MeTra DP-5859 Dash Panel Kit Installation Guide

June 6, 2024
Metra

MeTra DP-5859 Dash Panel Kit Installation Guide

Visit MetraOnline.com for more detailed information about the product and up-to-date vehicle specific applications

WIRING & ANTENNA CONNECTIONS (sold separately)

  • Wiring Harness: Please visit metraonline.com for wiring harness options.
  • Antenna Adapter: Not required

TOOLS REQUIRED

  • Panel removal tool
  • Phillips screwdriver
  • Socket wrench
  • Cutting tool

Attention! Let the vehicle sit with the key out of the ignition for a few minutes before removing the factory radio. When testing the aftermarket equipment, ensure that all factory equipment is connected before cycling the key to ignition.

KIT FEATURES

  • DDIN radio provisions. (sub-dash modifications are required)
  • Custom textured replacement dash panel to accommodate DDIN radios. Metra suggests painting factory vents black to match the replacement dash panel.
  • Multiple trim panels and brackets to cover multiple trim levels and vehicle options.

KIT COMPONENTS

  • A) Dash panel

  • B) Manual climate panel

  • C) Manual climate brackets

  • D) Auto climate panel

  • E) Auto climate brackets

  • F) 3-position 4WD switch panel

  • G) 4-position 4WD switch panel
    KIT COMPONENTS

  • H) Drive position switch back covers

  • I) Airbag switch panel

  • J) Blank panels (2)

  • K) Panel clips (5)

  • L) #4 x 3/8” Phillips screws (4)

  • M) #8 x 3/8” Phillips screws (16)

APPLICATIONS

Ford

  • Expedition: 1997-2002
  • F-150:   1997-2003
  • F-150 Heritage: 2004
  • F-250: 1998

Lincoln

  • Blackwood: 2002
  • Navigator: 1997-2002

DASH DISASSEMBLY

  1. Unsnap and remove the dash panel. (Figure A)

  2. Remove the factory radio using Metra’s 86-5618 radio removal tools.

  3. Remove the climate controls (recommended for sub-dash cutting). (Figure B)

  4. Remove (2) 7/32” screws and unsnap the factory vents from the dash panel. (Figure C)
    DASH DISASSEMBLY
    If equipped, there is a 3-position or a 4-position drive position switch. Remove switches from factory dash panel:

  5. Remove 4wd knob from front. (Figure D)

  6. (2) 5.5mm screws from the switch. (Figure D)

  7. Grind down 3 tabs to remove the light pipe cover and drive position graphic with icons. Note: Be careful not to cut into the factory drive position graphic, it will be re-used along with the factory light pipe. (clear plastic) (Figure E)

  8. Carefully remove the drive position graphic. (Figure E)
    DASH DISASSEMBLY

  9. If equipped, remove the factory passenger airbag indicator and switch. **(Figure F)

**

KIT PREPARATION

If equipped with the factory drive position switch:

  1. Snap the drive position switch panel into place and secure with (2) factory screws (extra hardware is provided if needed). (Figure A)
    KIT PREPARATION

  2. Place the graphic into the drive position switch panel (either 3 position or 4 position). (Figure B)
    KIT PREPARATION

  3. Place the factory light pipe (clear plastic) into position and then the back cover. (Figure C)

  4. Secure the switch with the remaining factory screws (extra hardware is provided if needed) Install the knob from the front. **(Figure D)

**

If equipped with the factory passenger airbag switch:

  1. Snap the airbag switch panel into place and secure with the factory hardware (extra hardware is provided if needed). (Figure E)
    KIT PREPARATION

  2. Secure the factory switch into place using the factory hardware. (extra hardware is provided if needed). **(Figure F)

**

Select either the manual climate or auto climate trim panel and brackets.

  1. Secure the appropriate climate panel to the dash panel using the (4) supplied #4 x 3/8” screws. (Figure G)

  2. Attach the (5) supplied panel clips to the radio housing. (factory panel clips can be used) (Figure H)
    KIT PREPARATION

  3. Metra recommends painting the vents matte black to better match the replacement dash panel.

  4. Attach the vents to the radio housing using the factory hardware (Figure I)

  5. Cut sub dash area. Top and sides.

  6. Remove rear support. Might need to trim the sub dash bracket (radio opening) (Figure J)

  7. Install the climate controls back into the sub dash.

KIT ASSEMBLY

  1. Attach the appropriate radio brackets to the radio using screws supplied with the radio, and then secure into the dash opening. (Figure A)

  2. Locate the factory wiring harness and antenna connector in the dash, and complete all necessary connections to the radio. Metra recommends using the proper mating adapter from Metra and/ or AXXESS. Re-connect the negative battery terminal and test the radio for proper operation.

  3. Snap the radio trim panel over the radio and reassemble the dash in reverse order of disassembly

Customer Support

Contact our Tech Support line at: 386-257-1187
Or via email at: techsupport@metra-autosound.com

KNOWLEDGEKNOWLEDGE IS POWER
Enhance your installation and fabrication skills by enrolling in the most recognized and respected mobile electronics school in our industry.
Log onto www.installerinstitute.edu or call 386-672-5771 for more information and take steps toward a better tomorrow.

Metra recommends MECP certified technicians

Scan QR Code More Detail:

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals