GIANT RECON E HL600 Lights User Guide
- June 6, 2024
- GIANT
Table of Contents
GIANT RECON E HL600 Lights
Diagram
Warning
- Do not look directly into the light beam or shine it directly into the eyes of other people.
- Do not touch the light case or LED when the light is on as they can become very hot.
- Keep light out of reach of children.
- RECON E HL LED lights have a water resistance rating of IPX6 under regular daily use and are not designed to be submerged in water. Submerging RECON E HL LED lights under water will damage the light and void the warranty.
- Do not attempt to disassemble or repair the light; doing so will void the warranty.
- Be sure to direct the light beam downward to avoid blinding on coming pedestrians or drivers.
- Do not use high mode on public roads.
- Before your ride, please make sure the light is firmly mounted to the bracket, that it functions correctly and is not blocked by baggage, etc.
- In case unexpected light shutoff or battery issues, carrying a spare light is recommended.
- If the light, light case or accessories become dirty with mud or dust, clean them with a soft cloth moistened with mild soap. Never use alcohol, benzene or solvents, doing so will result in damage and voidthe warranty.
- Giant Bicycles does not accept any liability for injuries or other damages resulting from the improper use or improper installation of this product under any circumstance.
INTRO
- To ensure proper use and care of your new RECON EH L LED lights, PLEASE READ ENTIRE MANUAL BEFORE INSTALLATON AND OPERATION.
- Traffic laws mandating bicycle lights vary from country to country. Please make sure you are following the appropriate bicycle light laws and regulations in your country of use.
- RECON EH L LED lights can be controlled via the on-board electronics of your E-bike system and are only to be mounted on E-bikes with DC voltage that have their own battery charge indication and control. The E-bike system must also be capable of automatically shutting the light off when the on-board battery reaches critical voltage to avoid deep battery discharge.
- RECON E HL LED lights are powered by the motor of your E-bike and need to be manually installed. Depending on make and model / battery type, correct installation may require some disassembly of the bike and motor and additional wiring to connect the light to the Please follow the appropriate Giant How-To video for correct installation on your model / battery type or contact thee-bike or motor manufacturer for installation instructions.
NOTE
Incorrect disassembly, installation or assembly may void the warranty of
your e-bike and/ or light. It is highly recommended that a trained E-bike
technician install your lights.
ALIGNING THE RECON EHL BEAM
- Place the bike 5 m away from a wall and face your bike to the wall.
- Turn on the RECON EHL and put it in high-beam mode
- Make sure it is parallel to the ground
- Mark the cut-off line of the beam on the wall, where the beam ends above and is brighter below
- Measure and mark 7 cm below the cut off line above
- Adjust the RECON E HL so that the height of the beam matches the new lower cut off line
NOTE
Make sure to follow the steps above to achieve a glare-free beam that is
compliant with German road law.
CONNECTION
OPTIONALCABLES FOR NON-YAMAHA MOTORS
NOTE
Giant / Yamaha motor cable included. Cables for non-Yamaha motors are not
included and must be purchased separately. Contact your authorized Giant
retailer for more information.
TECHNICAL DATA
- Low Beam – 600 Lumen
- Wattage – 5W
- Input Voltage – 6-48V DC
- Illuminant – 1 LED
- Power Cable Length – 60cm
MOTOR COMPATIBILITY
- Bosch (6V) / Bosch (12V)
- Shimano ES000, E7000, E6100, E6110, E9000
- Shimano E6000, E6001, E6010, E6050
- Shimano E8000, E8080, E6002, E6012
- Yamaha PWse / Yamaha PW
- Brose Drive S (2018)
WARRANTY
- In U.S.A. and U.K., RECON E HL LED Lights carry a two (2) year warranty to the original owner from the original purchase date (proof of purchase required).
- RECON EHL warranties cover all manufacturing defects in materials or workmanship.
- For all warranty issues worldwide, please contact an authorized Giant retailer and present proof of purchase.
- If an LED is not working correctly or not working at all, do not use your light The light will need to be replaced immediately.
- Normal wear and tear or damage arising from improper installation, attempting to access or modify electronics, accidents, misuse, abuse and/or neglect are not covered by the warranty.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>