expires, the air quality ring will blink red as a reminder. In the boot state, long-press the button and hold for 5 seconds, after the beep, the light ring will flash red 3 times, filter life is then reset.
  After the filter expires, the air purifier can still run for up to 168 hours before shutting off automatically. After expiry, it cannot be turned on until replacing and resetting the filter.

Zigma App Instructions
1. Download and install the “Zigma” App
Scan the QR code below, or search “Zigma” at Google Play or the Apple app store to download and install Zigma App.

https://www.grit- cfg.com/app/Zigma/rel/download/download.html
Zigma

2. Sign up / Log in
Sign up/log in to your Zigma account.
3. Add devices to the App
3.1 Scan the QR code on the device to add the device 3.2 Select Wi-Fi network and enter a password
(Note: the device currently do not support 5G networks)
3.3 Wi-Fi Settings
Select 2.4 GHz Wi-Fi and Enter the Correct Password
(Currently don’t support 5GHz Wi-Fi)
3.4 Reset device

1. Press the power switch to restart the device.
2. Press and hold the power button for 3 to 5 seconds, until you hear a “beep” from the device.

Troubleshooting

The following problems you may encounter during your use. If you can not solve the problem according to the information below, please contact the local dealer.

Problem| Checking|

Possible Solution

---|---|---
An air purifier will not turn on or respond to button controls.| Check to see if the power on| Switch on
Check to see if the power outlet lose| Power on
Check to see if the filter cover is installed properly| Install once again
The air purifier sounds dull, and the airflow is significantly reduced| Make sure the filter is removed from its packaging and properly in place| Remove the filter packaging and install the filter
Make sure there is at least 60cm of clearance on all sides of the air purifier.| Turn off the air purifier and remove any obstructions
Strange smell coming from the purifier.| Check to see if a large amount of odor is released continuously around the air inlet.| Remove the odor, and run the purifier for a while
Check to see if the filter life has expired| Clean the filter and replace it if necessary.

Packing list

Specification

**Warranty card

**

Note:  Thank you for choosing Zigma products!  To protect your legal rights, please save this card!  Please fill in this card when the product needs to be repaired.
Maintenance records 1

Address:

Maintenance records 2

Address:

Maintenance records 3

Address:

Certificate of Quality

E-mail: support@zigma.co
Facebook: https://www.facebook.com/zigmasmarthome/
Web: www.zigma.co

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>