EYLM RFRZ Modern Pendant Light User Guide
- June 6, 2024
- EYLM
Table of Contents
User’s Manual
To get the mobile app, please scan the QR Code above.
http://new.zscbled.com/app/download
Download method:
- Make sure the phone has connected to the network, scan the QR code, click on the page, select the language ( only supports English temporarily).
- Select the Android or iOS version on PC.lamper.(Note: Select the system corresponding to your phone.
Installation Notes
- Working Voltage: AC230V 50HZ
- Please wear appropriate protective safety gloves when installing the lamp
- Do not install the lamp on a damp ceiling
- Please turn off the power during installation and cleaning.
- Please use non-corrosive detergent to clean the lamp if necessary
- We recommend installing in accordance with the instructions
Installation steps
- Remove the hanging plate and install it deep into the ceiling or cement board to ensure its high safety, firmness, and reliability
- Fixed the lamp and ceiling plate, link sub-end, and tightened screws
- Please turn on the power before installation to test the light
- Connect the ceiling mainline
- Align the hanging plate screws, tighten the hanging plate screws
- The installation is completed
This
product can be turned on/off via a remote controller or app installed on your
mobile device. After the EYLM LED Pendant Lamp is successfully connected to
the remote controller or app, you are able to switch to night mode and adjust
the brightness and the light’s temperature.
[Reset to Factory Settings] In order to connect the hanging light with a
new device, delete previous light group settings, or switch between app and
remote-control connection, you need to reset the lamp to factory settings.
[A. Remote Controller:] Press the “ ” button within 5 seconds after
turning on the pendant light. After the lamp blinks once, hold and press the “
” button on the upper left corner until it blinks again. When you see the
light blinking the second time the factory settings reset is complete.
[B.App:] Enter the “ ” section of the app interface. Turn on the light
and tap on “for connecting to Bluetooth devices within 5 seconds after
lighting up. The lamp will blink once. Then turn the light off and on and tap
on “…” on the upper right corner within 5 seconds after lighting up. A window
will pop up afterward and please select “Remove device code”. The hanging
light will blink once more which indicates that the factory settings reset is
complete.
[CAUTION:] If the lamp is not responding to any commands of the remote
controller or app, please turn the light off and on again and repeat the
connection process below.
**Connecting as Single Light
**
[A. Remote Controller:] First, reset to the factory settings. Press the “
” button within 5 seconds after turning on the pendant light. If the light
blinks once connecting was successful. Now you can control the lamp with the
remote controller.
[B.App:] First, reset to the factory settings. Enter the ” ” section of
the app interface and turn on the light and tap on “ ” for connecting to
Bluetooth devices, within 5 seconds after lighting up. If the light blinks
connecting was successful. Go back to the ” ” section to control the pendant
light.
Connecting as individual light groups
[A. Remote Controller:] First, reset to the factory settings. Press on
the “ON” and “OFF” buttons of the light group that you want to set as Group 1
within 5 seconds after turning on the light. If the light blinks connecting
was successful. (5 seconds after the light turned on, press the remote
controller’s “ ” button. If the light blinks the lamp will be set as Group: )
[Adjust connected light groups individually:] Press the “ON” and “OFF”
buttons at the bottom to turn the light groups on and off individually. If you
want to switch to night mode or adjust the brightness and light temperature of
a single light group turn that specific light off and quickly on again and use
the remote controller buttons to adjust.
[B.App:] Set up the light groups within the app. (There are 4 light
groups. If you tap on ” ” one random group will be set up as Group 1.) First,
reset to the factory settings and tap on “for connecting to Bluetooth devices,
within 5 seconds after lighting up. If the light blinks connecting and the
light group set up was successful.
[Adjust connected light groups individually:] Tap on the light group that
you want to adjust to enter the settings window.
Connecting to multiple pendant lamps
[A. Remote Controller:] First, turn all already connected pendant lights
off. Then reset the light that you want to connect to the remote controller to
factory settings. Press on the “ON” and “OFF” buttons of the light group that
you want to set as Group 1 within 5 seconds after turning on the light. If the
light blinks the setup is complete. (5 seconds after the light turned on,
press the remote controller’s “SET UP” button. If the light blinks the lamp
will be set as Group 1)
[B.App:] First, turn all already connected pendant lights off. Set up the
light groups within the app. (There are 4 light groups. If you tap on ” ” one
random group will be set up as Group 1.) Reset the light that you want to
connect to the remote controller to the factory settings and tap on “” for
connecting to Bluetooth devices, within 5 seconds after lighting up. If the
light blinks connecting and the light group set up was successful.
[One lamp can only be included in one control group.] [WARNING:]
- Connecting and operating the lamp via remote controller and app simultaneously is not possible.
- The app is available as an iOS and Android version. Please scan the QR code below or enter [[ new.zscbled.com/app/download]](http://new.zscbled.com/app/download%5D) in a browser and select PC.Lamper in order to download the app. (i0S users can download the app directly from the App Store. Just search for “pc lamper”.
- While operating the lamp via the app, please keep the Bluetooth function on your mobile device and stay within the connection range.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>