MeTra 95-6557B ISO DDIN radio provision Installation Guide

June 6, 2024
Metra

MeTra logo 95-6557B
INSTALLATION INSTRUCTIONS

MeTra 95-6557B ISO DDIN radio provision

Dodge Dakota 2005-2007
Visit MetraOnline.com for more detailed information about the product and up-to-date vehicle specific applications
KIT FEATURES

  • ISO DDIN radio provision
  • Painted scratch-resistant matte black

KIT COMPONENTS

  • A) Radio trim panel
  • B) Radio brackets
  • C) Retaining brackets
  • D) Cut a template
  • E) Philips screws (4)

WIRING & ANTENNA CONNECTIONS (sold separately)
Wiring Harness: Visit metraonline.com for audio/video and steering wheel control interface options.
Antenna Adapter: Not required
TOOLS REQUIRED

  • Panel removal tool
  • Phillips screwdriver
  • 7mm Socket wrench
  • Cutting tool/saw
  • Drill and 1/4 inch drill bit

Attention! With the key out of the ignition, disconnect the negative battery terminal before installing this product. Ensure that all installation connections are secure before cycling the ignition to test this product.

DASH DISASSEMBLY

MeTra 95-6557B ISO DDIN radio provision - Figure

  1. Remove (2) 7mm screws from the inside of the pocket facing upward. (Figure A)
  2.  Unclip and remove the entire trim panel surrounding the radio and climate controls. (Figure B)
  3. Remove (4) 7mm screws securing radio. Unplug and remove the radio. (Figure C)

KIT PREPARATION

Attention! The factory dashboard trim panel and sub-dash will have to be cut to allow the aftermarket radio to fit.

  1. Remove the climate controls from the factory dash panel.

  2. Place the cut template over the panel and mark areas to be cut and the four holes to be drilled. (Figure A)
    MeTra 95-6557B ISO DDIN radio provision - KIT PREPARATION
A

  3. Using a 1/4 inch drill bit, drill the four holes marked from the template.

  4. ith a cutting tool, enlarge the dash panel opening so the radio trim panel fits. (Figure B)
    MeTra 95-6557B ISO DDIN radio provision - KIT PREPARATION
B

  5. Place the radio trim panel onto the dash panel and secure it from the back with the (2) retaining brackets and the included (4) #4 x 3/8” screws. (Figure C)
    MeTra 95-6557B ISO DDIN radio provision - KIT PREPARATION
C

  6.  Remove the two screws at the back of the radio tray. Cut the area shown from the sub-dash to provide the room for the aftermarket radio. (Figure D)
    MeTra 95-6557B ISO DDIN radio provision - KIT PREPARATION
D

KIT ASSEMBLY

  1. Attach the radio brackets to the radio using screws supplied with the radio, and then secure them into the dash opening. (Figure A)
    MeTra 95-6557B ISO DDIN radio provision - KIT ASSEMBLY

  2. Locate the factory wiring harness and antenna connector in the dash, and complete all necessary connections to the radio. Metra recommends using the proper mating adapter from Metra and/ or AXXESS. Re-connect the negative battery terminal and test the radio for proper operation.

  3. Snap the radio trim panel over the radio and reassemble the dash in reverse order of disassembly.



MeTra 95-6557B ISO DDIN radio provision -QR CODEhttp://www.metraonline.com

Having difficulties? We’re here to help.
Contact our Tech Support line at:
386-257-1187
Or via email at: techsupport@metra-autosound.com
Tech Support Hours (Eastern Standard Time)
Monday – Friday: 9:00 AM – 7:00 PM
Saturday: 10:00 AM – 7:00 PM
Sunday: 10:00 AM – 4:00 PM

KNOWLEDGE IS POWER
Enhance your installation and fabrication skills by enrolling in the most recognized and respected mobile electronics school in our industry. Log onto www.installerinstitute.com or call 800-354-6782 for more information and take steps toward a better tomorrow.

Metra recommends MECP certified technicians

Metra. The World’s Best Kits.®
MetraOnline.com
© COPYRIGHT 2021 METRA ELECTRONICS CORPORATION
REV. 8/11/21 INST95-6557B

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals