V-TAC Robot Vacuum VT-5522 Instructions

V-TAC Robot Vacuum VT-5522

Safety Precautions

General Safety Regulations

WARNING : Do not touch the robot’s electronics, battery or charging base. Users are not allowed to maintain internal components of the product.

• Product maintenance requires authorized professional maintenance personnel to operate. Please make sure that the nominal voltage of the power supply of the charging base is in accordance with the standard socket voltage.
• This device can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of this device in a safe way and understand the hazards involved.
• Children should be supervised to ensure they do not play with this device.
• Cleaning and maintenance shall not be performed by children without adult supervision.

Safety Instruction

• Please read all safety precautions and instructions before operating this robot.
• Please pay attention to all warnings on battery, power adapter, robot and instruction manual.
• Please follow all instructions described in this manual.
• The harm and the degree of damage caused by the wrong operation are explained as follows.
  Note : The company reserves the right to make any technical or design changes to the product as a result of continuous improvement. The right of interpretation belongs to the company.

Child Safety

• Children are not allowed to use this product alone.
• Children are not allowed to play with the packaging of the product, otherwise, it may cause suffocation.

Notice

1. This product can only use the battery provided by the manufacturer.
2. The battery must be taken out when the product is discarded.
3. If you need to replace the battery, please contact our after-sales service department. If you use the wrong type of battery to replace it, it may cause a safety accident.
4. In case of battery leakage, and if you accidentally let the liquid contact with the skin or clothing, you should immediately wipe with a dry cloth. Waste batteries should be sent to the recycle center or designated maintenance center, which cannot be thrown away.

INTRODUCTION
Thank you for selecting and buying V-TAC product. V-TAC will serve you the best. Please read these instructions carefully before starting the installation and keep this manual handy for future reference. If you have any another query please contact our dealer or local vendor from whom you have purchased the product. They are trained and ready to serve you at the best.

WARNING

• This product can only use the original battery charging base and adapter, otherwise it may cause damage, electric shock or fire caused by high voltage.
• If the robot and accessories are found damaged, please stop using the product immediately. Please contact our after-sales service department. Except for the professional maintenance personnel designated or authorized by the company, no one is allowed to disassemble, repair or modify the product.
• Do not touch the power plug or product with wet hands to avoid possible electric shock.
• Do not use this product in the suspended environment without protective guard, so as to avoid the vacuum cleaner falling accidentally and causing personal injury.
• Do not drag or move the product through the power cord. Do not unduly twist, bend or place heavy objects on the power cord.
• Do not let the product near the source of fire or close to flammable, explosive and corrosive materials.
• Do not let clothing or any part of your body (such as hair, fingers, etc.) be sucked into the brush or wheels of the vacuum cleaner as this can cause personal injury.

ATTENTION

• This product is for indoor use only.
• Avoid vacuum cleaner damage caused by inhalation of water, oil or other liquids.
• Before use, please tidy up the scattered wires on the ground, so as not to interfere with the work of the vacuum cleaner.
• Do not place heavy weight on the vacuum cleaner.
• Do not lift the vacuum cleaner by the front shell alone, as it will damage the vacuum cleaner
• The charging stand should be placed against the wall. The adapter cord should not be placed randomly on the floor to prevent it from being wound around the bottom of the vacuum cleaner.

Package Contents

Product Composition / Part Name

• Removing the dust box: Hold the handle and pull it out as shown in the image on the left.
• Installing the dust box: Fix the dust box into the vacuum. Ensure it is installed correctly.
• Clean the side brush with the cleaning brush. If there is lot of hair on the side brush, you can use scissors to carefully cut the hair, and then clean.

1. Installation steps: Align the side brush with the hole at the bottom and press down until you hear a “click” to indicate that the side brush is in place.
2. Disassembly steps: Grab the bristles on both ends of the side brush and pull them out gently.
   Tips :
   Before each use, please check whether these side brushes have been assembled, otherwise it will affect the normal cleaning work of the vacuum cleaner.

Usage

Attention : Before cleaning, it is necessary to remove the protective block at the front shell of the machine, and tidy up small objects or obstacles in the room, especially wire entanglements, to prevent them from getting stuck and winding into the bottom of the machine.

The product is suitable for the following floor environment:

Range of non-application

• This product is for indoor use only.
• Do not use this product in the suspended environment without protective guard, so as to avoid the vacuum cleaner falling accidentally and causing personal injury.
• Do not use this product in wet or flammable, explosive, or corrosive environments.
• Do not allow this product to absorb unextinguished cigarette butts or matches.
• This product cannot be used to absorb the toner used in laser printer or copier. These substances may cause fire disaster.
• Do not use this product to absorb sharp objects, such as glass, nails, etc., to avoid product damage.

Operating Status of Robot

1. OFF status
   When the vacuum cleaner is off, long press the “ “ button, and the blue light will be on after the buzzer goes off. The vacuum cleaner will enter the standby mode after 3 seconds.

2. Standby status
   1. If there is no operation, the vacuum cleaner will automatically shut down after 5 minutes of standby.
   2. Press the ” ” button once, the buzzer will ring, turn the machine on and off.

3. Remote control status

4. Press ” ” to adjust the suction of the machine fan.

5. Press the edge cleaning button of ” ” to enter the edge cleaning mode.

6. Press the fixed point cleaning key of ” ” to start the area cleaning with the current point as the circle.

Indicator light function prompt

Automatic cleaning
Automatic cleaning mode is suitable for cleaning the whole home environment. In the automatic cleaning state, the blue light of the machine shines.

1. After the machine starts, firstly it scans and identifies the environment, establishes the cleaning area and plans the cleaning path;
2. Then, according to the planning area, uses the arched path for cleaning, and automatically avoid obstacles and steps, etc.
3. Set up the cleaning path map in real time to complete the planned path cleaning and ensure that all areas can be cleaned.

Charging mode
In charging mode, the blue and purple lights flicker alternately to indicate that the robot is in charging mode. Once the robot has been fully charged it will indicate with a constant purple light. Fault detected mode

Failure alarm function of indicator light and solution

Charging

Manual charging
Connect the power adapter jack directly to the robot and then plug the charging cable into the power supply.

1. Please completely charge the robot for 12 hours when charging for the first time.
2. For daily use, please place the robot on the charging base and ensure that the charging base is connected to the power supply.
3. If you do not use the vacuum cleaner for a long time, please fully charge it and then turn if off to store it in a ventilated and dry place.

Maintenance

Clean the side brush
Please clean the side brush when it becomes dirty. If the side brush is damaged, it can be replaced.
Clean the dust box and filter
After each use, please clean the dust box and filter in time. Specific operations are shown in the following figure:

Tips : After taking out the dust box, please check whether there is any foreign object in the suction inlet and clean it.

References

• tac.eu

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>