D-Link Full HD Wi-Fi Camera DCS-8302LH User Manual
- June 6, 2024
- D-Link
Table of Contents
D-Link Full HD Wi-Fi Camera DCS-8302LH User Manual
Manual Overview
D-Link reserves the right to revise this publication and to make changes in the content hereof without obligation to notify any person or organization of such revisions or changes. Information in this document may become obsolete as our services and websites develop and change. Please refer to the www.mydlink.com website for the most current information.
Manual Revisions
Trademarks
D-Link and the D-Link logo are trademarks or registered trademarks of D-Link
Corporation or its subsidiaries in the United States or other countries. All
other company or product names mentioned herein are trademarks or registered
trademarks of their respective companies.
Copyright © 2020 by D-Link Corporation, Inc.
All rights reserved. This publication may not be reproduced, in whole or in
part, without prior expressed written permission from D-Link Corporation, Inc.
Product Overview
Package Contents
If any of the above items are missing, please contact your reseller.
Note: Using a power supply with a different voltage rating than the one included with your product will cause damage and void the warranty for this product.
Introduction
Meet the DCS-8302LH, the Full HD Wi-Fi Camera that lets you keep a closer eye on what’s happening at home. Its stylish design blends well into any home, while its sheltered weather resistance lets you place it in covered areas outside the home. From front porches to back patios, it’s – Home Surveillance, Unconfined.
System Requirements
Hardware Overview
Front
Back
LED Behavior
Installation
Safety
Please read all of the safety and operating instructions before using the device:
- Do not open the device or attempt to repair it.
- Make sure that the microSD card slot cover is securely closed before placing the camera outside.
- Do not submerge the device in liquid or attempt to clean it with liquids or solvents. To clean the device, disconnect it from the power outlet and use a damp towel to gently wipe it down.
- Heating of the exterior may occur if the spotlight is activated for long periods of time. This may occur if the live-view is used continuously for an extended period of time. Heating will not cause damage, premature failure or safety issues.
Before You Begin
Plan the location of your camera:
-
Verify that your camera is electrically rated to operate with the power available in your location.
-
Connect the camera’s power adapter into an electrical outlet that is not controlled by a wall switch. This will help avoid
accidentally turning off power to the device. -
Be sure to plug the device into a properly grounded electrical outlet in order to help prevent electric shock.
-
Make sure that the device is securely mounted.
Wireless Installation Considerations
The DCS-8302LH Full HD Wi-Fi Camera lets you view video footage from virtually anywhere within the operating range of your wireless network. Keep in mind that the number, thickness and location of walls, ceilings, or other objects that the wireless signals must pass through may limit the range. Typical ranges vary depending on the types of materials and background RF (radio frequency) noise in your home or business. The key to maximizing wireless range is to follow these basic guidelines:
- Keep the number of walls and ceilings between the camera and wireless access point to a minimum – each wall or ceiling can reduce your camera’s range from 1 to 30 meters (3 to 90 feet). Position your devices so that the number of walls or ceilings is minimized.
- Be aware of the direct line between network devices. A wall that is 0.5 meters (1.5 feet) thick at a 45-degree angle appears to be almost 1 meter (3 feet) thick. At a 2-degree angle it looks over 14 meters (42 feet) thick! Position devices so that the signal will travel straight through a wall or ceiling (instead of at an angle) for better reception.
- Building materials make a difference. A solid metal door or aluminum studs may have a negative effect on range. Try to position access points, wireless routers, and cameras so that the signal passes through drywall or open doorways. Materials and objects such as glass, steel, metal, walls with insulation, water (fish tanks), mirrors, file cabinets, brick, and concrete will degrade your wireless signal.
- Keep your product at least 1 to 2 meters (3 to 6 feet) away from electrical devices or appliances that generate RF noise.
mydlink App Camera Setup
- Download the mydlink app from the App Store (iOS) or Google Play (Android) by scanning the QR code.
https://d1rvtd08ngd4ef.cloudfront.net/new+mydlink/getUAP03.html?ios=1311150377&aos=com.dlink.mydlinkunified
Note: Ensure that your device is wirelessly connected to the network that
the DCS-8302LH will be in.
-
Launch the mydlink app and create a new account or sign in to your existing account.
Note: If you are asked about allowing the app to access your location or to send notifications, select Allow. Make sure location services and Bluetooth are turned on in your phone’s settings.
-
After logging in, tap the Menu button in the top-left corner.
-
Select Add a Device.
Follow the onscreen instructions to complete the device setup.
Device Placement
Place the camera 6.5 to 8 feet (2 – 2.5 meters) from the ground. Person Detection works best when the subject is between 6.5 to 23 feet (2 – 7 meters) away from the camera.
For outdoor installations: This device is designed to be installed under eaves or similarly covered locations, and does not support inverted installation. Please ensure that the device is installed with the rubber plug pointed downwards towards the ground, and that it is not installed in an area where it will experience continuous water exposure.
Mounting the Camera (Pole Mount)
-
Place the mounting bracket against the pole where you want it to
be positioned. -
Wrap the cable ties around the pole and thread them through the holes on the mounting bracket. Face the rough side of the cable ties to the pole to avoid slippage.
-
Twist the camera clockwise onto the mounting bracket until it securely locks into place.
Mounting the Camera (Wall Mount)
-
Place the mounting bracket against the wall where you want the
device to be positioned. Use a pencil to make two marks where the holes are located.
-
Use a 6 mm drill bit to drill two 26 mm deep holes over the pencil
marks.
-
Hammer in the plastic wall anchors to support the screws.
-
Align the mounting bracket’s holes over the plastic anchors. Drive the screws into the anchors to secure the mounting bracket.
-
Twist the camera clockwise onto the mounting bracket until it securely locks into place.
For outdoor installations: This device does not support inverted installation. Please ensure that the device is installed with the rubber plug pointed downwards towards the ground, and that it is not installed in an area where it will experience continuous water exposure.
Using the mydlink App
Controlling Your Device
Note: Screenshots are representative only. The mydlink app is constantly being updated and so may appear different.
After setting up your DCS-8302LH Full HD Wi-Fi Camera with a mydlink account in the mydlink app, you will be able to remotely access your camera through the app. After signing into your mydlink account, you will see a screen similar to the one on the right.
To access the device control options, tap to watch the live view, then tap again to access the control page. The following controls are available:
Device Settings
- Tap .
- Tap Device Settings.
- Tap the device you want to access the settings for.
The device page contains several options for you to configure your camera.
Troubleshooting
What do I do if my device is not working properly?
Reset the device and reinstall it. To reset your device, use a paper clip to
press and hold the recessed Reset button until the LED turns solid red.
During installation, ensure that:
- your router is connected to the Internet and has Wi-Fi enabled
- your mobile device has Bluetooth enabled
- your mydlink device is in range of your Wi-Fi network
How can I use voice commands to control my device?
The device will work with both Amazon Alexa and the Google Assistant. For setup instructions on these services, visit the following websites:
Alexa: dlink.com/en/alexa
The Google Assistant: dlink.com/en/google-assistant
Why is my microSD card not working/not supported?
The microSD card must be formatted with the correct file system (FAT32) before
it can be used with this product. This can be done in the mydlink app by
selecting the Format function in the storage menu under the Device Settings.
What is my username and password for setting up my device with an ONVIF system?
To connect your device to an ONVIF system, enter “admin” as the username and use the PIN code of your mydlink device as the password. You can find the PIN code on your device’s label.
Technical Specifications
Regulatory Information
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one of the
following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
– Consult the dealer or an experienced radio/TV technician for help.
Non-modifications Statement:
Any changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate this equipment.
Caution:
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
This device and its antenna(s) must not be co-located or operating in
conjunction with any other antenna or transmitter except in accordance with
FCC multi-transmitter product procedures. For product available in the
USA/Canada market, only channel 1~11 can be operated. Selection of other
channels is not possible.
Note
The country code selection is for non-USA models only and is not available to
all USA models. Per FCC regulations, all WiFi product marketed in the USA must
be fixed to USA operational channels only.
IMPORTANT NOTICE:
FCC Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
minimum distance 20 cm between the radiator and your body.
Innovation, Science and Economic Development Canada (ISED) Statement:
This Class B digital apparatus complies with Canadian ICES-003. Cet appareil
numérique de la classe B est conforme à la norme NMB-003 du Canada.
Innovation, Science and Economic Development Canada (ISED) Statement:
This device compliances with Industry Canada’s licence-exempt RSS standard(s).
Operation is subject to the following two conditions:
(1) this device may not cause interference, and
(2) this device must accept any interference, including interference that may
cause undesired operation of the device.
Radiation Exposure Statement
This equipment complies with ISED radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
minimum distance 20 cm between the radiator and your body.
The device meets the exemption from the routine evaluation limits in section
2.5 of RSS 102 and compliance with RSS-102 RF exposure, users can obtain
Canadian information on RF exposure and compliance.
European Community Declaration of Conformity:
Hereby, D-Link Corporation, declares that this product, accessories, and software are in compliance with directive 2014/53/EU. The full text of the EU Declaration of Conformity and product firmware are available for download from the product page at www.dlink.com
Warning Statement:
The power outlet should be near the device and easily accessible.
NOTICE OF WIRELESS RADIO LAN USAGE IN THE EUROPEAN COMMUNITY (FOR WIRELESS PRODUCT ONLY):
- This device is restricted to indoor use when operated in the European Community using channels in the 5.15-5.35 GHz band to reduce the potential for interference.
- This device is a 2.4 GHz wideband transmission system (transceiver), intended for use in all EU member states and EFTA countries. This equipment may be operated in AL, AD, BE, BG, DK, DE, FI, FR, GR, GW, IS, IT, HR, LI, LU, MT, MK, MD, MC, NL, NO, AT, PL, PT, RO, SM, SE, RS, SK, ES, CI, HU, and CY.
Usage Notes:
- To remain in conformance with European National spectrum usage regulations, frequency and channel limitations will be applied on the products according to the country where the equipment will be deployed.
- This device is restricted from functioning in Ad-hoc mode while operating in 5 GHz. Ad-hoc mode is direct peer-to-peer communication between two client devices without an Access Point.
- Access points will support DFS (Dynamic Frequency Selection) and TPC (Transmit Power Control) functionality as required when operating in 5 GHz band within the EU.
- Please refer to the product manual or datasheet to check whether your product uses 2.4 GHz and/or 5 GHz wireless.
SAFETY INSTRUCTIONS
The following general safety guidelines are provided to help ensure your own
personal safety and protect your product from potential damage. Remember to
consult the product user instructions for more details.
- Static electricity can be harmful to electronic components. Discharge static electricity from your body (i.e. touching grounded bare metal) before touching the product.
- Do not attempt to service the product and never disassemble the product. For some products with a user replaceable battery, please read and follow the instructions in the user manual.
- Do not spill food or liquid on your product and never push any objects into the openings of your product.
- Do not use this product near water, areas with high humidity, or condensation unless the product is specifically rated for outdoor application.
- Keep the product away from radiators and other heat sources.
- Always unplug the product from mains power before cleaning and use a dry lint free cloth only.
Disposing of and Recycling Your Product
This symbol on the product or packaging means that according to local laws and regulations this product should be not be disposed of in household waste but sent for recycling. Please take it to a collection point designated by your local authorities once it has reached the end of its life, some will accept products for free. By recycling the product and its packaging in this manner you help to conserve the environment and protect human health.
D-Link and the Environment
At D-Link, we understand and are committed to reducing any impact our operations and products may have on the environment. To minimize this impact D-Link designs and builds its products to be as environmentally friendly as possible, by using recyclable, low toxic materials in both products and packaging.
D-Link recommends that you always switch off or unplug your D-Link products when they are not in use. By doing so you will help to save energy and reduce CO2 emissions.
To learn more about our environmentally responsible products and packaging please visit www.dlinkgreen.com.
References
- Smart Home, SMB and Enterprise solutions | D-Link
- Amazon Alexa | D-Link
- Google Assistant | D-Link
- mydlink
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>