BOGEN HS7EZ Easy Design Speaker Instruction Manual
- June 6, 2024
- BOGEN
Table of Contents
Easy Design™Speaker
Model HS7EZ
Speaker Layout
Figure 2
PLACEMENT
| A| B| C| Volume Setting
---|---|---|---|---
Low Noise (55dB-65dB)| 60 ft.| 120 ft.| 80 ft.| 1/2 Rotation
Medium Noise (65dB-75dB| 50 ft.| 100 ft.| 60 ft.| Full Clockwise
The layout of the speakers should be planned prior to installation. Desired
mounting height, barring obstructions, is 15 to 20 feet, with the speakers
angled downward toward the listening area and facing in the same direction.
The layout starts in one corner of the area. The first speaker in Row 1 should
be positioned a distance equivalent to (A) (see Figure 2) from the corner
based on the noise level of the area. The next speaker in Row 1 should be a
distance equivalent to (B) (see Figure 2) from the first speaker. Each
additional speaker in the row should use this same spacing.
Row 2 starts a distance equivalent to (C) (see Figure 2) from Row 1 and, like
Row 1, each speaker should be a distance apart equivalent to (B).
Row 3 starts a distance equivalent to (C) from Row 2. Continue this pattern of
alternating rows until the area is appropriately covered.
For areas that include high shelving or corridors, speakers should be
installed so that they project down the aisles between the shelves or down
through the corridors.
The spacing of the speakers can be adjusted so that the speakers are evenly
spaced in a row.
NOTE: Each environment is unique. This layout plan is general in nature
and may not be applicable for every installation.
Speaker Installation
STEP 1 – For easier installation, remove the flange (base) from the speaker by unscrewing the wing nut. Place the flange flush with the mounting surface and mark the pivot area using either a marker or chisel. Drill the appropriately sized hole and screw the flange to the surface. Place another screw in the front of the flange for swivel control purposes (see Figure 3). (Use appropriate hardware for your specific mounting surface.)
STEP 2 – After mounting the flange, reattach the speaker to the flange
and aim the speaker for the desired coverage. A 45-degree downward angle is
recommended, but this may vary depending upon speaker layout.
STEP 3 – Make the electrical connection using the two wires connected to
the speaker. The suggested amplifier connections are:
| Amplifier Outputs | Speaker Connections |
|---|---|
| 70V Red | 70V Red |
| COM | Wire |
NOTE: The speaker will also work perfectly well with these connections
reversed. However, it is important to be consistent in the wiring of the
speakers in the system.
STEP 4 – Adjust the volume control located on the horn to the desired
setting. See Figure 2 for the suggested initial settings based on the ambient
noise level of the environment.
Limited Warranty; Exclusion of Certain Damages
The HS7EZ is warranted to be free from defects in material or workmanship from
the date of sale to the original purchaser for the lifetime of the product.
Any part of the product covered by this warranty that, with normal
installation and use, becomes defective will be repaired or replaced by
Bogen, at our option, provided the product is shipped insured and prepaid to:
Bogen Factory Service Department, 50 Spring Street, Ramsey, NJ 07446, USA.
The product will be returned to you freight prepaid. This warranty does not
extend to any of our products that have been subjected to abuse, misuse,
improper storage, neglect, accident, improper installation or have been
modified or repaired or altered in any manner whatsoever, or where the serial
number or date code has been removed or defaced.
THE FOREGOING LIMITED WARRANTY IS BOGEN’S SOLE AND EXCLUSIVE WARRANTY AND
THE PURCHASER’S SOLE AND EXCLUSIVE REMEDY. BOGEN MAKES NO OTHER WARRANTIES OF
ANY KIND, EITHER EXPRESS OR IMPLIED, AND ALL IMPLIED WARRANTIES OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE ARE HEREBY DISCLAIMED AND
EXCLUDED TO THE MAXIMUM EXTENT ALLOWABLE BY LAW. Bogen’s liability arising
out of the manufacture, sale or supplying of products or their use or
disposition, whether based upon warranty, contract, tort or otherwise, shall
be limited to the price of the product. IN NO EVENT SHALL BOGEN BE LIABLE FOR
SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO,
LOSS OF PROFITS, LOSS OF DATA OR LOSS OF USE DAMAGES) ARISING OUT OF THE
MANUFACTURE, SALE, OR SUPPLYING OF PRODUCTS, EVEN IF BOGEN HAS BEEN ADVISED
OF THE POSSIBILITY OF SUCH DAMAGES OR LOSSES. Some states do not allow the
exclusion or limitation of incidental or consequential damages, so the above
limitation or exclusion may not apply to you. This warranty gives you specific
legal rights, and you may also have other rights which vary from State to
State.
Products that are out of warranty will also be repaired by the Bogen Factory
Service Department — same address as above or call
201-934-8500. The parts and labor
involved in these repairs are warranted for 90 days when repaired by the Bogen
Factory Service Department. All shipping charges in addition to parts and
labor charges will be at the owner’s expense. All returns require a Return
Authorization number.
Specifications are subject to change without notice.
© 1999 Bogen Communications Inc. All rights reserved.
Part No. 54-5071-01B 0809
COMMUNICATIONS, INC.
www.bogen.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>