behringer 112 DUAL VCO User Guide
- June 6, 2024
- Behringer
Table of Contents
Quick Start Guide
112 DUAL VCO
Legendary Analog Dual VCO
Module for Eurorack
Controls
- PW MOD IN – Accepts a voltage from another module to control the pulse width.
- VCO OUT – Send the VCO signal to one or two sources via 3.5 mm TS cables.
- WAVEFORM – Select pulse, triangle or sawtooth waveforms for the VCO.
- PULSE WIDTH – Adjusts the pulse width modulation based on the voltage received at the PW MOD IN jack.
- MOD MANUAL – Sets the ratio between the upper and lower portions of the pulse wave.
- SYNC OUT – Sends a synchronization signal via 3.5 mm TS cable.
- RANGE – Sets the pitch range of the VCO in octave steps.
- SYNC IN – Accepts a synchronization signal via 3.5 mm TS cable.
- WEAK/STRONG – Determines the accuracy of synchronization.
- PITCH – Fine-tunes the pitch.
- MOD LEVEL – Adjusts the level of the signal connected to the associated MOD IN jack.
- MOD IN – Accepts voltages that control or modulate the VCO pitch.
Power Connection
Installation
The necessary screws are included with the module for mounting in a Eurorack
case. Connect the power cable before mounting. Depending on the rack case,
there may be a series of fixed holes spaced 2 HP apart along the length of
the case, or a track that allows individual threaded plates to slide along the
length of the case. The free-moving threaded plates allow precise positioning
of the module, but each plate should be positioned in the approximate relation
to the mounting holes in your module before attaching the screws.
Hold the module against the Eurorack rails so that each of the mounting holes
are aligned with a threaded rail or threaded plate. Attach the screws partway
to start, which will allow small adjustments to the positioning while you get
them all aligned. After the final position has been established, tighten the
screws down.
Specifications
Pulse Width Input
Type| 2 x 3.5 mm TS jacks, DC-coupled
Impedance| 70 kO, unbalanced
Maximum input level| ±10 V1 4% per volt
VCO Output
Type| 4 x 3.5 mm TS jacks, DC-coupled
Impedance| 1 ko, unbalanced
Maximum output level| 10 V P-P
Frequency range with no external CV| 10 Hz to 500 Hz
Frequency range using external CV| 1 Hz to 30 kHz
Sync Input
Type| 2 x 3.5 mm TS jacks, DC-coupled
Impedance| 100 ko, unbalanced
Maximum input level| 10 V P-P
Minimum input to trigger| 2.5 V P-P
Sync Output
Type| 2 x 3.5 mm TS jacks, DC-coupled
Impedance| 1 kO, unbalanced
Maximum output level| 10 V P-P
Control Inputs
Type| 6 x 3.5 mm TS jacks,summed
Impedance| 50 kΩ, unbalanced
CV range| ±10 V, 1 V/oct
Controls
PW level| -∞ to unity gain
PW manual| 50% to min
Waveform| Triangle, sawtooth, pulse
Range| 32′, 16′, 8′, 4′, 2′
Pitch| ±1 octive
Weak/strong| Sync mode select
Mod level| -∞ to unity gain
Power
Power supply| Eurorack
Current draw| 90 mA (+12 V),
70 mA (-12 V)
Physical
Dimensions| 81 x 129 x 46 mm
(3.2 x 5.1 x 1.8″)
Rack units| 16 HP
Weight| 0.2 kg (0.44 lbs)
LEGAL DISCLAIMER
Music Tribe accepts no liability for any loss which may be suffered by any
person who relies either wholly on or in part upon any description,
photograph, or statement contained herein. Technical specifications,
appearances and other information are subject to change without notice. All
trademarks are the property of their respective owners. Midas, Klark Teknik,
Lab Gruppen, Lake, Tannoy, Turbosound, TC Electronic, TC Helicon, Behringer,
Bugera, Oberheim, Auratone, and Coolaudio are trademarks or registered
trademarks of Music Tribe Global Brands Ltd. © Music Tribe Global Brands Ltd.
2021
All rights reserved.
LIMITED WARRANTY
For the applicable warranty terms and conditions and additional information
regarding Music Tribe’s Limited Warranty, please see complete details online
at musictribe.com/warranty.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>