EGLO 35016 ANTIBES Ceiling Fan Instruction Manual

EGLO 35016 ANTIBES Ceiling Fan

Intended use
This ceiling fan is solely suitable for use in dry, closed indoor spaces. It is not suitable for use in bathrooms or other consistently damp areas. This product is only intended for private household use. Do not operate at temperatures over 40 °C (104 °F).

Safety instructions

Notice: Please read this manual carefully before attempting the assembly or installation of your new ceiling fan.
To ensure a safe and successful installation, please make sure to read this manual, ensure it is on hand for your installer to refer to, and keep in a safe place for future reference.

1. ALL electrical work should only be carried out by a suitably qualified and licenced electrical contractor. This ceiling fan MUST be installed ONLY by a suitably qualified and licenced electrical contractor.
2. This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision.
3. Do NOT allow children to play with this appliance, and supervise children around electrical devises at all times.
4. Before commencing any electrical work, ensure the power is disconnected and/or the mains switched off at the circuit box and ensure all pole isolation of the power supply.
5. The fixing point for your ceiling fan must be capable of supporting a 45 kg load.
6. Care needs to be taken to ensure the installation location does not allow the fan blades to come into contact with any object or surface. There must be a minimum of 30 cm clearance between the blade tip (end) and the nearest wall or object. Reduced clearances to walls or ceilings can also reduce the amount of air your fan can move.
7. The installation must also allow for a minimum clearance of 2.3 m between the floor and the bottom of the blades.
8. The fan must be earthed.
9. The fan must be connected to a mains supply only. Fans connected to alternate power systems such as Solar, Wind, Battery etc will not be covered under the terms of this warranty.
10. Use ONLY the EGLO controller supplied with your fan. Use of non-standard or solid-state dimmer type controllers can cause inferior performance, and permanently induce a humming noise in your fan motor which cannot be repaired, and wich will not be covered under warranty.
11. Do NOT change the direction of your fan whilst it is spinning. ONLY change the direction after the fan blades have come to a complete stop.
12. Do NOT insert any object into the fan blades whilst in operation, as this can cause damage to the fan, and personal injury.
13. Do NOT use ceiling fans and gas appliances in the same room at the same time.
14. Only globes specified on the products rating label are to be used in EGLO ventilation products.
15. All EGLO products are warranted to be free from defects in Workmanship and materials provided the products are used with a voltage supply within the range the product is designed to operate.
16. This fan is designed for use indoors only.
17. EGLO lighting will not be liable for any advice given to the consumer from any of our suppliers or third parties, related or otherwise.
18. Proper performance relies on the right fan being correctly installed in the optimum location. Fans that do not perform as expected and which are not faulty cannot be replaced or exchanged under warranty.
19. The important safeguards and instructions in this manual are not designed to cover every possible condition or circumstance. It is understood that common sense, caution and care are factors that cannot be built into the product, those using and maintaining this product must supply these factors.
20. WARNING: If unusual oscillating movement is observed, immediately stop using the ceiling fan and contact the manufacturer, its service agent or suitably qualified persons.
21. The replacement of parts of the safety suspension system device shall be performed by the manufacturer, its service agent or suitably qualified persons.
22. The mounting of the suspension system shall be performed by the manufacturer, its service agent or suitably qualified persons.
23. The fan is to be supplied through a residual current device (RCD) having a rated residual operating current not exceeding 30 mA.
24. The fan is considered to be suitable for use in countries having a warm damp equable climate. It may also be used in other countries.

Before installation

1. Carefully unpack your fan on a soft surface to avoid damage to the fan finish.
2. Do not lay the motor housing on its side, as the decorative housings may become bent or damaged.
3. Check that all parts are present before commencing assembly. Refer to Parts List.
4. If any parts are missing, carefully check the packaging, polyfoam and plastic bags for the missing parts, and if they cannot be located, contact EGLO for assistance before commencing assembly or installation.

Parts list

1. Hanger bracket
2. Receiver
3. Canopy
4. Hanger Ball
5. Downrod
6. Coupling Cover
7. Motor Housing
8. Yoke
9. Cover Bracket
10. DC Motor
11. Blades
12. Light Kit
13. Remote Control

Tools required: Phillips head screwdriver, Flat head screwdriver, Pair of pliers, Wire cutter, Ladder, Wiring supply cable
Note: The use of electric drivers can overtighten the screws and damage threads, DO NOT use power tools for tightening screws.

Selecting a location

1. The ceiling fan must be installed in a location so that the blades are a minimum 300 mm spacing from the tip of the blade, to the nearest objects or walls.

2. The ceiling fan must be installed in a location so that the blades are a minimum 2.3 m above the floor.

3. The fixing point for your ceiling fan must be capable of supporting a 45 kg load. If the location does not have a solid mounting point, you will need to install a timber support between two ceiling joists. Refer to Figure 2.
   Installing the hanging bracket

4. Install the hanging bracket to the ceiling joist or timber support with the long installation screws provided. Pass the screws through the slotted holes in the hanging bracket and secure to the ceiling. Refer to Fig. 3

5. Ensure that at least 30 mm of the screw is threaded into the ceiling joist or timber support.

Note:

• The fixing screws included are designed for use with timber ceiling joists, for all other materials, the appropriate fixing screws will need to be purchased.
• Your fans hanging bracket allows for mounting on angled/sloped ceilings up to a 14-degree pitch.
• The use of electric drivers can overtighten the screws and damage threads, DO NOT use power tools for tightening screws.

Assembling and installing the fan

Important: Check that the power is disconnected and/or the mains switched off at the circuit box to ensure all pole isolation of the power supply.

1. Insert each blade into the upper aligning plate, and secure with 2 screws & washers per blade. Refer to Fig 4.

2. Slide the motor housing over the yoke, and secure with the 3 screws provided. Refer to Fig 5.

3. Insert the downrod into the yoke, and align the holes in the yoke with the holes in the downrod. Insert the bolt through the yoke and attach the R pin onto the bolt. Tighten the screws on the yoke. Refer to Fig 6.

4. Slide the coupling cover over the downrod and place a soft cloth or bubble bag on top to protect the finish. Slide the canopy over the downrod and rest it on the cloth. Slide the hanging ball onto the downrod, and secure it with the screw provided. Refer Fig 7.

5. Re-check that all screws are properly tightened.

6. Carefully lift the fan assembly up to the hanging bracket.

7. Seat the down rod ball assembly into the bracket, ensuring the registration slot of the hanger ball is positioned on the stopper of the hanger bracket to prevent the fan from rotating when in operation. Refer Fig. 8.

8. Wire the ceiling in accordance to; “Wiring Connections”.

9. After completing the mains electrical connection at the terminal block, connect the ceiling fan wiring by connecting the quick connector plugs.

10. Slide the receiver into the ‘slot’ in the hanger bracket. Refer Fig. 9

11. Loosely coil all cables and gently tuck then around the hanger bracket. Raise the canopy up to the hanger bracket, and carefully tuck cables inside the canopy as you slowly raise it to the ceiling. Particular care must be given to ensure that no wires are damaged during this step, especially the remote antenna. Fix the canopy to the hanger bracket with the canopy screws provided.
    Light Kit models only

12. For light kit models, raise the light up to the ceiling fan, and connect the plug connector from the motor with the connector from the light. Align the light kit with the bottom of the blades, push upwards, then revolve clockwise until it locks, ensuring that no wires are damaged during this step. Refer Fig. 10.
    Note: The use of electric drivers can overtighten the screws and damage threads, DO NOT use power tools for tightening screws.

Wiring connections
WARNING: FOR YOUR SAFETY ALL ELECTRICAL CONNECTIONS MUST ONLY BE UNDERTAKEN BY A QUALIFIED AND LICENSED ELECTRICIAN.

Remote Control Working Elements

1. Turn the fan ON/OFF

2. Fan speeds (1=Low, 5=High)

3. LED Indicator light

4. Turn the light ON/OFF

5. Direction of the fan (Reverse)

6. Timer control for the fan

7. 12 V, Type A23 battery for the transmitter
   Inserting the battery into the remote control

8. Open the battery cover.

9. Insert the battery and make sure that the + and – ends are in the correct position. Close the battery cover and press it down until it clicks into place.

Code learning mode

1. To set the code between the transmitter and receiver, learning mode must be activated.
2. Switch the power supply ON, and within 30 seconds, press the FAN ON/OFF button and HOLD IT for 5 seconds. If successful, a long beep will be heard.
   Note: Learning mode will not be activated if the power is on for more than 30 seconds.

Troubleshooting Remote Control
If the transmitter and receiver are not working, or not working properly, check:

• The battery is in the correct position and making good contact, and replace batteries if necessary.
• Is there any other radio frequency or remote-controlled devices nearby, devices using the same frequency can interfere with each device?
• Low voltage in the batteries can affect the operation and signal reception. The LED indicator light will flash when the battery is low, replace the battery immediately.

Note: If not using the fan and remote for extended periods, remove the battery from the transmitter.

Reverse Function

Your ceiling fan can operate either in fan mode or reverse fan mode.
Summer (Forward)
For a cooling effect during summer, your fan should run in a counter clockwise direction, forcing the room air down and outwards creating a wind chill effect that makes you feel cooler.
Winter (Reverse)
During the winter, your fan should run in a clockwise direction at low speed. This will gently draw the warmer air down from the ceiling , balancing the rooms temperature, and allowing you to lower your heating thermostat.

Cleaning and Maintenance

All EGLO ceiling fans need be maintained regularly to ensure performance is maintained.
Your fans natural movement can cause screws to loosen. Every 6 months, check that ALL screws are securely tightened with a screwdriver.
All EGLO ventilation products should be cleaned regularly to insure against corrosion from salt, dust and moisture, both externally and internal (where allowed and possible).
For cleaning, a soft brush or lint-free cloth should be used to prevent scratching the finish. Surface smudges or an accumulation of dirt and dust can easily be removed by using a mild detergent and only a slightly dampened cloth.

Note: Do NOT use abrasive cleaning agents as they may damage the finish.

Troubleshooting

WARNING: CEILING FAN MUST BE SWITCHED OFF AND ISOLATED BEFORE COMMENCING ANY TROUBLE SHOOTING

Wobble/Balance
Please note that all ceiling fans are not the same, even fans of the same model, some may move more or less than others. Movement of a few centimetres is quite acceptable, and does not suggest the fan will fall if installed correctly.
All ceiling fan blades are weighed and grouped by weight. It is impossible to eliminate wobble altogether and should not be considered a fault. Ceiling fans tend to move during operation because they are not generally rigidly mounted.
To reduce the fan wobble:

• Check that all screws which fix the mounting bracket and down rod are tightly secured.
• Wobble may result from inconsistent blade level. Check this by measuring from the tip of the blade to the ceiling, and repeat on every blade.

If the measurements are different;

1. Check that the blade screws are not overly tightened, or loose, causing the tip of the blade to be unlevelled.
2. Out of shaped blades can unbalance the fan and cause wobble. Check by removing all blades and stacking on a flat level surface and ensure all blades are a uniform shape.
3. Interchanging adjacent blades can redistribute the weight and result in smoother operation.

Checklist

Turn power OFF.

Check fuses and circuit breaker. *()**

Loose mains connections to fan.| Turn power OFF.

Check connections at terminal block. *()**

Controller/switch not in correct position.| Turn power OFF.

Check that controller/switch is in the correct position.

Light kit not connected correctly.| Turn power OFF.

Check that light kit plug connector is connected securely. *()**

Fan Wobbles.| Fan blades are not horizontal to the ceiling.| Refer to ‘WOBBLE / BALANCING’ section of this manual.
Blade screws are loose.| Check that all screws are securely tightened. Do NOT overtighten.
Blades are out of shape.| Stack blades on a flat level surface, to ensure all blades are a uniform shape. Contact your retailer for replacement blades.
Fan hanger ball not seated correctly in hanger bracket.| Turn power OFF.

Support the fan very carefully, and rotate the hanger ball to ensu- re the registration slot is positioned on the stopper. *()**

Noisy| Top canopy touching ceiling.| Lower the decorative canopy so that it does not contact the ceiling.
Loose blade screws.| Check that all screws are securely tightened. Do NOT overtighten.
Hanging bracket not installed correctly.| Turn power OFF.

Check and if necessary re-install the hanging bracket if not instal- led/ installed correctly. *()**

Incorrect controller.| Turn power OFF.

Change the controller to the supplied controller. *()**

Fan needs to settle in.| Allow 6-8 hours of operating time to allow fan to ‘settle in’.

May require the assistance of a qualified and licenced electrical contractor.

Disposal
Do not dispose of electrical appliances as unsorted municipal waste, use separate collection facilities. Contact your local council for more information regarding the collection systems available. If electrical appliances are disposed of in landfills or dumps, hazardous substances can leak into the ground water and get into the food chain, damaging your health and well-being.

Technical data

Item number: 35014, 35015, 35016, 35017, 35069, 35071, 35072, 35073
Operating voltage: 220-240 V~ 50 Hz
Total output: 45 Watt
Light Kit: LED, 18 W, 4000 K
Rotational speed: 150 rpm
Dimensions: 35014, 35016, 35069, 35072: Height of body (without pull switch): 15.94 in (300 mm)
35015, 35017, 35071, 35073: Height of body (without pull switch): 15.94 in (330 mm)
Fan diameter: 52 in (132 cm)
Weight: 35014, 35016, 35069, 35072: 8.6 lb (4,7 kg with packaging) 35015, 35017, 35071, 35073: 11.5 lb (5,2 kg with packaging)
Remote Control
Battery: 1 x 12 V, Type A23 (55mA)

EGLO LEUCHTEN GMBH
Heiligkreuz 22
6136 Pill
Austria
www.eglo.com

References

• EGLO | my light. my style.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>