TRAILFX DHS001B Drop Down Step Bars Installation Guide
- June 6, 2024
- TRAILFX
Table of Contents
TrailFX Drop Down Step
Part No. DHS001B / DHS002B
Fits: 2015-2019 Chevrolet, GMC / Colorado / Canyon Crew
Cab & Ext Cab
Product image
| TO AVOID BEING SCRATCHED, PLEASE PROTECT THE SURFACE OF
THE TAILGATE VENT WAS COVERED CAREFULLY.
---|---
| REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE PRESENT.
| READ INSTRUCTIONS CAREFULLY BEFORE STARTING INSTALLATION.
| ALIGN THE STEP BARS AS DESIRED AND TIGHTEN ALL M10 FASTENERS TO 30 ft. –
lbs., AND THEM8 FASTENERS TO 15 ft.-lbs.
support@trailfx.com
1 866 638 4870
POLISHED STAINLESS STEEL – LIMITED LIFETIME POWDER-COATED BLACK – 3 YEARS
PARTS LIST:
Item| Qty| Part Description| Tools Needed
1| I| Step Bar Driver Side| 13 MM SOCKET & WRENCH
2| I| Step Bar Passenger Side| 14 MM SOCKET & WRENCH
3| 3| Mounting Bracket Driver Side| 15 MM SOCKET & WRENCH
4| 3| Mounting Bracket Passenger Side| RATCHET
5| 12| M8 Bolt| TORQUE WRENCH
6| 12| M8 Lock Washer|
7| 12| M8 Flat Washer|
8| 12| M 10 Flange Bolt|
9| 12| M 10 Flange Nut|
10| 12| M8 Nut Clip|
Mounting Kit Images
INSTALLATION PROCEDURE
- Remove plastic plugs from the rocker panel.
- Start at the front driver side of the vehicle and grab (2) M8 Nut clips (2) M8 hex head bolts, (2) M8 flat washer, and (2) M8 lock washer to driver mount bracket to the rocker panel. Assemble loosely. See Figures 1 and 2.
- Repeat for the center and rear locations.
- Repeat for the passenger side.
- Grab Driver Side Bar and install loosely to mount brackets with (6) M10 Flange bolts and (6) Serrated Flange Nuts. See Figure 3.
- Repeat for the passenger side.
- Align and adjust the step bars as needed and fully tighten all hardware.
- See Figure 4 for reference.
COMPLETE INSTALLATION
PRODUCT CARE
- Periodically check the product to ensure all fasteners are tight and components are intact.
- Mild soap may be used to clean the product.
FAQ’s
-
Mounting brackets are not getting Installed properly.
In some cases Illustration images shown in the Installation manual may not be the exactly same as actual vehicle images, also if Driver / Passenger side mounting brackets are very identical in the design, suggest referring Parts Identification guide to avoiding fitment issue. -
Products are thumping/rattling after installation.
Please ensure that all required mounting brackets/hardware are installed & tightened correctly. Suggest using white lithium / regular grease between the metal to metal contact surfaces. -
Missing / Excess Hardware.
Recheck hardware count as per the part list. -
Product not installed properly.
Ensure make model year, cab length, and bed size of your vehicle is listed in the application. All installation steps are followed correctly.
Check out these other TrailFX Products!!
Keystone Automotive Operations Inc. (KAO) warrants this product to be free of
defects in material and workmanship at the time of purchase by the original
retail consumer. KAO disclaims any other warranties, expresso implied,
including the warranty of fitness for a particular purpose or intended use. If
the product s found to be defective, KAO may replace or repair the product at
our option, when the product is returned prepaid, with proof of purchase.
Alteration to, improper installation or misuse of this product voids the
warranty. KAO’s liability is limited to repair or replacement of products
found to be defective and specifically excludes liability for any incidental
or consequential loss or damage.
www.TrailFX.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>