VAVA VA-IH006 Baby Monitor User Guide

June 6, 2024
Vava

VAVA Logo

VAVA VA-IH006 Baby Monitor

VAVA VA-IH006 Baby Monitor

SAFETY INSTRUCTIONS

  • Keep cord out of the reach of children (more than 3ft / 0.9m away) in case of STRANGULATION.

SAFETY INSTRUCTIONS

  • NEVER place the camera or cord in or near the crib or playpen.
  • NEVER mount the camera directly above the crib or playpen to avoid the risk of injury.
  • Only use the AC adapters provided.
  • Never use the unit near water, including near a bathtub, sink, laundry machine tube, wet basement, etc.
  • Do not install near any heat sources such as radiators, heat registers, stoves, or other devices that produce heat.
  • Only use attachments and accessories specified by the manufacturer.
  • Unplug this device when unused for long periods of time.
  • Do not insert anything into the upgrade pinholes. This operation is only intended for professionals.

CAUTION

  • NOT toys. Do not allow children to play with them.
  • The lens and lens hood are small parts, keep them out of your baby’s reach at all times.
  • This product is NOT intended to replace the proper supervision of children. You MUST check your child’s activity regularly.
  • This product is not intended for use as a medical camera and its use should not replace adult supervision.
  • Unplug the product during lightning storms.
  • Please check the operating range and condition of the camera carefully at the initial installation, and on a regular basis after that.
  • Check the reception regularly. Test the camera before use and after changing the camera’s location.
  • For indoor use only.
  • Clean the camera with a dry cloth only.
  • Do not block any ventilation openings.
  • Microphone feedback might occur when the monitor is too close to the camera. Please keep them at least 1.5m / 4.9ft apart.

PACKAGE CONTENTS

PACKAGE CONTENTS

  • Baby Monitor & Camera (Model: VA-IH006)
  • Monitor Adapter with USB-C Charging Cable
  • Camera Adapter
  • Micro-USB Charging Cable
  • Quick Start Guide
  • User Guide

PRODUCT DIAGRAM

Baby Monitor

Baby Monitor

  1. Antenna
  2. Volume Indicators
  3. Microphone
  4. Charging Indicator
  5. Power Indicator
  6. Menu Button
  7. Zoom Button
  8. Left Button
  9. Up Button
  10. Right Button
  11. OK Button
  12. Down Button
  13. Talk Button
  14. Power Button
  15. Upgrade Pinholes
  16. Back Stand
  17. Speaker
  18. USB-C Port
Camera

Camera

  1. Camera Vents
  2. Camera Antenna
  3. Micro-USB Port
  4. Temperature Sensor
  5. Reset Pinhole
  6. Power Switch
  7. Speaker
  8. Lens
  9. Pairing Button
  10. Mounting Hole

GETTING STARTED

  1. Charging & Powering Baby Monitor

    • Connect the monitor adapter to the monitor and a power outlet.
    • Unplug the unit when its power indicator turns off, indicating a full charge.
    • Press the Power button on the monitor to power on with the power indicator lighting green.
  2. Powering Camera

    • Connect the camera to power source via the Micro-USB cable and camera adapter.
    • Slide the Power Switch on camera to power on. Make sure the power indicator light is green.
    • Only use the power adapters included in the package.
    • Do not place the camera and power cord within the reach of your baby.
  3. Pairing the Baby Monitor & the Camera
    By default, one camera has been paired with the monitor when manufactured. When you power on the monitor and camera, the two will automatically pair. To add more cameras, press the Pair Button at the bottom of the camera, press Menu button, select through and then the monitor will auto-pair with the camera.

  4. Placing the Camera
    Place the camera 1.5-2m / 4.9-6.6ft away from your baby for safety reason and for a better view when in night vision mode.
    Placing the Camera

  5. Wall Mounting Camera

    • Select the spot to mount the camera, keeping it beyond your baby’s reach.
    • Insert the screw (not included) pre-installed on wall into the mounting hole of the camera.
      Wall Mounting Camera
  6. Wide-Angle Lens (Optional)
    The aluminum lens hood (no special video effects) has been installed when the camera was manufactured.
    To install wide-angle lens (sold separately), simply rotate the original lens hood counterclockwise to remove. Then install the new lens and rotate clockwise to fix in place.
    Wide-Angle Lens \(Optional\)

FUNCTIONS & OPERATIONS

Monitor Interface Overview

Monitor Interface Overview

Top Status Indications
Signal 4 levels
Current Camera Camera 1 / Camera 2 / Camera 3/ Camera 4
Zoom 2X / 4X
Current Temperature °C / °F
Night Vision Auto ON in a dim environment
Current Time AM / PM
Alarm ON / OFF
Mute Mute all system sounds
Talk-back ON / OFF
Battery 5 levels
Add Camera Max. 4 cameras
View Camera Select to view each at a time
Delete Camera Select to delete cameras
Speaker Volume 0-7 levels (mute when it’s 0)
Brightness 1-8 levels
Camera To add / view / delete cameras
Alarm OFF / 2Hr / 4Hr /6Hr / Set Time (hour / minute / AM, PM)
Settings Time

System sound volume Temperature scale Auto-sleep time
Restore to factory setting Customer service contacts

  1. Monitor Settings
    Press Menu Button, Left and Right Buttons, and then OK Button to set the monitor:

    • Time setting: Set the current time by setting hour, minute, and AM/ PM.
    • System sound volume: Select between Low, High, and Mute.
    • Temperature scale: Select between °C and °F.
    • Screen auto-sleep time: Select between 1min, 2min, 5min, and OFF.
    • Restore to factory settings: Press OK Button to confirm resetting; “Restoring factory settings” will be shown when restoring, and you can’t press any button to control the device during this period. The monitor will auto restart when it’s done.
    • Customer service contacts: Check the email, Tel. number, and address for customer service.
  2. Add / View / Delete a Camera

    • Press Menu button, select through -> -> to add a camera.
    • Select through -> to view a camera.
    • Select through -> to delete a camera.
  3. Digital Zoom & Circulating
    Press Zoom Button to zoom in to 2X / 4X when viewing the camera. A third pressing of the button will restore to the original image.
    Press and hold OK Button 4 seconds to start auto circulating, press OK again to stop.

  4. Pan-n-Tilt
    When viewing the camera, press Left / Right / Up / Down Button to view at different angles, 108 degrees vertically and 270 degrees horizontally.

  5. Volume Adjustment
    Press Menu Button -> OK Button -> Left / Right Button to volume down / up, and OK Button to saving your settings.

  6. Night Vision
    The night vision is automatically activated in a dim environment. The camera has 12 high-intensity infrared LEDs for picking up clear images in the dark. Black and white images can be captured within 2m distance.

  7. Alarm
    Press Menu Button -> Right Button to locate Alarm menu -> OK Button -> Up / Down Button to select the timer setting. You can set a 2Hr, 4Hr or 6Hr alarm, or set the hour and minute otherwise. When the alarm time is reached, a beep will be heard. Press OK Button to stop; otherwise it’ll keep beeping for 30s, beeping again in 1min, stops after it’s alerted 3 times.

  8. Talkback
    Press and hold Talk Button to talk to your baby, release it to exit the talking mode.

  9. Wide-angle Viewing (Optional)
    Install your wide-angle lens (separately sold) referring to the previous mounting wide-angle lens section. Now you can view the camera in a wider angle of about 170 degrees.

  10. Temperature Alert
    The monitor will prompt too high (>35°C / 95°F) and too low (<0°C / 32°F) temperatures with the “HH” and “LL” icon, accompanied with icons  and a beep alert.

SPECIFICATIONS

Monitor

Model|

VA-IH006

---|---
Sonix IC|

SN93700

Resolution|

IPS (720 x 1280), PPI=293

Connectivity|

2.4GHz

Image Aspect|

16:9 (HD720)

Image Compression|

h.264 (frame rate = 18fs)

Operating Range|

280 – 300m (antenna vertically positioned at 90°)

Temperature Alert|

Yes

Volume Control|

8 levels

Brightness|

8 levels

Antenna|

Rotatable (max. 90 degree)

Power Input|

5V / 1.5A (1.5m long USB C cable)

Zoom|

Zoom In (2X) Zoom In (4X)
Auto-Pilot (2 cycles)

Two-Way Talk|

Yes

Multi-Camera|

Max. 4 cameras

Storage Temperature|

-10°C ~ 55°C / 14 – 131°F

Operation Temperature|

0°C ~ 40°C / 32 – 104°F

Camera

Cmos|

720p (1280×720), 3.0M, 1/4″

---|---
Connectivity|

2.4GHz

Image Compression|

h.264 (frame rate = 18fs)

Power Input|

5V / 1.2A, 2.5m-long Micro-USB cable

Pan-n-Tilt|

108 degrees vertical (Up=90, Down=18)
270 degrees horizontal (Left=135, Right=135)

Zoom|

Zoom In (2X) Zoom In (4X)
Auto-Pilot (2 cycles)

View Angle|

Vertical: 1.5m, Horizontal: 1.4m

Lens Focal Length|

1.5m to infinity

Night Vision|

Black & White image, up to 2m clear range

IR LED|

Non-visible IR LED with wavelength 940nm (x 12 pcs)

Light Sensor|

Yes

Two-Way Talk|

Yes

Storage Temperature|

-10°C ~ 55°C / 14 – 131°F

Operation Temperature|

0°C ~ 40°C / 32 – 104°F

TROUBLESHOOTING

Product not powering on?|

  • Check that the camera and monitor are turned on.
  • Check the camera is connected to power properly (it cannot be charged; it’s power off once disconnected from power).
  • Check that the monitor is of enough battery (it’ll auto shut off when battery level icon flashes red slowly on the monitor).
  • Check the intactness of the power cable.

---|---
Baby monitor can’t connect with the camera?|

  • Check whether the camera is near the monitor (recommended to keep within 1.5-2m / 4.9-6.6ft).
  • Check whether the monitor is of low battery. Charge it in time to restore good connection.
  • Check whether the camera is well connected to power.
  • Check whether there are any large metallic objects including doors, refrigerators, mirrors, etc., are placed between the camera and monitor thus blocking the radio signals.
  • Check whether there’s any other 2.4GHz product is used nearby like WiFi routers, microwave ovens, which may interfere the connection.
  • If nothing above is involved, please retry to pair: press the Pair Button at the bottom of the camera, press Menu button, select through and then the monitor will auto-pair with the camera.

Nothing shown when I view a camera?|

  • Check all connections to the camera (power cable plugging and pairing).
  • Check whether the screen is in sleep mode. Press any button to awake it.
  • Check whether the camera is within range of the monitor.
  • Adjust the monitor antenna to vertical position for better signal transfer.

No sound from the monitor?| Check whether the system sound volume is set to “0”. It’ll be mute if set so.
Black and white pictures?| Night vision LED may be ON. Please turn on room lights to force it out of the night mode.
Choppy videos?|

  • Check whether the camera is near the monitor and that there’re no obstacles between them.
  • Adjust the monitor antenna to vertical position for better signal transfer.

Too much noise?|

  • Volume may be set too high. Press Menu Button -> OK Button -> Left Button to volume down.
  • The camera and monitor may be put too close; keep them at least 1.5m / 4.9ft apart.
  • The camera may be too out of range. Please keep it within 10m / 32.8ft to the monitor.

WARRANTY & CUSTOMER SERVICE

18 months warranty
Lifetime customer service (contacts on the monitor, and back cover of this User Guide)

FCC STATEMENT

changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

  1. this device may not cause harmful interference, and
  2. this device must accept any interference received, including interference that may cause undesired operation.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.
15.21& SAR Statements

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. End user must follow the specific operating instructions for satisfying RF exposure compliance. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
The mobile device is designed to meet the requirements for exposure to radio waves established by the Federal Communications Commission (USA). These requirements set a SAR limit of 1.6 W/kg averaged over one gram of tissue. The highest SAR value reported under this standard during product certification for use when properly worn on the body is 0.515 W/kg.
For body operation, this device has been tested and meets FCC RF exposure guidelines when used with any accessory that contains no metal and that positions a minimum of 15mm from the body. Use of other accessories may not ensure compliance with FCC RF exposure guidelines.

FCC 20cm Statement

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator & your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

IC STATEMENT

This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-ex-empt RSS(s). Operation is subject to the following two conditions:

  1. This device may not cause interference.
  2. This device must accept any interference, including interference that may cause undesired operation of the device.

The device meets the exemption from the routine evaluation limits in section 2.5 of RSS 102 and compliance with RSS-102 RF exposure, users can obtain Canadian information on RF exposure and compliance.
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body.

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals