Stander EZ Adjust Bed Rail User Guide

June 6, 2024
Stander

Assembly & Installation Instructions:

Specifications:

  • Maximum User Weight: 300lbs
  • Mattress Thickness range: 12 inches to 16 inches.
  • Cleaning: Clean product with warm water and soap. Dry thoroughly before using.
  •  Recycling: Product should be recycled in accordance with national guidelines.

Entrapment Warnings:

Also, refer to the Entrapment Prevention Guidelines sheet provided with these instructions.

  • Product Position: Keep the product at least 12.5 inches from the head and foot end plane of the bed to help prevent entrapment issues as shown in the images below.
  • Safety Strap: It is important that the Bedrail is secured to the Side of the mattress. The Safety Strap is looped around the Bed Frame on the opposite side of the bed, buckled, and tightened as shown in the images below.

Stander EZ Adjust Bed Rail -

Instructions:

  1. Remove all components from the box and verify all parts are included as shown in Figure 1.
    Stander EZ Adjust Bed Rail - FIGURE 1

  2. Use the Allen Head Wrench to attach the CONNECTION TUBE to the BASE TUBES using the SHORT BOLTS and WASHERS as shown in Figure 2. NOTE: Nuts are welded on inside of CONNECTION TUBE.
    Stander EZ Adjust Bed Rail - FIGURE 2

  3. Determine which side of the bed to install the Bed Rail. Slide the assembled base structure from Figure 2, between the mattress and box spring of the bed as shown in Figure 3.
    Stander EZ Adjust Bed Rail - Determine which

  4. NOTE: There are two different directions in the bedrail that can be installed. The EXTENSION SIDE OF THE BED RAIL must be closest to the FOOT OF THE BED as shown in Figure 4.
    Stander EZ Adjust Bed Rail - different directions

  5. Secure the HANDLE ASSEMBLY to the BASE STRUCTURE with LONG BOLTS, WASHERS, and NUTS as shown in Figure 5.
    NOTE: Bed not shown for visual clarity.
    Stander EZ Adjust Bed Rail - HANDLE ASSEMBLY

  6. IMPORTANT!!! Secure the SAFETY STRAP to the bed frame, as shown in Figure 6. Unbuckle strap and loop strap around the bed frame and re-buckle. Tighten the strap to secure Handle Assembly against the side of the mattress. DO NOT INSTALL THE PRODUCT WITHOUT SECURING THE SAFETY STRAP TO THE BED FRAME AS SHOWN IN FIGURE 6. IF YOU HAVE ANY QUESTIONS CALL STANDER AT 800-506-9901 or 435-755-0453.
    Stander EZ Adjust Bed Rail - MPORTANT

  7. To extend the bed rail, depress the button on top of the bed rail and pull the extension side of the bed rail outward. To lower bed rail, pull and rotate Knobs 90 degrees until Index Pin engages the Short Slot, as shown below in Figure 7.
    Stander EZ Adjust Bed Rail - FIGURE 7

ATTENTION
There is a potential risk of serious injury or death associated with virtually every product regardless of its type or intended use.
Stander, Inc., has worked tirelessly to minimize all risks associated with its mobility aids, yet given the types of products, users, and a myriad of things outside of our control, we cannot eliminate every conceivable risk. Accordingly, a consumer must use common sense when utilizing our products and consider the user’s overall physical and mental health.
Read all the materials that accompany this product before it is installed or used.

This product is intended to assist disabled persons to provide minimal to moderate weight support while standing from the bed. This product is not intended to be used as a device to restrain individuals from getting into and out of bed.

LIMITED WARRANTY

Stander, Inc. warrants to the original purchaser that this product will be free from defects in material and/or workmanship for 2 years from the date of purchase. During the warranty period, we will correct any defects in material or workmanship at no charge. All shipping cost must be paid by the original purchaser. Any replacement parts will be new and are warranted for the remainder of the original warranty or thirty (30) days from the date of shipment, whichever is longer. The original purchaser must notify Stander, Inc. during the warranty period in writing of the defect in workmanship or material. This warranty is not transferable and covers only normal use. Stander will not refund or pay for any shipping charges. The warranty does NOT cover: (1) Damage during shipment other than original shipment to the retailer; (2) Damage caused by unauthorized attachments, alterations, or modifications; (3) Damage caused by the use of the product for purposes other than those for which the product was designed or intended; and (4) Damage caused by any other abuse, misuse, mishandling or misapplication.

Under no circumstances shall Stander, Inc. be liable for any special, incidental, or consequential damages based upon breach of this limited
warranty, breach of contract, or strict liability.

THERE ARE NO WARRANTIES THAT EXTEND BEYOND THOSE INDICATED HEREIN. ALL OTHER WARRANTIES, EXPRESS OR IMPLIED (INCLUDING ALL IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE), ARE HEREBY DISCLAIMED.

Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you. This warranty gives you specific legal right, and you may also have other rights which vary from state to state. To obtain service under this warranty, you
can reach Stander, Inc. at 800-506-9901 or 435-755-0453.

WARNINGS

  1. INSTALLATION:
    a) Do not use or install this product unless you read and understand these warnings and assembly instructions to ensure the product
    is properly installed and used. If installer/user(s) are installing this product in a nursing home, assisted living center, or a similar facility, follow these instructions and the facilities Bed Rail/Handle installation policies. If this product does not comply with the facility’s installation policies, do not install this product. This product must be installed per “Entrapment Prevention Guidelines” the sheet included with this product. If you have any questions regarding the installation, use, associated risks, or anything at all regarding this product call Stander Inc. at 800-506-9901 or (435) 7550453.
    b) Improper installation of this product significantly increases the risk of entrapment (see the section on ENTRAPMENT below). Do NOT install the product without a bed frame under any circumstances. Do not install this product if you are unable to follow the instruction exactly.
    c) This product should only be used with innerspring or memory foam style mattresses. IMPORTANT: Read the instructions below to make sure your mattress thickness is appropriate to use this product. This product should not be used on any bed which consists of a material that may increase the potential for gapping between the top of the mattress and the bottom of the Bed Handle.
    Examples of beds that will cause gapping problems to include, but are not limited to waterbeds, lightweight foam, air, or other lightweight mattresses.
    d) Prior to using, ensure that there is no gap between the side of the product and the side of the existing bed mattress. A gap in this area means the product was installed improperly. The included components (such as clamps, safety straps, or other means) are designed to secure the product to the existing bed frame to avoid a gap in this area.
    e) This product is equipped with components to secure the product to a bed (such as clamps, safety straps, or other means). These components are intended to reduce the risk of entrapment (see the section on ENTRAPMENT below). NEVER remove these components (such as clamps, safety straps, etc.) or use products without these components installed as per Assembly Instructions. Removal, modification, or alteration of these components significantly increases the risk of entrapment.
    f) In the rare possibility of an adverse event with a Stander product, contact a customer service representative at 800-506-9901 or 435-755-0453 immediately. Also, report to the competent authority of your member state.
    g) A serious event is defined as death or serious deterioration in health that results in a life-threatening illness or injury, permanent impairment, hospitalization, or surgical intervention.
    h) Stop using immediately if the product is damaged, or broken, or if parts are missing.
    i) Stop using immediately if the product shifts out of its original position until it is readjusted into the correct position.
    j) In addition to contacting the manufacturer directly, consumers should report problems to the CPSC at this website:
    SaferProducts.gov or call 1-800-638-2772, or to the FDA at 1-800-332-1088.
    k) For further information, see: cpsc.gov/en/Safety-Education/Neighborhood- Safety-Network/Posters/Adult-Bed-Rails/ and
    www.fda.gov/bedsafety

  2. ENTRAPMENT:
    a) There is a risk of entrapment associated with bed rails and other similar bedside mobility aids. Entrapment occurs when an individual becomes wedged between a bed rail and any other object. Entrapment has resulted in serious injury and death. Read the enclosed Entrapment Prevention Guidelines before installation or use of this product. Additional copies of the Entrapment Prevention Guidelines may be obtained from www.stander.com or by contacting a Stander representative at 800-506-9901 or 435-755-0453.

  3. PHYSICAL AND MENTAL CONDITIONS:
    a) Individuals who have problems with physical limitations, paralysis, symptoms of dementia, Alzheimer’s or memory loss, sleeping, incontinence, pain, uncontrolled body movement, getting out of bed and walking unsafely without assistance, frailty, weakness, confusion, restlessness, terminal restlessness, or are under the influence of medications, drugs, or any substance that could impair their balance or judgment, or any other unforeseeable reasons that could affect the users physical and mental ability to safely use this product, are at a higher risk of entrapment. Since these conditions are subjective and Stander Inc. has no control over who chooses to use this product, it is the installer/user(s) responsibility to consult a physician before using this product.
    b) This product is not intended to carry the full weight of an individual. This product is only intended to provide balance and support
    while sitting and standing.

  4. EXTERNAL FACTORS:
    a) Children should not be allowed to hang on or play with this product.
    b) Changing bed linens (bed covers, blankets, sheets, etc.) may require re- tightening of the clamp(s) to eliminate a gap between the Bed Handle and side of the mattress.
    c) If the product is removed and reinstalled, clamp(s) needs to be reinstalled correctly as directed in these instructions.

  5. AGREEMENT BETWEEN INSTALLER/USER(S) AND STANDER INC.:
    a) If the installer/user(s) choose to use this product, it is understood between the installer/user(s) AND Stander Inc., that the installer/user(s) accept
    the risks associated with using this product. Since these conditions are subjective and Stander Inc. has no control over who chooses to use this product, the installer/user(s) agree to be liable for their decisions when using this product.

  6. CONSUMER RIGHTS AND ARBITRATION AGREEMENT:
    a) This arbitration agreement (“Agreement”) affects your legal rights and remedies by providing that disputes between you and the manufacture of this product (“Stander”), must be resolved through binding arbitration, rather than in a court. Please read this agreement carefully as you accept the terms of this agreement by assembling and using this product. If you do not agree to the terms of this agreement, return the product to the location of purchase for a refund.
    i) RESOLUTION OF CLAIMS OR DISPUTES. Any claim or dispute between you and Stander arising out of or relating in any way to the Product or this Agreement shall be resolved through final, binding arbitration. This arbitration obligation applies regardless of whether the claim or dispute involves a tort, fraud, misrepresentation, product liability, negligence, violation of a statute, or any other legal theory. Both you and Stander specifically acknowledge and agree that you waive your right to bring a lawsuit based on such claims or disputes and to have such a lawsuit resolved by a judge or jury. ii) LIMITATION OF LEGAL REMEDIES. All arbitrations under this Agreement shall be conducted only on an individual (and not a class-wide) basis and an arbitrator shall have no authority to award class-wide relief. You acknowledge and agree that this Agreement specifically prohibits you from commencing arbitration proceedings as a representative of others or joining in any arbitration proceedings brought by any other person. iii) ARBITRATION PROCEDURES.
    (1) Before commencing any arbitration proceedings under this Agreement, you must first present the claim/dispute to Stander by calling 800-506-9901 or 435-755-0453, providing requested contact information and allowing Stander the opportunity to resolve it. If your claim or dispute is not resolved within sixty (60) days, you may commence arbitration proceedings in accordance with the terms of this Agreement.
    (2) The arbitration of claim(s)/dispute(s) under this Agreement shall be pursuant to the American Arbitration Association’s (“AAA”) United States Commercial Dispute Resolution Procedures and Supplementary Procedures for Consumer-Related Disputes (see www.adr.org for their rules and procedures).
    (3) The arbitration of any claim/dispute under this Agreement shall be in the State of Utah.
    (4) All administrative expenses of arbitration proceedings under this Agreement shall be divided equally between you and the Company, except that: (a) if the claims/dispute subject to the arbitration proceedings is less than ten thousand dollars (US$10,000), you will be responsible for no more than one hundred twenty-five dollars (US$125) in administrative expenses; (b) if the claim/dispute subject to the arbitration proceedings is more than ten thousand dollars (US$10,000) but less than seventy-five thousand dollars (US$75,000), then you will be responsible for no more than three hundred seventy-five dollars (US$375) in administrative expenses; and (c) if the claim/dispute subject to the arbitration proceedings is more than seventy-five thousand dollars (US$75,000), then you will be responsible for administrative expenses in accordance with the Commercial Fee Schedule provided by the AAA. You acknowledge and agree that each party shall pay the fees and costs of its own counsel, experts, and witnesses. iv) CHOICE OF LAW & SEVERABILITY. This Agreement shall be governed by the United States Federal Arbitration Act and the laws of the state of Utah. If any provision of this Agreement is declared or found to be unlawful, unenforceable, or void, such provision will be ineffective only to the extent that it is found unlawful, unenforceable, or void and the remainder shall remain fully enforceable.

WARNING ENTRAPMENT, STRANGULATION, SUFFOCATION, AND FALL HAZARD

Gaps in and around this product can entrap and kill. People with Alzheimer’s disease or dementia, or those who are sedated, confused, or frail, are at increased risk of entrapment and strangulation. People attempting to climb over this product are at increased risk of injury or death from falls. Always make sure this product is properly secured to the bed. If a product can move away from the bed or mattress, it can lead to entrapment and death.

WARNING SUFFOCATION /STRANGULATION /ENTRAPMENT HAZARD

If the product is installed incorrectly or moves from its initial position gaps can occur which can entrap and kill. People with Alzheimer’s disease, dementia, or other neurological conditions, or those who are sedated, confused, or frail, are at increased risk of entrapment, suffocation and strangulation.

  • NEVER use unless the product is tight against the mattress, without gaps, and at least 12 ½″ from headboard and footboard.
  • NEVER use with children.
  • NEVER use on toddler, bunk, water, or inflatable beds or on beds with mattress toppers or soft compressible pads.

Stander EZ Adjust Bed Rail

Product Number: 8000 EZ Adjust Bed Rail, V3.3, January 14th, 2021

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals