audio-technica AE3300 Cardioid Condenser Handheld Microphone User Manual

: June 6, 2024
: Audio-Technica

Table of Contents

Features
Notes on use
Safety precaution
Connection procedure
Specifications
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

audio-technica AE3300 Cardioid Condenser Handheld Microphone User Manual

Thank you for purchasing this product. Before using the product, read through the user manual to ensure that you will use the product correctly. Please keep this manual for future reference.

Features

Exceptional performance for exceptional performers
Same element as the classic AT4033 studio microphone
Superior anti-shock engineering ensures low handling noise and quiet performance
Cardioid polar pattern reduces pickup of sounds from the sides and rear, improving isolation of desired sound source
Multi-stage grille design offers excellent protection against plosives and sibilance without compromising high-frequency clarity
Robust all-metal design for enduring dependability on the road
Integral 80 Hz HPF switch and 10 dB pad.

Notes on use

With pristine audio quality, ultra-low handling noise, and high-frequency clarity, AE3300 gives voice to the subtleties of vocal performance. This cardioid condenser vocal microphone features the condenser element used in the legendary AT4033 and proven in the world’s finest recording studios. The hardened-steel outer grille is lined with fine steel mesh and a layer of open- cell foam for ultimate protection against vocal plosives without compromising high-frequency clarity. Its superior anti-shock engineering ensures low handling noise and quiet performance. For exceptional performance. For exacting detail. For brilliant clarity: AE3300. it’s the new standard in live audio.

When using the AE3300 in settings with a stage monitor speaker, the speaker should be located 180° off axis (at rear of the microphone). This placement, in conjunction with the microphone’s uniform cardioid pickup pattern, will virtually eliminate the possibility of undesired audio feedback.

An integral 80 Hz hi-pass filter provides easy switching from a flat frequency response to a low-end roll-off. The roll-off position reduces the microphone’s sensitivity to popping in close vocal use. It also reduces the pickup of low- frequency ambient noise (such as traffic, air-handling systems, etc.), room reverberation and mechanically-coupled vibrations.

Avoid leaving the microphone in the open sun or in areas where temperatures exceed 43°C for extended periods. Extremely high humidity should also be avoided.

Safety precaution

Although this product was designed to be used safely, failing to use it correctly may result in an accident. To ensure safety, observe all warnings and cautions while using the product.

Cautions for the product

Do not subject the product to strong impact to avoid malfunction.
Do not disassemble, modify or attempt to repair the product.
Do not handle the product with wet hands to avoid electric shock or injury.
Do not store the product under direct sunlight, near heating devices or in a hot, humid or dusty place.

Connection procedure

Connect the output terminals of the microphone to a device that has a microphone input (balanced input) compatible with a phantom power supply. The output connector is an XLRM-type with polarity as shown in the figure below.

Terminal
This product requires 48 V DC phantom power.

Specifications

Element: Fixed-charge back plate, permanently polarized condenser
Polar pattern: Cardioid
Frequency response: 30 – 18,000 Hz
Low Frequency response: 80 Hz, 12 dB/octave
Open circuit sensitivity: -42 dB (7.9 mV) re 1V at 1 Pa
Impedance: 150 ohms
Maximum input sound level: 147 dB SPL, 1 kHz at 1% T.H.D.
157 dB SPL, with 10 dB pad (normal)
Noise: 19 dB SPL
Dynamic range (typical): 128 dB, 1 kHz at Max SPL
Signal-to-noise ratio: 75 dB, 1 kHz at 1 Pa
Phantom power requirements: 11-52 V DC, 3 mA typical
Switch: High-pass filter, 10 dB pad (normal)
Weight (less accessories): 300 g
Dimensions: 179.0 mm long, 50.0 mm head diameter, 33.0 mm to 22.0 mm tapered body diameter
Output connector: Integral 3-pin XLRM-type
Included accessories: AT8470 Quiet-Flex stand clamp for 5/8″-27 threaded stands; soft protective pouch.