DMXking eDMX4 PRO ISODIN Interface User Manual
- October 27, 2023
- DMXking
Table of Contents
- INTRODUCTION
- EXTERIOR VIEW
- DEFAULT CONFIGURATION
- CONFIGURATION UTILITY
- PORT TAB
- RECORDER TAB
- DMX DISPLAY FUNCTION
- NODE REPORT
- ART-NET NODE NAME
- FACTORY RESET
- SUMMARY OF SETTINGS
- PORTS, MERGING, PRIORITY AND DMX INPUT
- COMPATIBLE SOFTWARE
- TECHNICAL SPECIFICATIONS
- WARRANTY
- DECLARATIONS (FCC & CE)
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
eDMX4 PRO ISODIN Interface
User Manual eDMX4 PRO ISODIN Interface
User Manual
INTRODUCTION
Thanks for purchasing a DMXking.com product. Our aim is to bring you high
quality products with great features we know you’ll appreciate. We ship only
what’s required which is why there’s no CD or printed manual in the box, this
is part of our commitment to minimizing environmental impact.
This user manual covers features up to v3.13 firmware. Some functionality may
not be available with earlier firmware versions.
HARDWARE AND FIRMWARE VERSIONS
From time to time minor hardware changes occur in our products usually
small feature additions or unseen optimizations. The table below lists eDMX4
PRO ISODIN product variants. Check the product label for P/N details.
Part Number | Feature addition |
---|---|
0118-1.0 | Initial product release |
Firmware updates are released on a semi-regular basis. We recommend updating to the latest available firmware version so all product features are available. Please take note the user manual reflects latest firmware version features unless otherwise noted.
Firmware Version | Comments |
---|---|
v3.5 | Initial release |
v3.6 | Fixed eDMX4 PRO ISODIN port allocation mismatch. “Critical update to |
replace v3.5
v3.7| DMXworkshop excess ArtPoll bytes accepted, Full frame DMX512 option DMX-
IN & DMX-OUT, Broadcast ArtNet playback over network, ArtPollReply includes
UID report, ArtNet fail safe modes, NTP time sync and time zone with DST, DMX-
IN & DMX-OUT re-mapping channel offset, Timeout all sources for DMXIN, sACN
CID fix for multiple DMX-IN ports on same universe, sACN Universe Sync
enhancements, Recording from DMX-IN sources, Default Gateway added to
ArtlpProg, Numerous Record/playback enhancements (see eDMX Recorder manual).
V3.8| ArtPollReply message excess byte trimmed, Volume label report, End of
show playback timing for improved show looping.
V3.9| Improved merge source handling at end of show playback for seamless
looping with merge. Master script final show entry now checks individual show
script.
V3.10| ArtPoll handling fix for Madrix.
V3.11| Alternate ArtNet port added. NTP time sync at startup increased
attempts. DMX-OUT Channel offset with Full Frame option now correctly handled.
RDM Discovery message PortID corrected. RDM message length error corrected.
V3.12| RDM functionality where physical ports have same universe allocated.
YAML configuration file load from SD card. ArtNet universe data accepted from
alternate ArtNet port alongside standard ArtNet port.
V3.13| CRON tab entries expanded to 20. CRON run option to delay start until
NTP response. Special feature request for 24hr long show skip ahead to current
time upon start. Snapshot scene load/update from SD card upon startup.
Snapshot write to SD card file.
MAIN FEATURES
- Wide input power range 8-28Vdc.
- DIN rail mounted compact form factor.
- Static or DHCP IPv4 network addressing.
- Supported operating systems: Any with Ethernet networking support. Windows, MAC OS, Linux, iOS, Android….
- eDMX4 PRO ISODIN – 4x DMX512 Out or DMX512 In with Art-Net, sACN E1.31 and E1.20 RDM support
- Art-Net broadcast, Art-Net II,3 & 4 unicast, sACN/E1.31 Multicast and sACN Unicast support
- Merge 2 incoming Art-Net/sACN streams per output channel with both HTP and LTP options
- Merge Art-Net/sACN + DMX input -> DMX output(s)
- Merge 2x DMX input -> DMX output(s)
- Split 1x DMX input -> 3x DMX outputs
- sACN Priority takeover for multi-tier controller arrangements
- Mix and match ArtNet with sACN merge/priority sources
- DMX-IN and DMX-OUT channel offset re-mapping
- User configuration of Art-Net Node short and long names
- 1500V Isolation between every port
- DMX ports with 3 pin screw terminal plugs.
