LUMANTEK EZ-SHV+ SDI to HDMI Converter with Display and Scaler User Manual

June 6, 2024
LUMANTEK

EZ-SHV+ SDI to HDMI Converter with Display and Scaler

ez-SHV+

SDI to HDMI
Converter with
Display and Scaler

Operation manual
Manual Updated AUGUST. 2020

Copy Rights Copyright © 2006~2020 LUMANTEK Co., Ltd. All Rights Reserved
This document contains information that is proprietary to LUMANTEK. CO., LTD. The information in this document is believed to be accurate and reliable; however, LUMANTEK assumes no responsibility or liability for any errors or inaccuracies that may appear in this document, nor for any infringements of patents or other rights to third parties resulting from its use.
This publication may contain technical issues, inaccurate information or typos. These will be revised in revised edition, if there is any. No part of this publication is subject to be reproduced, stored in retrieval system, or transmitted in any forms, or any means without the prior consent by Lumantek.

Trademarks

HD ENCODULATOR TM, SD ENCODULATOR TM LUMANTEK Logo, Mega CruiserTM, ORIXTM, X-CruiserTM, DTA-PlusTM, Media BlasterTM, are Trademarks of Lumantek. Co., Ltd. Any other trademarks than stated above in this document belongs to its pertinent corporation.

Warranty Period

Lumantek’s products comes with One(1) year limited warranty. Please contact below if you need more information.

LUMANTEK CUSTOMER SERVICES
gs@lumantek.com
TEL: +82-2-6947-7429
FAX: +82-2-6947-7440

01. ez-SHV+

(SDI to HDMI Converter with Display and Scaler)

Lumantek’s ez-SHV+ is an SDI to HDMI converter with Display and Scaler. The ez-SHV+ does more than just coverting. Through its 2.7 inch TFT-LCD, it dislays the video input. The display also shows an eye pattern for video quality monitoring, the resolution of incoming video and approximate cable length relative to the quality of the video.

Features

  1. Inputs & outputs
    Input: 1 x SD/HD/3G-SDI (BNC 75)
    Output: 1 x SD/HD/3G HDMI (Type A)
    1 x SD/HD/3G-SDI loop (BNC 75)
    1 x Analog audio stereo

  2. Supports SD/HD/3G

  3. TFT-LCD Display (2.7 inch)

  4. Push switch for mode change

Diagram
lumantek diagram

02. Interface

Specifications

sdi switchswitch

02. Interface

DIP Switch Settings

 video out|

VIDEO OUT : Video output resolution (Position 1, 2, 3, 4)
– 720x480i@59.94 (DIP SW : 1111)
– 720x576i@50 (DIP SW : 0111)
– 1280x720p@50 (DIP SW : 1011)
– 1280x720p@59.94 (DIP SW : 0011)
– 1280x720p@60 (DIP SW : 1101)
– 1920x1080i@50 (DIP SW : 0101)
– 1920x1080i@59.94 (DIP SW : 1001)
– 1920x1080i@60 (DIP SW : 0001)
– 1920x1080p@23.98 (DIP SW : 1110)
– 1920x1080p@24 (DIP SW : 0110)
– 1920x1080p@25 (DIP SW : 1010)
– 1920x1080p@29.97 (DIP SW : 0010)
– 1920x1080p@30 (DIP SW : 1100)
– 1920x1080p@50 (DIP SW : 0100)
– 1920x1080p@59.94 (DIP SW : 1000)
– 1920x1080p@60 (DIP SW : 0000)

---|---
|

RATIO : Video output screen ratio (Position 5)
– FULL 16:9 (DIP SW : 1)
– Latter 4:3 or Pillar Box (DIP SW : 0)

|

BRIGHTNESS : LCD brightness (Position 6)
– Dark (DIP SW : 1)
– Bright(DIP SW : 0)

02. Interface

LCD Displays

Input Resolution SDI Input resolution Shown as “Unknown” where there is no input. If input is 3G Level-B, 1080P60B will be displayed.

HDMI Output Resolution * Resolution configured through DIP Switch

bar

Input Cable Length Shows approximated cable length in 3 stages (SHORT, MEDIUM, LONG). Please refer to the chart below for your reference. Reference cable is Belden 1694A cables.

Input Video SDI input video display * In case 3G-SDI Level-B is inserted, grey scale bars will be shown instead

SHORT

medium

Input Audio Level Bar Shows Audio Level Bar if input audio signal quality is poor.
Input SDI Eye Pattern Shows thick eye pattern if input video signal quality is poor.

Displays

02. Interface
LCD Displays
LCD Display ON/ OFF

button powerTurn off the display by pressing and holding the mode switch for less than 6 sec


button powerTurn on the display by pressing and holding the mode switch for less than 6 sec

02. Interface

LCD Displays

SDI input eye pattern or audio level meter

pattern powerTurn on the eye pattern by pressing the mode switch for less than 1 sec.


level meterTurn on audio level meter by pressing the mode switch for less than 1 sec.

02. Interface

LCD Displays

LCD monitor rotation (by 0 or 180 degrees)

pattern powerRotate to 0 degrees by pressing and holding for more than 6 sec


rotateRotate to 180 degrees by pressing and holding for more than 6 sec

02. Interface

LCD Displays

ON/OFF HDMI mirrored output for teleprompter HDMI Output

HDMI connecting Please TURN OFF the LCD Display first.
TURN ON the mirrored output application by pressing the mode switch for more than 6 seconds while the LCD OFF.
Please refer to page 9 for the LCD Display ON/OFF
Supports only HD resolutions


HDMI LCDPlease TURN OFF the LCD Display first
TURN OFF the mirrored output application by pressing the mode switch for more than 6 seconds while the LCD OFF.
Please refer to page 9 for the LCD Display ON/OFF
Supports only HD resolutions

03. Product Configuration

ez-SHV+

SHV

AC to DC adapter

Adapter specifications AC in : AC100 to 240V,50/60Hz DC out : DC12V, 1A

04. Technical Specifications

Data Input
SDI Video Input : SD/HD/3G-SDI (BNC 75) x1 Video Formats : – 720x480i@59.94/60 – 720x576i@50 – 1280x720p@50/59.94/60 – 1920x1080i@50/59.94/60 – 1920x1080p@23.94/24/25/29.97/30 – 1920x1080p@50/59.94/60 (3G-SDI Level-B not supported)

Data Output
SDI LOOP Output : SD/HD/3G-SDI (BNC 75) x1 Audio Output : Stereo Jack x1 HDMI Video Output : SD/HD/3G (HDMI Type A) x1 Video Formats : – 720x480i@59.94 (DIP SW : 1111) – 720x576i@50 (DIP SW : 0111) – 1280x720p@50 (DIP SW : 1011) – 1280x720p@59.94 (DIP SW : 0011) – 1280x720p@60 (DIP SW : 1101) – 1920x1080i@50 (DIP SW : 0101) – 1920x1080i@59.94 (DIP SW : 1001) – 1920x1080i@60 (DIP SW :

  1. – 1920x1080p@23.98 (DIP SW : 1110) – 1920x1080p@24 (DIP SW : 0110) – 1920x1080p@25 (DIP SW : 1010) – 1920x1080p@29.97 (DIP SW : 0010) – 1920x1080p@30 (DIP SW : 1100) – 1920x1080p@50 (DIP SW : 0100) – 1920x1080p@59.94 (DIP SW : 1000) – 1920x1080p@60 (DIP SW : 0000)

Connections Power : DC Power Input (DC Jack) x1 DIP Switch : (6 Pole) x1 Video In/Out Resolution, Video Output Ratio, LCD Brightness MODE : (Push Switch) x1 LCD ON/OFF, Menu Selection
Display 2.7 inch TFT LCD : Input Video Display, Input SDI Eye Pattern,In/Output Video Resolution Display, Input Cable Length, Audio Level Meter
Electrical Power Input : DC +5V to +18V Power Consumption : 3W(max.) Operation Temperature : 0~45 C
Physical Dimension : 86.3×57.2×26.6 (mm)(include connector) Weight : 0.3 kg (0.66lbs)

CUSTOMER SERVICES
gs@lumantek.com TEL(Dir) : +82-2-6947-7429 FAX: +82-2-6947-7440

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals