KINGSTON KB8951NDL Brass NuvoFusion Double Handle 4 to 8 Inch Mini Widespread Lavat Instruction Manual
- June 4, 2024
- Kingston
Table of Contents
INSTALLATION INSTRUCTIONS
Widespread Lavatory Faucet with or without Pop-Up
BEFORE BEGINNING INSTALLATION:
-
Flush plumbing lines to clear any debris.
-
Shut off both supply lines after flushing.
-
Remove the tee connector and spout mounting hardware from the spout.
-
Sparingly apply a small bead of silicon caulking around the center hole on top of the sink (do not use Plumber’s Putty as it may damage the finish and void the warranty).
-
From the top of the sink insert the spout base ring (if applicable) and spout through the center hole. Slip the spout mounting hardware back onto the spout, and hand tighten the lock nut. Insert the pop-up rod through the hole in the back or top of the spout. (see pop-up installation below). Rotate the metal washer, to insure smooth movement of the pop-up rod. Tighten the brass lock nut, and test the pop-up rod for ease of operation.
-
Place the tee connector washer and thread the tee connector on to spout shank.
-
Hot and Cold Stem assemblies are easily Identifiable by a Red(Hot) or Blue(Cold) band, insert stem assembly through side holes from below making sure to have the bottom nut and metal washer threaded on the stem assembly.
-
While holding from under the sink install trim ring and thread escutcheon on to stem assembly, and adjust to a suitable height to allow sufficient space for the handle to operate smoothly. Tighten the bottom nut, please make sure to align the direction of lever handles before tightening the stem.
Warning!!!
Do not over-tighten the nut during installation,
• Over-tighten may crack the valve and cause a severe leak
Need Tools:
-
Attach flexible hoses to the outlet port of hot and cold valve assembly, you may need to loop the hoses as shown on the graphic and be cautious not to over-tighten. Teflon tape not to overtighten.
-
Apply Teflon tape on all male threading and install inlet supply lines (not included) to the bottom inlet port of the hot and cold valve assembly.
-
Install Pop-up assembly as per instructions below. Install the flange body up through the drain opening, hold the drain flange body in position with the pivot rod opening facing the back of the sink and hand tighten the mounting nut.
-
Place pivot rod into pivot rod opening. Slide the pivot nut over the pivot rod and thread it on the drain body. Tighten firmly.
-
Guide the pivot rod through one of the holes on the lift rod strap and secure it with the spring clip. Then adjust the height of the lift rod by resetting the clevis screw. With the lift rod in position on the faucet, insert lift rod through the lift rod strap and secure it with the clevis screw
-
Remove the aerator and tum on both hot and cold valves, let the water run for at least one minute, this will clear any debris left in the line, reinstall the aerator.
CARE AND MAINTENANCE OF YOUR FAUCET
Your Kingston Brass faucet has been finished to the most strict standards;
however, due to the high content of minerals in the water, your finish may
appear dull and tarnished after time. These are some do’s and don’ts to
maintain the luster of your faucet for many years to come.
DO
- Use silicon-based caulking when installing.
- Clean your faucet with only a mild soap and water solution.
- Dry your faucet after using it.
- Give it a coat of Carnauba Wax periodically.
DON’T
- Use plumbers putty when installing the faucet.
- Use any abrasive cleaning agents.
It may seem like a very simple and short list but it is that simple to maintain your faucet, looking shiny and new.
If your faucet is already looking somewhat dull and tarnished, before replacing it, try cleaning it with a 50/50 solution of vinegar and water, you may need to soak some rags and wrap around those stubborn areas, leave overnight and rinse completely in the morning, apply Carnauba wax once you have removed the mineral deposits.
Kingston Brass™ Faucets
(10) YEARS LIMITED WARRANTY
Kingston Brass warrants its faucets to be flawless during normal residential
use. If the faucet should leak or drip during normal use, Kingston Brass will,
free of charge, mail to the original owner the cartridge necessary to put the
faucet in good working condition. All warranty parts to be shipped freight
prepaid ground service. The customer will be responsible for all warranty part
freight charges if express shipping is requested. This warranty applies only
to Kingston Brass Faucets installed in the United States of America only.
Kingston Brass also warrants all other aspects of the faucet or accessories
(except Oil Rubbed Bronze and Dark Bronze Finishes on color changes as part of
the normal living finish behavior) to be free of defects in material and
workmanship during normal residential use within (10) years from the date of
purchase to its original owner. If a defect is found in normal residential
use, Kingston Brass will, at its election, repair, provide a replacement part
or product, or make appropriate adjustments. Damage to a product caused by
accident, misuse, or abuse is not covered by this warranty. Improper care and
cleaning will void the warranty. Proof of purchase (original sales receipt)
must be provided to Kingston Brass with all warranty claims. Kingston Brass is
not responsible for labor charges, installation, or other incidental or
consequential costs. In no event shall the liability of Kingston Brass exceed
the purchase price of the faucet.
SPECIAL FINISHES:
Warranty does not apply to special or living surface finishes such as Oil
Rubbed Bronze, Dark or Old Bronze as living finishes will change over time as
a result of a normal process and may look different than at the time of
purchase, therefore these items are warranted for functionality only. Oil
Rubbed Bronze, Dark or Old Bronze components may vary in the shade at the time
of shipment. This warranty is limited to the replacement of defective parts
only, labor charges and/or damage resulting from improper installation,
repair, or replacements, as well as incidental and consequential damages
connected therewith, are excluded. Any damage to this faucet as a result of
misuse, abuse, neglect, accident or improper installation or any use not
consistent with the instructions furnished by us, will void this warranty.
CAUTION!!!
- Prior to installing the faucet, water lines must be flushed clean of debris and particles that may be present to avoid the clogging of cartridges or aerators causing mal-function, leakage or reduction in flow.
- Warranty will be void if water lines are not properly flushed prior to installing the faucet.
- Use of abrasives cleaners of any strength may damage the finish of your faucet and will void this warranty.
To obtain warranty service, contact the Dealer, Plumbing Contractor, Home Center or E-tailer, or contact
Kingston Brass by calling 1-877-252-7277 or writing to Attn: Warranty Department, 12775 Reservoir Street,
Chino, CA 91710.
Kingston Brass™ Cast Iron Tubs, Acrylic Tubs, Toilets, Vessel Sinks, Wash
Basins, and Stainless Steel Sinks. ONE-YEAR LIMITED WARRANTY KINGSTON BRASS
Sinks, tubs, and toilets are warranted to be free of defects in material and
workmanship for one year from the date of installation. Kingston Brass will,
at its election, repair, replace or make appropriate adjustments where
Kingston Brass inspection discloses any such defects occurring in normal usage
within one(1) year after purchase to its original owner. Proof of purchase
(original sales receipt) must be provided to Kingston Brass with all warranty
claims. Kingston Brass is not responsible for removal or installation costs.
Use of in-tank toilet cleaners will void the warranty. To obtain warranty
service, contact the Dealer, Plumbing Contractor, Home Center, or E-tailer, or
contact Kingston Brass by calling
1-877-252-7277 or writing to Attn:
Warranty Department, 12775 Reservoir Street, Chino, CA 91710. Some
states/provinces do not allow limitations on how long an implied warranty
lasts, or the exclusion or limitation of special, incidental or consequential
damages, so these limitations and exclusions may not apply to you. This
warranty gives you specific legal rights. You may also have other rights which
vary from state/province to state/province. Never use cleaners containing
abrasive cleansers, ammonia, bleach, acids, waxes, alcohol, solvents, or other
products not recommended for chrome. This will void the warranty.
10-YEAR MANUFACTURER’S
LIMITED WARRANTY
All parts of this Kingston Brass faucet are warranted to the original
retail purchaser to be free from defects in material and workmanship for a
period of ten(10) years from the date of purchase as shown on the purchaser’s
receipt. This warranty is limited to defective parts only, labor charges
and/or damage resulting from improper installation, repair, or replacements,
as well as incidental and consequential damages connected therewith are
excluded. Any damage to this faucet as a result of misuse, abuse, neglect,
accident, improper installation, or any use not consistent with the
instructions furnished by us, will void this warranty. Replacement parts can
be obtained from your local dealer. Freight cost is not covered by the
manufacturer.
CAUTION!!!
- Water lines must be completely flushed before use, to avoid debris & clogs in your water system leading to a reduction of water flow and mal-functioning.
- Warranty is void if water lines are not flushed prior to use and installation of the new faucet.
- Use of abrasives of any strength may damage the finish of the faucet and void the product warranty.
- Do not over-tighten your faucet on the countertop during installation. The valve assembly is tested to meet the standards set by ASME A112.18.1 sec 5.8 which is listed at 100 LBF. However, over-lightened or over-torqued nuts may lead to cracks on the valve and will eventually lead to leaking and water damage.
- Before installation of the faucet to the desired fixture, you need to secure and anchor your console, sink, tub, or vanity cabinet firmly to the wall and to the floor. To ensure your fixture or faucet mounting surface cannot be moved, before installation of the faucet, please test to see if the cabinet or vanity can be moved by hand or body weight. If the faucet mounting fixture is not secure and anchored, it will eventually crack the valve and cause leaking leading to property damage. In order to avoid this, be sure to secure your installation surface. Do not use any power tools for assembly and installation which can cause internal fractures to the fixture.
PROBLEMS SHOOTING
PROBLEM| CAUSE| CORRECTIVE ACTION
Leaks underneath handle| Bonnet nut has come loose| Remove the handle and
tighten the bonnet nut
Leaks from the spout| The valve seat and spring are worn| Replace the valve
seat and spring
Inconsistent water flow pattern| An aerator is dirty or aged| Release the
aerator and check on the rubber gasket if aged or replace it with a new
aerator
Faucet is dirty| Caused by a stubborn water spot| Clean with mild soap and
warm water as often as possible
Handles work backward| Handle installed backward| Rotate the right stem stop
assembly 180 degrees
CODE APPROVAL: LA#M-000018
Parts·
Washer
&
Lock Nut| Cone Washer
&
Coupling Nut| Pop-Up
---|---|---
2 Pcs| 2 Pcs| 1 Pc
www.kingstonbrass.com
TOLL-FREE CUSTOMER SERVICE: 1-877-2-KBRASS
TECHNICAL SUPPORT
E-mail:service@kingstonbrass.com
12775 Reservoir Street, Chino, CA 91710
Documents / Resources
|
KINGSTON KB8951NDL Brass NuvoFusion Double Handle 4 to 8 Inch Mini Widespread
Lavat
[pdf] Instruction Manual
KB8951NDL, Brass NuvoFusion Double Handle 4 to 8 Inch Mini Widespread Lavat,
KB8951NDL Brass NuvoFusion Double Handle 4 to 8 Inch Mini Widespread Lavat,
Double Handle 4 to 8 Inch Mini Widespread Lavat, Handle 4 to 8 Inch Mini
Widespread Lavat, 8 Inch Mini Widespread Lavat, Mini Widespread Lavat,
Widespread Lavat, Lavat
---|---
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>