Wickes 800, 900 and 1000 Base and Corner Base Unit Assembly Instructions
- June 6, 2024
- Wickes
Table of Contents
800, 900 and 1000 Base and Corner Base Unit Assembly
800, 900 and 1000 Base and Corner Base Unit Assembly
TH Note: If fitting a “True Handleless” kitchen, some components will differ
to those shown in this instruction and will also be packaged separately.
Please refer to your True Handleless guide to Receiving for further details on
the different components and difference in installation.
Components
D
G
E
A
C F
A B
Important Information – True Handleless Kitchens Installers: See Note Above TH
Caution: Some pieces of hardware could be hazardous to small children. Keep all these items out of reach and do not leave children unattended in the assembly area. Please read these instructions carefully before proceeding. Refer to the Guide to Receiving and Installing your Kitchen booklet for further information. Note: Due to variation in wall conditions no screws are supplied for fixing the units to the wall. If in doubt consult an expert. Assemble the unit on a clean solid work surface. In the interest of continuing improvements we reserve the right to amend or adjust the specifications without prior notice. Errors and omissions excepted. These units may be fitted with a drawer system. The drawers are supplied separately. These instructions show the runner positions for the drawer system. Follow the instructions supplied with the drawers for drawerbox assembly. Every effort has been made to ensure that this product leaves the factory in perfect condition. In the unlikely event that an item is damaged or incorrect, please contact the customer services department.
FM 665131
Note – Fitting Handles: (1) Decide where you are going to position each handle to maintain symmetry around your kitchen. (2) Measure the handle centres and mark off each door/drawer position. (3) Drill through the door/drawer using a fine drill (<2.5mm), then drill back from the rear face using a 4.5mm drill. (4) Attach with the fixings provided with your handle.
Ref. No. 150101
Item
3.5x12mm
Quantity 14
Ref. No. Item 154027
150202
4x12mm
150201
4x15mm
150199
4.5x45mm
150198 154082
55mm Carcase Screw
16 16/20
154068
154047 4
3 152181
6
154084
1 152162
154085 154004
7
150308
8
150309
Quantity 6
Ref. No. Item 152401
8 152418
2 152402
4 152148
4
151999
2
151500 2
Quantity Tools Required
4/5
5mm
Drill 4/5
2
Medium Crosshead
Screwdriver
4
Large Flathead
12
Screwdriver
2 Spirit Level
G-Clamp (pair)
Hammer
Tape Measure Bradawl
1 2 Assembly Instructions
12
TH Modification required at this stage, see True Handleless guide for further details.
21
98mm Drawer runner
98mm Drawer runner
A
A
12
12
Drawer Runner
21
21
1
34
B
3
Note: Drill centre holes of B
3
and E for Base Units. For
Corner Base Units consult
kitchen plan for door size and
drill accordingly.
3
Scrap wood
4
3
5mm
4
3
4 Scrap wood
3
E
3
3
154085
6
56
5
A
5
5
Front x4
1 x ‘L’; 1 x ‘R’
x2
3.5 x 16mm
Fit as third screw
2
1
154082
7 11
8
2
6
154004
6
45mm 10
9 125mm
11
7D
8
Scrap wood
10 9
8 8
5
B
E 5
5
6
A
5
Do Not Over Tighten
Modification required at this
TH stage, see True Handleless guide for further details.
Start Locked
12 13 Without Drawers
12 13
F
12 13
9
8
150199
4
150101
2
8
9 125mm
150202
2
12
Note: Countersunk screw
goes into back panel D.
154068
2
154004
2
10
150202
45mm
4
10
11
Note: Only drill if drawers are
being fit. Base Units drill as
indicated. Corner Base Units
consult kitchen plan for door size and drill accordingly.
13
Only drill from the lower set
of holes
154047
2
5mm
150198
2
Modification required at this
TH stage, see True Handleless guide for further details.
12
13
14 15 With Drawers
14
G
15
16 17 With Drawers
14
Drawer runner
F
15
14 15
154085
1
154084
18 20 With Drawers
20
18 19
16
1
18
154004
19
150198
18
20
19
150198
Drawer Runner
Front x4
1 x ‘L’; 1 x ‘R’
x2
3.5 x 16mm
Fit as third screw
17
Do Not Over Tighten
Start Locked
21 22
21 21
2
21
2
21 21
22
22
1
22
22
21
4/800 & 900
16/800 & 900
21
152401 5/1000 150201 20/1000
21
22
140mm
18
19
20
23 25 Installation Instructions
23
150202
2 154068
2
82mm
23
Modification required at this
TH stage, see True Handleless guide for further details.
25 23
25 23
24
24
24
5mm
24
150308
2 150309
2
22
4/800 & 900
152418
5/1000
25
25
Appropriate to wall type
(Not supplied)
2
26 29
26
151500
2
26
26
30 31
30
27
27
26
152402 150101
2
28
4
28
28
28
C
29 28
28
28 27
31
Note: Do not over tighten screws
or use a power screwdriver.
31
31
31
28
154027
6
32 35
27 27
= =
32
33
33
C
B
A 33
34
32 34
34
31
31
34
151999
150101
8
36 37 Fixed Fascia Fitting
36
4
71.5mm 36
34
16mm
36
35
150202
2/4
71.5mm 36
16mm 37
37 37
37
Softclose ON Softclose OFF
36
35
154068
2/4
152148
4
34
151999
4/8
32
A 33
33
33
B
C
37 74mm
37
150202
2/4
38 Corner Post Fitting
52mm
55mm Note: Fittings are packed with the Corner Post.
15mm
38
38
38
38
38
15mm
38
38
38
38
Modification required at this
TH stage, see True Handleless
guide for further details.
150124
12
154081
6
39 41 Corner Post Fitting
Modification required at this
TH stage, see True Handleless guide for further details.
Note: Fit corner post to adjacent unit, then fit optional
blanking panel to corner base unit, finally attached corner 40
39 41
post to corner base unit mullion. Use appropriate number
of screws (not supplied). Any excess/hangover does not
need to be trimmed as it will be concealed in the void.
Not Supplied 6-10 150124
6
40 40
40 40
41
41
39
625mm
40
X
Unit Size
Total Length on Plan
41
41
39
41
41
40 40
39 40
40
52mm
55mm
Door Size
39
15mm
41
Unit Size (mm) 800mm 800mm 800mm 1000mm 1000mm 1000mm
Required Door Size (mm) 300 400 500 400 500 600
Total Length in Plan (mm) 925 1025 1125 1025 1125 1225
Void “x” (mm) 125 225 325 25 125 225
Ref. 170801 (05)
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>