VANCE HINES 14339 2021 Plus Honda Grom Hi Output Hooligan PCX Instruction Manual

VANCE HINES 14339 2021 Plus Honda Grom Hi Output Hooligan PCX

Product Information

Specifications

• Product Name: Vance & Hines Hi-Output Hooligan PCX
• Part Number: 14339
• Weight: 5.614 lbs.

Parts List

FAQ

• Q: Where can I find technical support for this product?
  • A: You can contact our technical support line at 562-921-7461 for any assistance you may need.

Product Installation Instructions

Stock System Removal

1. Remove the two-cylinder exhaust port nuts from the head pipe, located at the cylinder head.
2. Remove the exhaust chassis mount bolt.
3. Remove the muffler mount bolt.
4. Remove the complete exhaust system and set it aside (assistance may be required).
5. Remove the rubber grommet from the stock muffler mount.
6. Check the condition of exhaust gaskets and replace if worn or damaged.

Vance & Hines System Installation

1. Install the header using the supplied M8 nuts (A170HW). Do not fully tighten at this time.
2. Slip the midpipe (H674RB) onto the header (H173FB). Align the spring clips.
3. Attach the bracket (1276) to the muffler (H675RB-S) with the two M6 screws (A544HW). Fully tighten the bracket to the muffler. Be sure to align the mounting bracket with the muffler tent bracket.
4. Slip the muffler (H675RB-S) onto the midpipe (H674RB).
5. Attach the muffler with the bracket (1276) to the muffler mount (Figure 1).

Congratulations, you have purchsed the finest exhaust system available for your motorcycle. Your Vance & Hines exhaust is designed and crafted for performance, quality, and style. Please follow the instructions below, check exhaust system for missing or damaged parts and if you need any assistance please contact our technical support line 562-921-7461.

PARTS LIST

HARDWARE

TOOLS REQUIRED

• Wrenches: 12mm, 13 mm
• Allen Wrench: 4mm, 6mm
• Sockets: 12mm

INSTALLATION  INSTRUCTIONS

STOCK SYSTEM REMOVAL

1. Remove the two cylinder exhaust port nuts from head pipe, located at the cylinder head.
2. Remove the exhaust chassis mount bolt.
3. Remove the muffler mount bolt.
4. Remove the complete exhaust system and set aside (assistance may be required).
5. Remove the rubber grommet from stock muffler mount.
6. Check the condition of exhaust gaskets and replace if worn or damaged.

VANCE & HINES SYSTEM INSTALLATION

1. Install header using supplied M8 nuts (A170HW). Do not fully tighten at this time.
2. Slip midpipe (H674RB) onto header (H173FB). Align the spring clips.
3. Attach bracket (1276) to muffler (H675RB-S) with the two M6 screws (A544HW). Fully tighten bracket to muffler. Be sure to align mounting bracket with muffler tent bracket.
4. Slip muffler (H675RB-S) onto midpipe (H674RB).
5. Attach muffler with bracket (1276) to muffler mount (Figure 1).
   • Insert bracket spacers (A775ST) in-between the bracket and muffler mount.
   • Insert M8 socket head screw (A452HW) into M8 socket head cover (A713ST).
   • Install muffler assembly using washer (A616HW) and one M8 nut (A170HW).
   • Do not fully tighten at this time.
6. Tighten cylinder exhaust port nuts evenly.
7. Tighten muffler mounting screw.
8. Attach exhaust springs (A115SP) using supplied spring puller.

VANCE & HINES SYSTEM INSTALLATION

1. When installing new stainless steel make sure your hands are clean and free of oil. After installation, thoroughly clean pipes and mufflers with a soft cloth and cleaning solvent that will leave no residue (acetone, glass cleaner, alcohol,etc…) before starting the motorcycle.
2. It is considered normal for stainless steel exhaust systems to discolor due to heat.
3. High performance engine tuning utilizing a dyno will likely result in severe discoloration.
4. Avoid long periods of idling as this can cause discoloration. Intake leaks can cause the engine to run lean and overheat, this could lead to discoloration.

Emissions Notice

In California, in order to meet Air Resources Board emissions requirements, certain aftermarket part applications have been identified as replacements, and others have received ARB Executive Orders. All other emissions related aftermarket parts are for competition use only. A list of replacement parts and EO parts, and corresponding fitment is provided at vanceandhines.com/California.

Warranty

All Vance & Hines products are warranted against defects in material and workmanship for a period of 90 days. This warranty does not cover discoloration or rust. This warranty shall be limited to the repair or replacement of the product, which may be proven defective under normal use. Vance & Hines will not warranty any system that has been abused, misused, improperly installed or modified.

Dealers or distributors are not authorized to make dispositions binding upon Vance & Hines. Vance & Hines will not be responsible for any labor charges incurred in removing or replacing any system under warranty. A return authorization number and a copy of the original purchase invoice must accompany all returns. Parts returned without a return authorization may be refused.

CONTACT

• 13861 ROSECRANS AVENUE / SANTA FE SPRINGS, CA 90670
• SALES: 562-921-5388
• TECHNICAL: 562-926-5291
• FAX: 562-802-0110
• vanceandhines.com

References

• CALIFORNIA CUSTOMER - Vance & Hines
• Home Page - Vance & Hines

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>