DMxking com eDMX2 MAX Ethernet DMX Adapter 2 Universe PoE USB Controller User Manual

June 1, 2024
DMxking com

eDMX2 MAX

USER MANUAL

INTRODUCTION

Thanks for purchasing a DMXking product. Our aim is to bring you high quality products with great features we know you’ll appreciate. DMXking MAX series devices are Art-Net and sACN/E1.31 protocol compatible designed for use with computer based show control software or expansion of lighting console outputs. There are many free and commercial software packages available. http://dmxking.com/control-software

HARDWARE AND FIRMWARE VERSIONS
From time-to-time minor hardware changes occur in our products usually small feature additions or unseen optimizations. The table below lists eDMX4 MAX product variants. Check the product label for P/N details.

Part Number Feature addition
0133-1.0-3 Initial product release. 3pin XLR
0133-1.0-5 Initial product release. 5pin XLR

Firmware updates are released on a semi-regular basis. We recommend updating to the latest available firmware version so all product features are available. Please take note the user manual reflects latest firmware version features unless otherwise noted.

Firmware Version Comments
V4.5 Initial release. RDM support disabled.
V4.6 Art-Net TimeSync. ArtPollReply changed to single universe per message.

Art-Net RDM functionality enabled. DMX512 timing parameters adjustable. Art- Net UDP Port adjustable. Art-Net RDM Controller optional fixed IP and adjustable UDP Port. Diagnostics messages priority enhancements.
V4.7| SD card detection improvements.

MAIN FEATURES

  • Power over Ethernet 802.3af/at compliant. Alternative power via USB-C
  • Tough metal enclosure with multiple mounting options
  • Available with 3 pin or 5 pin XLR socket options
  • Static or DHCP IPv4 network addressing
  • USB DMX functionality in addition to Network ArtNet/sACN
  • Supported operating systems: Windows, MacOS, Linux, iOS, Android
  •  eDMX2 MAX – 2x DMX512 OUT or DMX512 IN with Art-Net, sACN E1.31 and E1.20 RDM support
  • Art-Net broadcast, Art-Net II,3 & 4 unicast, sACN/E1.31 Multicast and sACN Unicast support
  • Merge 2 incoming Art-Net/sACN streams per output channel with both HTP and LTP options
  • Merge Art-Net/sACN + DMX input -> DMX output(s)
  • Merge 2x DMX input -> DMX output(s)
  • sACN Priority takeover for multi-tier controller arrangements
  • Mix and match ArtNet with sACN merge/priority sources
  • DMX-IN and DMX-OUT channel offset re-mapping
  • User configuration of Art-Net Node short and long names
  • Fully compatible with all software and hardware that supports Art-Net I, II, 3 & 4 and sACN protocols
  • Works with your existing console if Art-Net or sACN external nodes are supported
  • Universe Sync Art-Net, sACN and Madrix Post Sync
  • Recording and playback to microSD card (not included). See eDMX MAX Record / Playback manual
  • External show trigger I/O port
  • Standalone show playback without computer or network connection
  • Internal clock with optional battery backup for timed playback. NTP time sync
  • Configuration utility with basic Art-Net output/input test functionality

eDMX MAX translates Art-Net 00:0:0 to Universe 1 (i.e. offset by 1) so there is an easy mapping between sACN/E1.31 and Art-Net.

EXTERIOR VIEW

FRONT VIEW

SD card push-push socket for microSD. Two Neutrik XLR connectors for DMX512 3pin or 5pin options available.
REAR VIEW

Power over Ethernet 802.3af / network 10/100Mbps RJ45 Ethercon socket. USB-C socket for DC power input alternative to PoE.
10way IDC socket for I/O triggering. See eDMX MAX Recorder Manual.
STATUS LED TABLE

LED Indication
Protocol Protocol activity. Flash Red = Art-Net/sACN. Solid Red = Bootloader

mode
Link/Act| Network activity. Green = Link, Flash = Traffic
Power| Incoming power good
SD Card| SD card activity
Port A| DMX512 Port A TX/RX activity
Port B| DMX512 Port B TX/RX activity

USB DMX OPERATION

DMXking MAX series devices include USB DMX functionality alongside Ethernet lighting protocols ArtNet/sACN.
SOFTWARE COMPATIBILITY
Software packages for USB DMX use either a Virtual COM Port (VCP) driver or FTDI specific D2XX driver. DMXking MAX series uses VCP which is more universal than FTDI D2XX, especially across different operating systems, however this has created some
compatibility issues with existing software packages using the later. We are working with software developers still using D2XX to encourage updating their code to utilize VCP instead and also leverage DMXking USB DMX protocol extensions that allow multiple universe operation.
Check https://dmxking.com/ for DMXking MAX series USB DMX compatible software list.
DEVICE CONFIGURATION
Previously DMXking USB DMX capable devices did not require DMX port configuration for DMX-IN mode as this was automatically selected by certain USB DMX messages. This has changed in DMXking MAX series devices which now require explicit DMX-OUT or DMX-IN port configuration along with selecting which port to forward over USB DMX to allow multi-port devices to function with complete flexibility.
DMX PORT MAPPING
Simple USB DMX protocol output messages are automatically mapped to the physical DMX512 ports regardless of configured universe.
USB DMX SERIAL NUMBER
For software compatibility reasons a BCD serial number is calculated from the MAX device hardware MAC address using the lower 3 hexadecimal bytes converted to a decimal number. Software that has been updated for MAX series devices will display the hardware MAC address.

DEFAULT CONFIGURATION

All eDMX4 MAX units ship with default IP address settings. Please reconfigure network settings as required before use.

Parameter Default Setting
IP Address 192.168.0.112
Subnet Mask 255.255.255.0
Default Gateway 192.168.0.254
IGMPv2 Unsolicited Report Unchecked
Network Mode Static IP address

DMX512 Port configuration parameter defaults.

Parameter Default Setting
Async Update Rate 40 [DMX512 frames per second]. Universe Sync will override.
Port Operation Mode DMX-OUT
Timeout all sources Unchecked
Channel Offset 0
Fixed 1P 0.0.0.0 Only for DMX IN — Unicast to 11P address only]
Merge Mode HTP
Full DMX Frame Unchecked
‘Broadcast Threshold 10 [Art-Net 11/3/4 unicasting up to 10 nodes]. Set to 0

for Art-Net I broadcast on DMX IN ports.
Unicast 1P (DMX-IN]| 0.0.0.0
sACN Priority [DMX-IN]| 100
RDM Discovery Period [DMX-OUT]| Os / RDM Disabled
RDM Packet Spacing [DMX-OUT]| 1/20s
DMX-OUT Failsafe Mode| Hold Last
Recall DMX Snapshot at startup| Unchecked
DMX512 Universe| 1-4 [Net 00, Subnet 0, Universe 0-3]
Note: sACN Universe 1 = Art-Net 00:0:0

*Global threshold for all DMX-IN ports, configured only in Port A settings tab.

CONFIGURATION UTILITY

Download eDMX MAX Configuration Utility from https://dmxking.com/downloads- list
User manual for the utility https://dmxking.com/downloads/eDMX MAX Configuration Utility User Manual (EN).pdf

TECHNICAL SPECIFICATIONS

  • Dimensions: 80mm x 39mm x 95mm (WxHxD)
  • Weight: 250 grams
  • Power input: 802.3af/at Power over Ethernet. Maximum power budget 5W.
  • USB-C power input. Any USB power source, only 5V supply is negotiated.
  • DMX512 connector: 5pin or 3pin Neutrik XLR socket
  • DMX512 ports electrically isolated.
  • Ethernet 10/100Mbps Auto MDI-X port Neutrik Ethercon socket
  • Internal DMX512-A line biasing termination as per ANSI E1.20 RDM requirements
  • Art-Net, Art-Net II, Art-Net 3, Art-Net 4 and sACN/E1.31 support.
  • ANSI E1.20 RDM compliant with RDM over Art-Net. Not available in firmware 4.5
  • Universe Sync Art-Net, sACN and Madrix Post Sync.
  • Both HTP and LTP merging of 2 Art-Net streams per port
  • sACN Priority
  • Internal merging capability with DMX In and DMX Out ports on same Universe.
  • IPv4 Addressing
  • IGMPv2 for multicast network management
  • DMX512 Frame Rate: Adjustable per port
  • Operating temperature 0° C to 40° C non-condensing dry environment

WARRANTY

DMXKING HARDWARE LIMITED WARRANTY
What is covered
This warranty covers any defects in materials or workmanship with the exceptions stated below.
How long coverage lasts
This warranty runs for two years from the date of shipment from an authorized DMXking distributor.
What is not covered
Failure due to operator error or incorrect application of product.
What DMXking will do
DMXking will repair or replace, at its sole discretion, the defective hardware.
How to obtain service
Contact your local distributor https://dmxking.com/distributors

ACKNOWLEDGEMENTS

Art-Net™ Designed by and Copyright Artistic Licence

DECLARATIONS

The eDMX2 MAX has been tested against applicable standards and certified compliant as below.

Standard|
---|---
IEC 62368-1| Audio/Video and ICTE Safety Requirements
IEC 55032| Radiated Emissions
IEC 55035| EMC Immunity Requirements
FCC Part 15| Radiated Emissions
RoHS 3| Restriction or Hazardous Substances
Certification| Country
---|---
CE| Europe
FCC| North America
RCM| New Zealand / Australia
UKCA| United Kingdom

DMXking.com • JPK Systems Limited • New Zealand
0133-700-4.7

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals