Tempo VT3 Lite Smart Watch User Manual
- June 7, 2024
- Tempo
Table of Contents
Tempo VT3 Lite Smart Watch User Manual
WHAT’S INCLUDED
PRODUCT OVERVIEW
GETTING STARTED
1. Charge Your Watch
Note:
- Please fully charge your smart watch before the first use.
- If the Charging Cable can not be magnetically attached on the Charging Pins of the watch, please change the direction of it.
2. Wear Your Watch
- To make the data tracking more accurate, we recommend that you wear the watch with one finger’s width below your wrist bone.
- Please make sure the watch fits snugly against your skin and will not move upward or downward during exercise.
3. Change the Watch Bands Optional
Step 1:
Turn over your watch, then press the quick-release lever inward and gently
pull the original watch band away.
Step 2:
Get another band, slide the pin into the notch on the watch, then press the
quick-release lever inward and slide the other end of the watch band into
place.
Step 3:
Release the quick-release lever when the pins on both ends are securely
inserted into the notch. 4.Power On/Off
Long press the Power Button for 3-4 seconds to power on the watch, then
select your language. To power it off, long press the Power Button for 2-3
seconds and tap Shutdown on the screen.
- Functions of the Power Button
5.Touch Navigation Tap
OPERATION BASICS
1. Function Overview on the Watch
- Swipe up from the bottom of the home screen to check Music, Calories, Stand, Steps and Reading.
- Swipe left/right on the home screen to check the applications and 18 available exercises on your watch.
HR
Perform a heart rate test to monitor your heart rate. Note:
Battery drains faster while running the HR application.
Message
Display messages your phone received after Bluetooth is connected.
Alarm
Screen on and vibrate to notify you at the preset time of the alarm set via
the app.
Stopwatch
Measure the amount of time, and tap Lap to track the number of laps when
needed.
Compass Hold the watch horizontally to identify the direction.
Timer
Select a time interval or customize new time interval(s), then count down from
that time interval.
Settings
Tap to change the watch face, adjust the brightness, check the Bluetooth name,
the version of your watch and reset the watch.
2. Operate via VIRMEE App
We’ll update the user manual according to the latest app version of VIRMEE,
please visit www.virmee.com to get the latest
instructions.
(1) Download and Install the App Search and download VIRMEE App from APP Store/Google Play or scan the QR code directly.
https://qrs.ly/qlblyfdhttps://qrs.ly/zmbyxps
(2) Pair the Watch with Your Mobile Phone
Step 1: Turn on your watch, slide left/right to select Settings, then tap
About to check the Bluetooth name of the watch.
Step 2: Enable Bluetooth on your mobile phone.
Step 3: Launch VIRMEE on your mobile phone and register an account.
Step 4: Follow the in-app instructions to create your profile.
Step 5: Tap Device >+> SEARCH AGAIN on your mobile phone, then tap
VIRMEE_ XXXX to connect.
Notes:
- If you have an Android phone, please permit the watch to access your location, otherwise the watch may not be searched.
- Please give full permissions to the watch to sync the information, otherwise the app may fail to display all the available options.
- The watch can only pair with one mobile phone at a time.
(3) Function Overview on the App
Tap Device on your mobile device to know more functions of your watch.
Change Dial
Tap to customize and change your watch face.
Alarm
Tap to add/manage alarm clock(s).
Sedentary reminder
Tap to set a sedentary reminder when you sit for too long.
Smart reminder
Tap to enable/dyable the access to the notifications of Call ID/SMS/other
applications.
Easy camera
Enable it, then tap the watch to take a photo and save it to your device.
Time format
Switch time format between 12h and 24h.
Date format
Switch date format between Month/Day and Day/Month.
Unit of measurement
Set measurement unit when exercising(Run, Fast Walk, and Pool Swim).
Language switch
Change the language of your watch. Please tap Save on the top right corner if
the language is selected.
Vibration remind
Set vibration reminder and cycles for call, alarm, sedentary, and more.
Palming gesture
After enabling this function, the watch will screen on when you raise your
wrist at the set time period.
Bright screen time
Set a time period after which the watch will screen off.
Do not disturb
Select a time period during which the watch will mute sound and stop
vibration.
Auto-Heart rate
After enabling this function, the watch will test your heart rate every 10
minutes.
Heart rate guidance
Set a remind zone for different categories, the watch will vibrate when your
heart rate data is below or above the value you set.
Wearing manner
If you wear your watch on your right/left wrist, please select Right/Left;
wrong selection will lead to wrong data.
Auto-recognition motion
After setting it to ON, the watch will automatically recognize the exercise
you are doing and enter into the sport interface accordingly.
Firmware upgrade
Check the firmware version of your watch and update it when available
- Before you update the firmware version, please make sure the battery level is more than 50%.
- Please do not exit the update interface to avoid update failure.
IMPORTANT:
To get a better experience, we recommend that you update the firmware as soon
as you notice there is a newer version available.
Unbind
Tap to unbind the watch and stop sync data with your mobile device.
SPECIFICATIONS
MAINTENANCE AND CARE
FCC Caution
Any Changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
–Reorient or relocate the receiving antenna.
–Increase the separation between the equipment and receiver.
–Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
–Consult the dealer or an experienced radio/TV technician for help.
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment . This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
ISEDC Warning
This device complies with Industry Canada license-exempt RSS standard(s).
Operation is subject to the following two conditions:
(1) this device may not cause interference, and
(2) this device must accept any interference, including interference that may
cause undesired operation of the device.
The device is compliance with RF exposure guidelines, users can obtain Canadian information on RF exposure and compliance.
CAUTION: RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS. Do not use other unauthorized chargers power supply for charging. Do not use the product in environment below 0 or above 50 for charging.
The symbol indicates DC voltage
RECYCLING
This product bears the selective sorting symbol for Waste electrical and electronic equipment (WEEE). This means that this product must be handled pursuant to European directive 2012/19/EU in order to be recycled or dismantled to minimize its impact on the environment. User has the choice to give his product to a competent recycling organization or to the retailer when he buys a new electrical or electronic equipment. This product can be used across EU member states.
Use the product in the environment with the temperature between 0 and 50;
Otherwise, it may damage your Smart Watch. It can be operated under 2000m. For
the following equipment: Product Name: Smart Watch
Brand Name: VIRMEE Model: VT3 Lite Shenzhen Van Top Technology & Innovation
Co., Ltd. hereby declares that this [Name: Smart Watch, Model: VT3 Lite] is in
compliance with the essential requirements and other relevant provisions of
Directive 2014/53/EU. A copy of the EU Declaration of Conformity is available
online at https://doc.vantop.com/.
Lithium ion Battery:
Model: 481525
Voltage: 3.8V
DongGuan Golden CEL Battery Co., Ltd.
Add: No.11, Yinhu Industrial Park, JiaoYiTang Management Zone, TangXia,
DongGuan, GuangDong, China
VIRMEE SUPPORT
North America : support@virmee.com
United Kingdom : support.uk@virmee.com
日本 : support.jp@virmee.com
https://www.facebook.com/VirmeeOfficial/https://virmee.com/https://www.instagram.com/virmee_global/