behringer 1027 Clocked Sequential Control User Guide
- June 6, 2024
- Behringer
Table of Contents
Quick Start Guide
CLOCKED SEQUENTIAL CONTROL MODULE 1027
Legendary 2500 Series 8-Position Step
Sequencer Module for Eurorack
Controls
- CH A / CH B / CH C SEQUENCER COLUMNS – Use the knobs to set the control voltage output for each step. Each column sends out control voltages via that channel’s respective CH A / CH B / CH C output jack.
- STEP LEDs – Each LED light to indicate its respective sequencer step is active.
- POSITION GATES – Each of these output jacks sends out a gate signal for its respective sequence step via cables with 3.5 mm TS connectors. These 8 gate output signals are also available via the 12-pin GATE OUT LINK CONNECTOR located on the module underside. This 12-pin connector can connect to and trigger other compatible modules, such as the MIX-SEQUENCER MODULE 1050, via a 12-pin ribbon connector.
- RATE – This knob controls the step speed at which the sequencer moves from step to step. The knob operates in two overall frequency ranges determined by the LOW/HIGH switch.
- LOW/HIGH – Use this sliding switch to set whether the RATE knob operates in a lower-frequency (LOW) or higher-frequency (HIGH) range.
- % PULSE WIDTH – Select between width settings for the rectangular waveform ranging from 5% to 95% duty cycle. The PULSE WIDTH control operates on the CLK OUT jack only, making this control very useful for triggering other modules such as envelope generators, and so on.
- INT/EXT – Use this switch to select between internal (INT) or external (EXT) pulse width control voltage. When EXT is selected, the % PULSE WIDTH control knob is disabled.
- ON /OFF – This button starts or stops the sequence with a manual button push.
- STEP – Press this button to manually progress to the next sequencer step.
- RESET – Press this button to manually restart the sequence at step 1.
- STEP – Use this jack to route external trigger signals for the STEP button into the module via cables with 3.5 mm TS connectors.
- RESET – Use this jack to route external trigger signals for the RESET button into the module via cables with 3.5 mm TS connectors.
- ON – Use this jack to route external trigger signals to enable the step counter into the module via cables with 3.5 mm TS connectors.
- OFF – Use this jack to route external trigger signals to disable the step counter into the module via cables with 3.5 mm TS connectors.
- RATE – Use this jack to route in external control voltage signals for the sequencer’s step speed (usually controlled by the RATE knob) via cables with 3.5 mm TS connectors.
- WIDTH – This jack allows control voltage and modulation signals for the rectangular waveform to be routed in via cables with 3.5 mm TS connectors.
- CH A – This jack sends out control voltage signals for the CH A sequencer column via cables with 3.5 mm TS connectors.
- CH B – This jack sends out control voltage signals for the CH B sequencer column via cables with 3.5 mm TS connectors.
- CH C – This jack sends out control voltage signals for the CH C sequencer column via cables with 3.5 mm TS connectors.
- CLK OUT – Use this jack to export the internally generated clock signal via cables with 3.5 mm TS connectors. The internal clock produces a gate pulse every time the sequencer steps, and the gate pulse’s width can be adjusted using the % PULSE WIDTH control or via the WIDTH control jack.
Power Connection
The CLOCKED SEQUENTIAL CONTROL MODULE 1027 module comes with the required power cable for connecting to a standard Eurorack power supply system. Follow these steps to connect power to the module. It is easier to make these connections before the module has been mounted into a rack case.
- Turn the power supply or rack case power off and disconnect the power cable.
- Insert the 16-pin connector on the power cable into the socket on the power supply or rack case. The connector has a tab that will align with the gap in the socket, so it cannot be inserted incorrectly. If the power supply does not have a keyed socket, be sure to orient pin 1 (-12 V) with the red stripe on the cable.
- Insert the 10-pin connector into the socket on the back of the module. The connector has a tab that will align with the socket for correct orientation.
- After both ends of the power cable have been securely attached, you may mount the module in a case and turn on the power supply.
Installation
The necessary screws are included with the module for mounting in a Eurorack
case. Connect the power cable before mounting. Depending on the rack case,
there may be a series of fixed holes spaced 2 HP apart along the length of the
case, or a track that allows individual threaded plates to slide along the
length of the case. The free-moving threaded plates allow precise positioning
of the module, but each plate should be positioned in approximate relation to
the mounting holes in your module before attaching the screws. Hold the module
against the Eurorack rails so that each of the mounting holes is aligned with
a threaded rail or threaded plate. Attach the screws partway to start, which
will allow small adjustments to the positioning while you get them all
aligned. After the final position has been established, tighten the screws
down.
Specifications
Inputs|
---|---
On / off|
Type| 2 x 3.5 mm TS jacks,
DC coupled
Impedance| 100 KΩ, unbalanced
Maximum input level| 10 V
Minimum switching| 2.5 V, trigger
threshold| 1 x 3.5 mm TS jack,
DC coupled
Rate| 100 KΩ, unbalanced
Type|
Impedance| 10 V, 1 V/oct.
Maximum input level|
Width| 1 x 3.5 mm TS jack,
DC coupled
Type| 100 KΩ, unbalanced
Impedance| 10 V
Maximum input level| 2 x 3.5 mm TS jacks,
DC coupled
Step / reset|
Type| 100 KΩ, unbalanced
Impedance| 10 V
Maximum input level| 2.5 V
Outputs
Ch A / B / C|
Type| 3 x 3.5 mm TS jacks,
DC coupled
Impedance| 1 KΩ, unbalanced
Maximum output level| 10 V
Clock out|
Type| 1 x 3.5 mm TS jacks,
DC coupled
Impedance| 1 KΩ, unbalanced
Maximum output level| 5 V
Position gates|
Type| 8 x 3.5 mm TS jacks, DC-coupled
Impedance| 1 KΩ, unbalanced
Maximum Output level| 5 V
Controls
Rate| 1 x rotary knob,
Low (0.3 Hz to 15 Hz)
High (10 Hz to 400 Hz)
% Pulse width| 1 x rotary knob, 5% to 95%
Low/high| 1 x sliding switch
Int / ext| 1 x sliding switch
On / off| 1 x button, LED-backlit
Sequencer voltage knobs| 24 x rotary knob, 0 V to 10 V
Step / reset| 2 x momentary switch
Power
Power supply| Eurorack
Current draw| 70 mA (+12 V),
30 mA (-12 V)
Physical
Dimensions| 43 x 162 x 129 mm
(1.7 x 6.4 x 5.1″)
Rack units| 32 HP
Weight| 0.37 kg (0.81 lbs)
LEGAL DISCLAIMER
Music Tribe accepts no liability for any loss which may be suffered by any person who relies either wholly on or in part upon any description, photograph, or statement contained herein. Technical specifications, appearances and other information are subject to change without notice. All trademarks are the property of their respective owners. Midas, Klark Teknik, Lab Gruppen, Lake, Tannoy, Turbosound, TC Electronic, TC Helicon, Behringer, Bugera, Auratone, and Coolaudio are trademarks or registered trademarks of Music Tribe Global Brands Ltd. © Music Tribe Global Brands Ltd. 2020 All rights reserved.
LIMITED WARRANTY
For the applicable warranty terms and conditions and additional information regarding Music Tribe’s Limited Warranty, please see complete details online at musictribe.com/warranty.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>