savr E-WCS LED Wall Sconce Installation Guide

savr E-WCS LED Wall Sconce Installation Guide

CAUTIONS

IMPORTANT SAFEGUARDS

When using electrical equipment, basic safety precautions should always be followed including the following:

READ AND FOLLOW ALL SAFETY INSTRUCTIONS

1. DANGER- Risk of shock- Disconnect power before installation. DANGER – Risque de choc – Couper l’alimentation avant l’installation.
2. This luminaire must be installed in accordance with the NEC or your local electrical code. If you are not familiar with these codes and requirements, consult a qualified electrician. Ce produit doit être installé conformément à NEC ou votre code électrique local. Si vous n’êtes pas familier avec ces codes et ces exigences, veuillez contacter un électricien qualifié.
3. SUITABLE FOR WET LOCATIONS. CONVIENT AUX EMPLACEMENTS MOUILLES.
4. WALL MOUNT ONLY. INSTALLATION MURALE SEULEMENT
5. Min. 90°C supply conductors. Les fils d’alimentation 90°C min.

MOUNTING

NOTE: DO NOT remove either top or bottom lens during the installation process. Damage to fixture will occur.
NOTE: Fixture is intended to be mounted over a 3″ or 4″ octagonal junction box.
NOTE: Fixture is equipped with a 120 V driver. Make sure supply voltage is 120 Vac.

1. Remove (2) acorn nuts and sealing washers from front of mounting canopy. See Figure 1.

2.  Pull mounting plate away from mounting canopy.

3. Screw the supplied mounting plate to customer supplied junction box making sure the two threaded studs on the mounting plate fall in the same horizontal plane. A level can be rested across the two studs to verify they are horizontally positioned relative to each other.

4. Gently pull the supply wires through the center hole in the mounting plate.

5. Make wiring connections per ELECTRICAL CONNECTIONS section.

6. Adjust toggle switch inside mounting canopy for light distribution required. Top position (0) is down light only. Bottom position (l) is up/down light. See Figure 2 on the back page.

7. Slide the mounting canopy over the two threaded studs on the mounting plate.
   NOTE: Make sure “THIS END UP” sticker inside mounting canopy is facing upward.

8. Tighten canopy to mounting surface using acorn nuts and sealing washers removed in Step 1.
   NOTE: Sealing washers must be positioned under acorn nuts to ensure a water tight seal.
   NOTE: For wet locations, a high grade caulking material, such as silicone rubber, must be applied around perimeter of mounting canopy at canopy/mounting surface interface.
   
   FIGURE 1

Apply silicon around luminaire perimeter after installtion

INSTALLATION INSTRUCTIONS E-WCS

ELECTRICAL CONNECTIONS

Fixture is equipped with a 120V driver. Make sure supply voltage is 120V AC

1. Connect supply ground and fixture ground (bare) lead to ground screw on mounting plate.
2. Connect supply common to fixture neutral (white) lead.
3. Connect supply Vin (120 VAC) to fixture hot (black) lead. Tuck all wires carefully into wiring chamber ensuring that no wires are pinched.

FCC NOTICE Class B

CAUTION: Changes or modifications not expressly approved could void your authority to use this equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
Changes or modifications not expressly approved could void your authority to use this equipment.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
—Consult the dealer or an experienced radio/TV technician for help. CAN ICES-005 (B)/NMB-005 (B)

Read More About This Manual & Download PDF:

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>