Listener Pro LP-WS300S Soundbar User Manual

: June 7, 2024
: Listener Pro

Table of Contents

Packing List
Parameter
Connection
Function Description
Wireless Connection
Wired Connection
Automatic Standby
Wall Mount
The toxic and hazardous substances or elements
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Listener Pro LP-WS300S Sound bar

Packing List

Parameter

Model	LP-WS300S
Dimensions	H965.5L459W308mm
Speakers	Tweeter: 0.75inch*4

Connection

You’d better connect this sound bar to your tv by wires (Bluetooth transmission will cause some sound loss)
This sound bar, subwoofer and rear speakers are used for a matching set.

The 4-meter-long rear speaker cable is in the accessory box

Power on:

Connect the sound bar, subwoofer and rear speaker to the power supply separately, the sound bar’s screen displays “-“, the indicator lights of the subwoofer and rear speakers flash slowly.
Press the ”Power” button on the sound bar touch panel for 3s, or press the power button on the remote control, the host will be turned on and the screen shows the volume

When the first time of connection, manually pairing is needed to enable the 5.8G strong anti-interference wireless function, and it will be connected automatically the next time

Step 1: Press on the remote control for 5s, “PAIR” will be shown on Screen.

Step 2: Long press the button on the back of the subwoofer until the blue indicator light stop flashing and keep on at all times

Step 3: Long Press the button on the back of the Rear speaker untile the blue indicator light stop flashing and keep on at all times

After the sound bar, subwoofer and rear speakers paired successfully, the screen will be back to Vol displays.

Function Description

1. Ports

USB : Automatically identifies and plays tracks from a storage device.
COX : Connect to the COX OUT jack of the source device using a
coaxial cable.
Power : Connect to 100~240V power supply.
OPT : Connect to the OPT OUT jack of the source device using a optical cable.
AUX : Connect to the RCA jack of the source device using a 3.5 to RCA cable.

| Note: Please unplug the unit from outlet if it is not to be used. Please keep the power cable as close as possible to the outlet without obstruction.
---|---

2. Subwoofer

Flash Slowly: Wait for pairing
Light On: Paired
Off: Stand by

**3. Rear Speaker

**

**4. Display Screen

**

Sound effect: You can select from 3 sound modes, the icon will light up once enter the corresponding mode.
MUS : music mode
NEWS : news mode
MOV : movie mode
Volume: The volume level can be set between 1 and 30, 18~20 is advisable.
Shows audio input temporarily: Select the audio source through touch
screen or remote control, the screen will show audio input for 3s, and then back to volume.
Audio input: Select the audio source to input through touch screen or
remote control, the corresponding icon will light up once this audio
source enter successful.
BT : Bluetooth input
AUX : stereo aux input
OPT : digital optical input
COX : coaxial input
USB : USB input, the playback time will display on volume area

5. Operation (Touch screen)

6.Remote control

Wireless Connection

Turn on the device, touch the icon on the control panel or press the button on the remote control, the “BT” icon will flash slowly on the screen indicating the sound bar has entered paring mode.
Search for “Listener Pro 300S” on your Bluetooth device and then pair to the sound bar. The BT icon will illuminate, and the sound bar will make an audible beep to indicate the connection is complete.

Notes:
If your device asks for a password during the pairing process, please use “0000”
If you can’t find or pair to this Bluetooth, turn off the sound bar, then 5s later turn it on and try to connect by following the instructions above.
The sound bar can only pair to one device at a time, if you can’t pair your device , please check that no other device is already paired with the sound bar. A previously paired device will automatically reconnect.
Bluetooth connection range is 5-8m, but it will be shorter by some causes radio interference such as WIFI routers, induction cookers and smart air cleaners; too much Bluetooth your device paired and reserved .

Wired Connection

Plug into the power supply, the display screen will shown “-” which means the sound bar is standby mode (do not turn on until audio connection completed). There are four ways to connect the sound bar and the audio source: AUX, OPT, COX, USB. Select one according to the device you are trying to connect, the corresponding icon will light up once this audio source enter successful.

Automatic Standby

To save power and extend the working time of the speaker, it will automatically switch to Standby mode if there is no input signal for over 15 minutes., and will turn back on when an input signal is detected.

Wall Mount

Place it on the cabinet

Mount it on the wall (mount kit needed)

Installation steps

Important:
User research shows, most users prefer to place speakers on cabinet in order to keep the wall clean. The height of this speaker is only 60mm, which is very suitable for placing in front of the TV, so there is no mount kit in the package. Please contact us if you need mount kits

After-sales services and warranty

30-Day Return of Any Reason. You may return your undamaged product and packaging within 30 days, please return the unit in its original carton.
12-Month Warranty for Quality-Related Issues. If it is not quality-related, the customer must pay the return shipping costs and repair costs.
When after-sales service is needed, please send us these information according to this form.
If you have any questions or comments, please contact us at service@listenerpro.com or visit our website: www.listenerpro.com.

Name| | Email|
---|---|---|---
Country|
Purchase Date| | Order ID|
Fault Description|

The toxic and hazardous substances or elements

Part Name| Toxic or harmful substances or elements|
---|---|---
Lead Pb)| Mercury (Hg)| Cadmium (Cd)| Hexavalent Chromium (Cr(VI))| Pobrominated biphenyls ( PBB)| ( PBDE)
PCB part| X| 0| 0| 0| 0| 0
Plastic part| 0| 0| 0| 0| 0| 0
Metal part| X| 0| 0| 0| 0| 0
Speaker| 0| 0| 0| 0| 0| 0
Power adapter| X| 0| 0| 0| 0| 0

This form was prepared in accordance with the provisions of SJ/T 11364

O : Indicates that the content of the hazardous substance in all homogeneous materials of the part is below the limit requirement specified in accordance with the GB/T 26572.

X : Indicates that the content of the hazardous substance in all homogeneous materials of the part is exceeding the limit requirement specified in accordance with the GB/I 26572. There is no mature alternative solution that meets the requirements of RoHS

The numbers in this mark indicate that the environmental protection used period of the product under normal use is 10 years. Some components may also have an environmental protection use period indication, and the environmental protection use period is subject to the figures in the indication. Due to different product models, the product may not include all the above parts except the host, please refer to the product packaging.

Only suitable for areas below altitude of 2 000 m.

Only for use in non-tropical climates

Listener Pro Technology Co., Ltd.
Web: www.listenerpro.com
Email: service@listenerpro.com