HYGIPLAS CF915 Triple Timer Instruction Manual

HYGIPLAS CF915 Triple Timer Instruction Manual

FEATURES

• Tri-display count down
• Maximum count down / up 23hr 59min 59sec
• 1 / 100 second count up display
• 12 / 24 hours time format
• Foldaway stand
• Magnetic attachment

SPECIFICATION

Maximum Count Down / Up Range

|

23 hours 59 minutes 59 seconds

---|---

Count Down Display Resolution

| 1 second
Count Up Display Resolution|

1 / 100 second

Display Size

| 42(W) x 45(H) mm
Digit Size|

6(W) x 12(H) mm

Battery

| 3 volt, size CR2032 or equivalent x1 piece (included)
Product Size|

61(W) x 118(H) x 17(D) mm

INSTALLATION

1. Slide down battery cover.
2. Install batteries with correct polarity positioning.
3. Put back battery cover.
4. Peel off display protective sheet.
5. Press and hold [CLOCK/TIMER] until display flashing
6. Press [12 / 24] button on the back to select 12 or 24 hours time format.
7. Press [HR], [MIN] and [SEC] to set the correct time.*
8. Press [CLOCK/TIMER] to finish clock setting.

OPERATION

Count Down (Timer):

1. Press [CLOCK/TIMER] to select timer mode.
2. Press and hold [T1] until “TIMER 1” icon flashing.
3. Press [HR], [MIN] and [SEC] to set the desired count down time.*
4. Press [T1] to finish TIMER 1 setting.
5. Repeat above procedures 2-4 to set TIMER 2 and 3.
6. Press [START/STOP/MEMORY] to start all timers’ count down simultaneously.
7. Press the button again to pause.
8. Press the button once more to resume count down.
9. The timer will sound when each setting’s display value becomes 0:00 00 and will be counting up to show the elapsed time.
10. Press [START/STOP/MEMORY] will stop TIMER 1, press the button again will stop TIMER 2 and press the button once more will stop TIMER 3.
11. Press [CLEAR] to clear all values.
12. Press [START/STOP/MEMORY] will display the memorized preset values.
13. To operate each timer individually, Press T1, T2, or T3 respectively to start or stop the timer, or recall the memorized preset values after pressing the [CLEAR] button.

Count Up:

1. Press [CLOCK/TIMER] to select clock mode.
2. Press [CLEAR] to clear display values.
3. Press [START/STOP/MEMORY] to start count up.
4. Press the button again to pause.
5. Press the button to resume count up.

During setting the values, press and hold the [HR], [MIN] or [SEC] button will increase the values automatically.

Compliance

Dispose of depleted batteries in accordance with local regulations, within the EC there are nominated disposal points for batteries.

The WEEE logo on this product or its documentation indicates that the product must not be disposed of as household waste. To help prevent possible harm to human health and/or the environment, the product must be disposed of in an approved and environmentally safe recycling process. For further information on how to dispose of this product correctly, contact the product supplier, or the local authority responsible for waste disposal in your area.

HYGIPLAS parts have undergone strict product testing in order to comply with regulatory standards and specifications set by international, independent, and federal authorities.

HYGIPLAS products have been approved to carry the following symbol:

All rights reserved. No part of these instructions may be produced or transmitted in any form or by any means, electronic, mechanical, photocopying, recording or otherwise, without the prior written permission of HYGIPLAS.
Every effort is made to ensure all details are correct at the time of going to press, however, HYGIPLAS reserve the right to change specifications without notice.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>