IIoT M-7017C Modules User Guide
- June 6, 2024
- IIoT
Table of Contents
- IIoT M-7017C Modules User Guide
- I-7017(F)C, M-7017C Quick Start Guide
- Internal I/O Structure
- Pin Assignments
- Wire Connections
- Modbus Table (M-7017C only)
- DCON Protocol
- Module test and configuration
- Step 1: INIT switch Operation
- 1. Find out the INIT switch( back of the module), and turn to
- 2. Reboot the module
- Step 2: Install & Run DCON Utility
- 1. Please Install DCON Utility first
- You can find the software in the CD. CD path:
- **** Web link:
- **** 2. Run DCON utility
- ****
- ****
- ****
- Step 3: Set search configuration & search module
- Step 4: Select Module for testing and configuration
- Step 5: Configuration Settings & Channel Settings
- Step 6: Change to normal mode and keep the settings
- Trouble Shooting
- Q1. How to do when forgot module address or baud rate?
- Q2. How to configure the I-7000 and M-7000 modules?
- Q3. I-7017(F)C & M-7017C are the current input modules. Do they need
- Q4. How to calibrate the analog input module?
- Q5. How to programming with I-7000 or M-7000 by C#, VB, VC?
- Read More About This Manual & Download PDF:
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
IIoT M-7017C Modules User Guide
I-7017(F)C, M-7017C Quick Start Guide
-
Warranty
All products manufactured by ICP DAS are under warranty regarding defective materials for a period of one year from the date
of delivery to the original purchaser. -
Warning
ICP DAS assumes no liability for damages resulting from the use of this product. ICP DAS reserves the right to change this manual at any time without notification. The information furnished by ICP DAS is believed to be accurate and reliable.
However, no responsibility is assumed by ICP DAS for its use, or for any infringements of patents or other rights of third parties resulting from its use. -
Packing List
** I-7017(F)C or M-7017C**
| Plastic Rail
| CD
| Quick Start Guide
---|---|---|---
Internal I/O Structure
Pin Assignments
Wire Connections
Modbus Table (M-7017C only)
| Address | Description | R/W |
|---|
10129 ~
10136
00129 ~
00136
| Over/under range status of channel 0 to 7 for 4 ~ 20mA or 0 ~ 20mA ranges| R
30001 ~
30008
40001 ~
40008
| Analog input value of channel 0 to 7| R
40481| Firmware version (low word)| R
40482| Firmware version (high word)| R
40483| Module name (low word)| R
40484| Module name (high word)| R
40485| Module address, valid range: 1 ~ 247| R/W
40486| Bits 5:0
Baud rate, 0x03 ~ 0x0A
Bits 7:6
00: no parity, 1 stop bit
01: no parity, 2 stop bit
10: even parity, 1 stop bit
11: odd parity, 1 stop bit
| R/W
Address| Description| R/W
---|---|---
40487| Type code| R/W
40488| Modbus response delay time in ms,
valid range: 0 ~ 30
| R/W
40489| Host watchdog timeout value, 0 ~
255, in 0.1s
| R/W
40490| Channel enable/disable, 00h ~ FFh| R/W
40492| Host watchdog timeout count, write 0
to clear
| R/W
00257| Protocol, 0: DCON, 1: Modbus RTU| R/W
00259| Filter setting, 0: 60Hz rejection, 1:
50Hz rejection
| R/W
00261| 1: enable, 0: disable host watchdog| R/W
00269| Modbus data format, 0: hex, 1:
engineering
| R/W
00270| Host watch dog timeout status, write 1 to clear host watch dog timeout
status
| R/W
00273| Reset status, 1: first read after powered on, 0: not the first read
after
powered on
| R
DCON Protocol
| Functions | Command | Response | Notes |
|---|---|---|---|
| Read module name | $AAM | !AA(Data) | AA: address number |
| Read module firmware version | $AAF | !AA(Data) | |
| Read all analog input data | #aa | >(data) | |
| Read analog input data of each channel (<=16 channel) | #aai | >(data) | i: |
channel number (Hex)
Read analog input data of each channel (>16 channel)| #aaii| >(data)| ii:
channel number (Hex)
If you want to know the detail DCON protocol, please check it from CD or web
CD path: \\napdos\7000\manual\
Web: ftp://ftp.icpdas.com/pub/cd/8000cd/napdos/7000/manual/
Module test and configuration
Step 1: INIT switch Operation
1. Find out the INIT switch( back of the module), and turn to
INIT.
2. Reboot the module
|
Step 2: Install & Run DCON Utility
1. Please Install DCON Utility first
You can find the software in the CD. CD path:
**** Web link:
http://ftp.icpdas.com/pub/cd/8000cd/napdos/driver/dcon_utility/
**** 2. Run DCON utility
****
****
****
---|---
Step 3: Set search configuration & search module
Step 4: Select Module for testing and configuration
Step 5: Configuration Settings & Channel Settings
Step 6: Change to normal mode and keep the settings
- Turn the INIT Switch to Normal.
- Reboot the module
Trouble Shooting
Q1. How to do when forgot module address or baud rate?
Please turn to INIT mode, and run DCON Utility to search. The module supports DCON protocol at the INIT mode.
And the address is 0. The communication setting is “9600,N,8,1”.
Q2. How to configure the I-7000 and M-7000 modules?
ICP DAS provide DCON Utility to configure I-7000 and M-7000 modules.
Please download the last version from: http://ftp.icpdas.com/pub/cd/8000cd/napdos/driver/dcon_utility/
Q3. I-7017(F)C & M-7017C are the current input modules. Do they need
external resistors for the measurement?
No, please refer internal I/O structure.
There is a 125Ω resistor inside for each channel.
Q4. How to calibrate the analog input module?
Usually it is not necessary to calibrate the analog input module.
However, in case you need to perform this operation, we provide a function to calibrate the module. Please refer to user manual 1.10.
Notice:
- Please update DCON Utility to version 2.3 or more.
- Keep the module running more than 30 minutes to warm-up.
Q5. How to programming with I-7000 or M-7000 by C#, VB, VC?
ICP DAS I-7000 and M-7000 series both support DCON protocol. And Only M-7000 series supports Modbus protocol. For DCON protocol, please download SDK and Demo from: http://ftp.icpdas.com/pub/cd/8000cd/napdos/driver/dcon_dll_new/
For Modbus protocol, please refer this web link: http://www.icpdas.com/products/PAC/i-8000/modbus.htm
If there is any other question, please feel free to contact us. Email: [email protected] Website: http://www.icpdas.com.tw/contact_us/contact_us.html