Stinger SWITCH HUB SPXSH440 User Guide
- June 6, 2024
- Stinger
Table of Contents
SPXSH440
Quick
Start Guide
PRECAUTIONS
Disconnect the vehicle’s negative battery cable before making any wire
connections.
Protect all vehicle surfaces with tape or plastic.
Do not install components in any location that will hinder vehicle operation,
such as steering wheel, gearshift, airbags, hazard switch.
Bundle cables and harnesses with electrical tape or wire ties to prevent them
from interfering with moving parts.
Never attempt to disassemble or modify the product. Otherwise, an accident,
fire, or electric shock may result.
Exposed wires must be insulated with electrical tape. Otherwise, a short
circuit, fire, or electric shock may result.
To prevent damage to the vehicle, confine the locations of hoses, electrical
wiring, and the fuel tank prior to drilling holes to install this product.
When it is necessary to replace the fuse, always use a fuse of the correct
rating (number of amperes). The use of fuses with higher amperage ratings may
cause a fire.
Overview
SwitchHub is a solid-state relay hub with 4 independent outputs. One 40 amp output and three 20 amp outputs, for a combined total of I 00 amps continuous output. Each output can be independently triggered by a positive or negative trigger. Outputs can be combined for applications that require more than a single output amperage rating. Each output has automatic thermal overload protection with LED status indicators.
Main Power Input – Connect to Battery Positive. An inline fuse should be
used if the power source is over 18″ away.
Module Ground – Connect to Chassis Ground
NEGATIVE Triggers 1-4 – When a Negative(-) signal is applied,
corresponding OUTPUT (1-4) will activate.
POSITIVE Triggers 1-4 – When a Positive (+) signal is applied,
corresponding OUTPUT (1-4) will activate.
Power Outputs 1-4 – When triggered, output + 12V
Examples: When Negative Trigger 3 is grounded, OUTPUT 3 will output+ 12V
When Positive Triggers 1&.2 receive +12V, OUTPUTS 1&2 will output+ 12V
A momentary push-button switch that outputs Ground(-12V) when pressed, is
connected to Negative Trigger 1. OUTPUT 1 is connected to +12V of
horns.
A toggle switch that outputs + 12V when ON is connected to Positive Triggers 3 and 4. OUTPUTS 3 and 4 are connected to + 12V electric fans.
The four positive triggers coming from the SPXM 1 are con need to Positive
Triggers 1-4. OUTPUTS 1-4 are connected to +12V of various accessories.
LIMITED WARRANTY:
Stinger warrants this product to be free of defects in materials and
workmanship for a period of one ( 1) years from the original date of purchase.
This warranty is not transferable and applies only to the original purchaser
from an authorized Stinger dealer in the United States of America only. Should
service be necessary under this warranty for any reason due to manufacturing
defect or malfunction, Stinger will (at its discretion), repair or replace the
defective product with the new or remanufactured product at no charge. Damage
caused by the following is not covered under warranty: accident, misuse,
abuse, product modification or neglect, failure to fol low installation
instructions, unauthorized repair attempts, misrepresentations by the seller.
This warranty does not
cover incidental or consequential damages and does not cover the cost of
removing or reinstalling the unit(s). Cosmetic damage due to accident or
normal wear and tear is not covered under warranty.
INTERNATIONAL WARRANTIES:
Products purchased outside the United States of America are covered only by
that country’s Authorized Stinger reseller and not by Stinger. Consumers
needing service or warranty information for these products must contact that
country’s reseller for information.
Stinger is a Power Brand of AAMP Global
15500 Lightwave
Clearwater, Florida 337 60
P: 888-228-5560
www.stingerelectronics.com
© 2020 Stinger
Technical Support:
Phone: 727-592-5991
Email: support@aampglobal.com
Chat: stingerelectronics.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>