- E1.11 Higher Protection Level “DMX512-A Protected” device
- Fully compatible with all software and hardware that supports Art-Net I, II, 3 & 4 and sACN protocols
- Works with your existing console if Art-Net or sACN external nodes are supported
- Universe Sync Art-Net, sACN and Madrix Post Sync
- Recording and playback to microSD card (not included). See eDMX PRO Record / Playback manual
- Standalone show playback without computer or network connection
- Internal clock with NTP time sync for timed playback
- Configuration utility with basic Art-Net output/input test functionality
- Accessory port for external show triggering and future add on devices
- Firmware updates can be performed by end user
eDMX4 PRO ISODIN products consider Art-Net 00:0:0 to be Universe 1 (i.e. offset by 1) so there is an easy mapping between sACN/E1.31 and Art-Net.
EXTERIOR VIEW
FRONT VIEW
Network 10/100Mbps RJ45 socket. Pluggable terminal block for 8-28Vdc power
input. Four 3way pluggable terminal block connectors for DMX512.
STATUS LED TABLE
LED | Indication |
---|---|
Protocol | Protocol activity. Flash Yellow = Art-Net/sACN. Solid Yellow = |
Firmware Update mode.
Network| Network activity. Green = Link, Flash = Traffic
DEFAULT CONFIGURATION
All eDMX4 PRO ISODIN units ship with default IP address settings. Please reconfigure network settings as required before use.
Parameter | D efault Setting |
---|---|
IP Address | 192.168.0.112 |
Subnet Mask | 255.255.255.0 |
Default Gateway | 192.168.0.254 |
IGMPv2 Unsolicited Report | Unchecked |
Network Mode | Static IP address |
DMX512 Port configuration parameter defaults.
Parameter | Default Setting |
---|---|
Async Update Rate | 40 [DMX512 frames per second]. Universe Sync will override. |
Port Operation Mode | DMX-OUT |
Timeout all sources | Unchecked |
Channel Offset | 0 |
Fixed IP | 0.0.0.0 [Only for DMX IN — Unicast to 1 IP address only] |
Merge Mode | HTP |
Full DMX Frame | Unchecked |
‘Broadcast Threshold | 10 [Art-Net 11/3/4 unicasting up to 10 nodes]. Set to 0 |
for Art-Net I broadcast on DMX IN ports.
Unicast IP [DMX-1N]| 0.0.0.0
sACN Priority (DMX-IN]| 100
RDM Discovery Period [DMX-OUT]| Os / RDM Disabled
RDM Packet Spacing [DMX-OUT]| 1/20s
DMX-OUT Failsafe Mode| Hold Last
Recall DMX Snapshot at startup| Unchecked
DMX512 Universe| 1-4 [Net 00, Subnet 0, Universe 0-3]
Note: sACN Universe 1 = Art-Net 00:0:0
*Global threshold for all DMX-IN ports, configured in Port A settings tab.
CONFIGURATION UTILITY
The eDMX Configuration utility provides a simple interface to all device
parameters. Typically, these are set once during initial configuration and
left untouched. If you are not confident in setting up network IP Address,
Subnet Mask and Default Gateway parameters please get in touch with your
distributor. DHCP is supported from firmware v2.14 onwards.
From firmware v3.12+ and eDMX Configuration v1.23+ primary Art-Net UDP 6454
and an alternate UDP 16454 port may be used for device configuration. This is
helpful when simultaneously running eDMX Configuration and a lighting control
application.
Automatic selection of alternate port is performed upon utility startup if the
primary Art-Net port is unavailable. It is also possible to lock eDMX
Configuration to the alternate port via the Advanced menu. Note that DMXking
nodes are always listening on both primary and alternate ports so there is no
device configuration required to change.
IMPORTANT: Firmware v3.11 and older. Once you’ve finished configuring your
eDMX product close the configuration utility before starting your lighting
control application if it’s running from the same computer.
From eDMX Configuration v1.24+ an eDMX Node configuration can be saved/loaded
from a simple Key:Value YML file. Select the node and perform Load/Save
accessible in the File menu. Firmware v3.12+ can load configuration from a
file named “conf.yml” off the SD card.
NETWORK TAB
Before starting the eDMX Configuration utility please ensure your computer has
appropriate IPv4 network settings, for example IP 192.168.0.100 Subnet
255.255.255.0 Gateway 192.168.0.254.
Upon startup eDMX nodes are automatically detected and displayed by IP
address. To poll for new devices or just check the communications is okay by
clicking Search. From v1.16 polling is automatic every 8 seconds but can be
disabled through the Advanced | Auto Device Poll menu option. Mute Responses
option prevents any new nodes from being listed regardless of their status on
the network. With large node counts this can be helpful.
Click on the desired node’s entry and all Settings will be retrieved. Note
that if no response is received the settings will be greyed out and no
additional tabs visible. An activity box shows both transmitted and received
messages to help with diagnosing communication issues. If your network
configuration has multiple adapters and or IP addresses you should select the
same network range as the eDMX from the Network Adapter IP Address dropdown
box and also ensure the subnet mask is appropriate.
Utility v1.20 uses Settings Broadcast by default which allows node settings to
be updated regardless of the network adapter subnet range. This only works if
all detected nodes are firmware v3.0+ and is automatically disabled
otherwise.
Unicast single node discovery and configuration is possible by selecting
Advanced | Unicast Poll and entering the destination IPv4 address then click
Search. This will function over routed networks provided a Default Gateway
has been specified in the node Network Settings.
All eDMX/LeDMX/ultraDMX PRO nodes provide IGMPv2 Reports necessary to participate in a multicast environment as necessary for sACN/E1.31 protocol. Sometimes due to network infrastructure issues an IGMP querier is not present and in these situations, you can opt to have the node generate ongoing unsolicited IGMPv2 Reports.
To change the node Network Settings make applicable changes then click Update
Network Settings.
Selecting Firmware Update will prompt for an appropriate firmware file and
upload upon confirmation. A built-in boot loader permits updating of the eDMX
firmware. We do not recommend performing firmware updates over routed
networks. Note only signed encrypted firmware files from DMXking.com can be
successfully loaded to ensure you won’t brick your device by accident. Future
firmware releases for this product will be in the form
0118-500-VersionMajor.VersionMinor.enc
PORT TAB
Port Operation Mode: DMX-OUT
Port Operation Mode: DMX-IN sACN with sACN Priority 100
DMX512 ports can be individually configured as either DMX-OUT, with automatic
dual sACN/Art-Net protocol support, or DMXIN, with manually selected sACN or
Art- Net protocol.
When configured as DMX-IN a single Unicast IP address destination may be
specified but in the majority of applications leaving this field at 0.0.0.0 is
appropriate.
Timeout all sources can be used to override default ArtNet defined behavior of
holding the last sent or received frame forever.
-
DMX-OUT mode: Whenever 2 sources are present and being merged together a 2 source will always timeout when the stream stops. In DMX-OUT mode if Timeout all sources is unchecked and Hold Last mode selected the output will hold last frame forever. Timeout all sources checked and Failsafe Mode other than Hold Last selected will cause the output to change to Zero, Full or Snapshot Scene.
-
DMX-IN mode: An ArtNet or sACN stream is generated upon receiving DMX512 on the port. Timeout all sources checked will cause this stream to end a few seconds after the DMX512 signal stops.
Channel Offset provides simple re-mapping for both DMX-OUT and DMX-IN port configurations. Set to 0 for no re-mapping. -
DMX-OUT mode: Incoming ArtNet or sACN stream(s) are re-mapped so channel 1 is pushed up to channel 1+N. When channel 1+N exceeds 512 the incoming stream channels are ignored/lost.
-
DMX-IN mode: Incoming DMX512 is re-mapped so channel 1 is pushed up to channel 1+N on the outgoing ArtNet or sACN stream. When incoming DMX512 channel 1+N exceeds 512 to channels are ignored/lost.
Make changes to the applicable Port settings then click Update. Changes on all port tabs are updated regardless of which tab the Update button is clicked.
RECORDER TAB
Please refer to the eDMX PRO Recorder manual for more information. This functionality is common to all eDMX PRO, LeDMX PRO and ultraDMX2 PRO devices except eDMX1 PRO which does not include an SD card socket.
DMX DISPLAY FUNCTION
Select View | DMX Display for a simple DMX512 test utility. To generate an
Art-Net output stream click Transmit then select one of the 6 Transmit Options
and change Art-Net Universe as applicable. When in Manual mode you can click
on any of the channels (represented by small boxes with hexadecimal channel
level inside) to set ON level and double click to set zero. The mouse scroll
wheel adjusts a channel by a defined increment. Channel number increases left
to right, top to bottom and the roaming tool tip provides information about a
specific channel.
Both the ON level and mouse wheel step can be set by right clicking anywhere
within the black display area. Number of channels transmitted and the refresh
rate can be adjusted using the applicable sliders adjacent to transmit
options.
Changing to Receive mode will display the selected Art-Net universe number
with merged streams if more than 1 is present.
Note Art-Net II unicast is not supported meaning only Art-Net broadcast
streams are displayed.
The DMX Display utility works with any manufacturers Art-Net hardware and can be useful for diagnostics and simple testing of DMX512 fixtures.
NODE REPORT
From firmware v3.3+ each node provides a brief status report indicating DMX frame rates, SYNC status, SHOW playback selection and RECorder status.
Above an eDMX4 PRO reports Port A,B,C,D at 40fps with no synchronization present (Async mode) and the recorder state Idle.
In the example above the recorder status indicates there is No SD card present.
ART-NET NODE NAME
The Art-Net protocol supports device naming which can make larger installations more manageable. Both Short Name (17 characters) and Long Name (63 characters) for an eDMX Device can be edited in the Node Information box.
FACTORY RESET
This is a last resort option if for whatever reason incorrect or forgotten
device network settings have rendered your device unusable. A word of warning
– this function will factory reset ALL eDMX devices on your network so it’s
critical to separate off the device requiring reset. We recommend directly
connecting a computer and eDMX device using a network cable so there’s no
chance of additional eDMX devices accidentally being reset too.
Several warnings are presented before the command is sent. This function is
not intended for use with eDMX/LeDMX PRO and ultraDMX2 PRO devices and will
not have any effect in firmware 3.0+.
SUMMARY OF SETTINGS
Parameter | Usage |
---|---|
MAC Address | Factory programmed Ethernet MAC address |
IP Address | IPv4 network address |
Subnet Mask | Subnet mask, typically 255.0.0.0, 255.255.0.0 or |
255.255.255.0 for class A,B & C respectively
Default Gateway| Address of network gateway (router) for communications beyond
local subnet
Network Mode| DHCP or Static IPv4
IGMPv2 Unsolicited Report| IGMPv2 Report messages sent at 5-255 second
intervals
Port Operation Mode| DMX-IN Art-Net, DMX-IN sACN, DMX OUT (both Art-Net and
sACN are always enabled). Fixed IP is 0.0.0.0 by default which equates to
multicast sACN or automatic unicast/broadcast Art-Net. Setting a Fixed IP
forces DMX-IN ArtNet or sACN unicast to 1 IP only.
Timeout all sources| Last Art-Net or sACN stream source if lost will timeout
DMX-OUT. Loss of DMX-IN signal will timeout outgoing ArtNet or sACN stream.
Channel Offset| Re-mapping for DMX-OUT or DMX-IN streams
Async Update Rate| DMX512 output frame rate/frequency. Universe Sync takes
precedence.
Merge Mode| HTP (Highest Takes Precedence – dimmers), LTP (Last Takes
Precedence – moving lights)
Full DMX Frame| Force DMX-OUT or DMX-IN to full 512 channel frames with zero
levels filling gaps
Broadcast Threshold| 0 = Force Art-Net broadcast mode, > 0 Art-Net II/3/4
unicast until threshold (DMX-IN)
Unicast IP| Single IPv4 destination for unicast ArtNet or sACN from DMX-IN
sACN Priority| DMX-IN sACN Priority value assigned to sACN stream. 0 – 200,
default 100
RDM Discovery Period| Number of seconds between internally initiated RDM
Discovery attempt. Setting Discovery Period = 0s will disable RDM
RDM Packet Spacing| Number of 1/20sec intervals enforced minimum between RDM
messages on DMX line
DMX-OUT Failsafe Mode| ArtNet failsafe mode selection. Timeout All Sources
must be checked for all options other than Hold Last.
Recall DMX snapshot at startup| Recall snapshot scene at power on and output
until Art-Net or sACN stream received. Snapshot DMX button records current DMX
output to snapshot memory.
DMX Universe| sACN 1-63999 which is translated to an Art-Net Port-Address
(Net:Sub:Uni). Setting DMX Universe = 1 results in sACN Universe = 1 and Art-
Net 00:0:0 (Universe 1 = Art-Net Universe 0)
PORTS, MERGING, PRIORITY AND DMX INPUT
PORTS AND MERGING
Each DMX Port is fully independent which allows for configurations including
setting multiple ports to the same universe. A commonly used configuration for
eDMX4 PRO ISODIN is 4x isolated DMX512 outputs of the same universe, thus
turning the eDMX4 into a 1 universe Art-Net/sACN node + 4 port isolated
splitter.
eDMX PRO nodes are capable of several advanced merging and stream selection
functions usually only found on higher priced equipment. Support for both HTP
(Highest Takes Precedence) and LTP (Latest Takes Precedence) merging of 2
sources producing a single DMX512 output thus permitting 2 controllers to
simultaneously operate on 1 lighting rig. To achieve DMX stream merging
simply send 2 Art-Net or sACN streams on the same Universe and configure the
applicable DMX OUT port merge scheme HTP or LTP. If the number of sources
exceeds 2 only the first 2 will be processed and all new streams that appear
are simply dropped. Possible merging sources are:
Source | Notes |
---|---|
Art-Net I, II, 3 or 4 | Priority 100 is assigned to permit Art-Net + sACN |
merge/priority functionality.
sACN / E1.31| Only sACN sources of the same Priority will be HTP or LTP
merged.
DMX-IN Art-Net| Configure DMX-IN port universe to match a DMX-OUT port
universe. Priority is locked to 100 since Art-Net does not have a Priority
value.
DMX-IN sACN| Configure DMX-IN port universe to match a DMX-OUT port universe.
Priority is defined by the port configuration sACN Priority.
SUPPORTED MERGING COMBINATIONS
S ourc e 1 | S ourc e 2 | No tes |
---|---|---|
Art-Net | Art-Net | Sources are timed out 3 seconds after last received frame. |
sACN / E1.31 | sACN / E1.31 | Sources will end immediately upon sACN stream |
termination flag, otherwise 3 second timeout after last received frame.
Art-Net| sACN / E1.31| Art-Net source timed out 3 seconds after last received
frame, sACN stream termination flag otherwise 3 second timeout after last
received frame.
DMX-IN| Art-Net| Merge external DMX512 source with incoming Art-Net stream.
DMX-IN| sACN / E1.31| Merge external DMX512 source with incoming sACN stream.
DMX-IN (1)| DMX-IN (2)| Merge 2 external DMX512 sources. Priority is defined
by the respective port configuration sACN Priority.
SACN / E1.31 PRIORITY
At any time if a higher priority sACN stream, on the same Universe, is
received it will take over control a DMX-OUT port regardless of other incoming
streams or merging. When an sACN stream is stopped gracefully via a stream
terminate message the eDMX port will immediately revert to whatever other
sources are present, otherwise the default stream timeout of 3 seconds
applies. If you want to HTP/LTP merge two sACN streams together they must be
of the same priority.
SACN / E1.31 PRIORITY – DMX RECEIVE
When a port is configured for DMX-IN sACN operation the sACN Priority can be
set. This permits DMX Inputs to generate sACN multicast or unicast streams
with a specific priority.
DMX512 IN–UNICAST/BROADCAST/MULTICAST
When you feed a DMX512 signal into an eDMX Port configured as DMX-IN Art-Net
the following will determine Art-Net unicast or broadcast:
- If Broadcast Threshold = 0 the frame is always broadcast on the IP subnet.
- If Broadcast Threshold > 0 and number of detected Art-Net II/3/4 devices “subscribed” to that universe is less than the threshold the frame is unicast to each device.
- If Broadcast Threshold > 0 and the number of detected Art-Net II/3/4 devices “subscribed” to that universe is greater than the threshold the frame is broadcast on the subnet.
- If Broadcast Threshold > 0 and zero Art-Net II/3/4 devices are “subscribed” to that universe the frame is broadcast on the subnet.
- If Fixed IP is not 0.0.0.0 the frame is only unicast to the specified IPv4 address.
As you can see there are multiple ways broadcast could occur. The implementation is done like this to ensure compatibility with mixed Art-Net I/II/3/4 device networks but still permit unicast when Art-Net II/3/4 devices are used exclusively.
For DMX-IN sACN multicast frames will be generated when Fixed IP is 0.0.0.0 otherwise frames are unicast to the specified destination.
COMPATIBLE SOFTWARE
Art-Net/sACN and DMX512 are the most commonly used lighting control protocols
with roots in simple theatrical light dimming.
These days almost any lighting or stage effect equipment may be controlled
using DMX512 (with explicit exclusion of anything involving potentially
dangerous operations such as pyrotechnics) including moving lights, LED
screens, fog machines and laser displays.
The DMXking.com eDMX4 unit is a 4 universe Art-Net/sACN device designed for
use with computer based show control software or expansion of lighting console
outputs. It replaces an entire lighting console allowing the user to perform
sophisticated shows with little more than a laptop. There are many free and
commercial software packages available and by selecting Art-Net as your DMX
device compatibility is guaranteed.
Check the following page for a short list of compatible software:
http://dmxking.com/control-software
TECHNICAL SPECIFICATIONS
- Dimensions: 22.5x100x120mm (WxHxD)
- Weight: 0.15kg
- DC Power input 8-28Vdc, 2.5W max. Typical current consumption @ 12Vdc 250mA
- DMX512 connector: 3 way screw terminal block.
- 1500V isolation on each port.
- Ethernet 10/100Mbps Auto MDI-X port.
- Internal DMX512-A line biasing termination as per ANSI E1.20 RDM requirements
- Art-Net, Art-Net II, Art-Net 3, Art-Net 4 and sACN/E1.31 support.
- ANSI E1.20 RDM compliant with RDM over Art-Net.
- Universe Sync Art-Net, sACN and Madrix Post Sync.
- Both HTP and LTP merging of 2 Art-Net streams per port
- sACN Priority
- Internal merging capability with DMX In and DMX Out ports on same Universe.
- IPv4 Addressing
- IGMPv2 for multicast network management
- DMX512 Frame Rate: Adjustable per port
- DMX512 Port Electrical Protection: DMX512-A Protected as per E1.11-2008
- Operating temperature -10°C to 50 °C non-condensing dry environment
WARRANTY
DMXKING.COM HARDWARE LIMITED WARRANTY
What is covered
This warranty covers any defects in materials or workmanship with the
exceptions stated below.
How long coverage lasts
This warranty runs for one year from the date of shipment from an authorized
DMXking.com distributor.
What is not covered
Failure due to operator error or incorrect application of product. Opening the
unit voids the warranty.
What DMXking.com will do
DMXking.com will repair or replace, at its sole discretion, the defective
hardware. Return shipping costs from our service facility in New Zealand shall
be free of charge.
How to obtain service
Contact DMXking.com directly by email
sales@dmxking.com
DECLARATIONS (FCC & CE)
FEDERAL COMMUNICATIONS COMMISSION (FCC) DECLARATION OF CONFORMITY
Responsible Party:
JPK Systems Limited
PO Box 493
Pukekohe 2340
New Zealand
declares that the product eDMX4 PRO ISODIN complies with Part 15 of the FCC
rules.
Operation is subject to the following two conditions: (1) This device may not
cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a class
B digital device, pursuant to Part 15 of the FCC rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
EEC DECLARATION
We
JPK Systems Limited
PO Box 493
Pukekohe 2340
New Zealand
declare under our sole responsibility that our product eDMX4 PRO ISODIN
conforms to the requirements of Council Directives 89/336/EEC and 73/23/EEC
and therefore complies with the requirements of Council Directive 73/23/EEC,
(The Low Voltage Directive) on the harmonisation of the laws of Member States
relating to electrical equipment designed for use within certain voltage
limits as amended by Article 13 of Council Directive 93/68/EEC
- EN 55103-1
- EN 55103-2
- EN 60065
Signed: Jason Kyle
Date: 1 November 2018
Position: Managing Director
DMXking.com
JPK Systems Limited
New Zealand
0118-700-3.13
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>