VAVA VA-IH019 Baby Monitor User Guide

: June 9, 2024
: Vava

VAVA VA-IH019 Baby Monitor

SAFETY INSTRUCTIONS

Keep cord out of the reach of children (more than 3ft / 0.9m away) in case of STRANGULATION.
NEVER place the camera or cord in or near the crib or playpen.
NEVER mount the camera directly above the crib or playpen to avoid the risk of injury.
Only use the AC adapters provided.
Never use the unit near water, including near a bathtub, sink, laundry machine tube, wet basement, etc.
Do not install near any heat sources such as radiators, heat registers, stoves, or other devices that produce heat.
Only use attachments and accessories specified by the manufacturer.
Unplug this device when unused for long periods of time.
Do not insert anything into the upgrade pinholes. This operation is only intended for professionals.

CAUTION

NOT toys. Do not allow children to play with them.
The lens and lens hood are small parts, keep them out of your baby’s reach at all times.
This product is NOT intended to replace the proper supervision of children. You MUST check your child’s activity regularly.
This product is not intended for use as a medical camera and its use should not replace adult supervision.
Unplug the product during lightning storms.
Please check the operating range and condition of the camera carefully at the initial installation, and on a regular basis after that.
Check the reception regularly. Test the camera before use and after changing the camera’s location.
For indoor use only.
Clean the camera with a dry cloth only.
Do not block any ventilation openings.
Microphone feedback might occur when the monitor is too close to the camera. Please keep them at least 1.5m / 4.9ft apart.

PACKAGE CONTENTS

Baby Monitor & Camera(Model: VA-I HO19)
Monitor Adapter with TYPE-C Charging Cable
Camera Adapter with Micro-USS Charging Cable
Quick Start Guide
User Guide

PRODUCT DIAGRAM

Baby Monitor

Antenna
Volume Indicators
Microphone
Charging Indicator
Power Indicator
Menu/Back Button
Zoom Button
Left Button
Up Button
Right Button
OK Button
Down Button
Talk / Shortcut Button
Power Button
Back Stand
Speaker
Type-C Port

Camera

Camera Vents
Camera Antenna
Micro-USS Port
Temperature Sensor
Power Indicator
Power Switch
Speaker
Lens
Mounting Hole
Pairing Button

GETTING STARTED

Charging & Powering Baby Monitor

Connect the monitor adapter to the monitor and a power outlet.
Unplug the unit when its power indicator turns off, indicating a full charge.
Press the Power button on the monitor to power on with the power indicator lighting green

Powering Camera

Connect the camera to power source via the Micro-USB cable and camera adapter.
Slide the Power Switch on camera to power on. Make sure the power indicator light is green.

Only use the power adapters included in the package.
Do not place the camera and power cord within the reach of your baby.

Pairing the Baby Monitor & the Camera

By default, one camera has been paired with the monitor when manufactured. When you power on the monitor and camera, the two will automatically pair. To add more cameras, press the Pair Button at the bottom of the camera, press Menu button, select through -> , and then the monitor will auto-pair with the camera.

· Once they’re paired successfully, the camera number with icon will be shown at the top left.
· Microphone feedback might occur when the monitor is too close to the camera. Please keep them at least 1.5m / 4.9ft apart.
· It is recommended to pair in the baby’s room, or wherever you intend to place the camera.

Placing the Camera

Place the camera 1.5-2m / 4.9-6.6ft away from your baby for safety reason and for a better view when in night vision mode.

Wall Mounting Camera

Select the spot to mount the camera, keeping it beyond your baby’s reach.
Insert the screw (not included) pre-installed on wall into the mounting hole of the camera.

It’s strongly recommended to use a screw and screw anchor. Don’t release the camera until you’re sure it is firmly mounted.

Wide-Angle Lens (Optional)

The aluminum lens hood (no special video effects) has been installed when the camera was manufactured.
To install wide-angle lens (sold separately), simply rotate the original lens hood counterclockwise to remove. Then install the new lens and rotate clockwise to fix in place.

FUNCTIONS & OPERATIONS

Monitor Interface Overview

Top Status Indications

| Signal| 5 levels
---|---|---
| Current Camera| Camera 1 / Camera 2 / Camera 3/ Camera 4
| Zoom| 2X / 4X
| Current Temperature| °C / °F
| Night Vision| Auto ON in a dim environment
| Current Time| AM/PM
| Alarm| ON /OFF
| Mute| Mute all system sounds
| Talk-back| ON /OFF
| Battery| 5 levels

| Add Camera| Max. 4 cameras
---|---|---
| View Camera| Select to view each at a time
| Delete Camera| Select to delete cameras
| Speaker Volume| 0-?levels (mute when it’s 0)
| Brightness| 1-8 levels
| Camera| To add / view / delete cameras
| Music| Accommodates 5 lullabies
Remote control of single or multiple selection loop playback
Adjustable lullaby playback volume
| Alarm| OFF/ 2Hr / 4Hr /6Hr / Set Time (hour/ minute/ AM, PM)
| Settings| Time
System sound volume
Temperature scale
Auto-sleep time
Multi country voice settings
Low/medium/high/off setting
Restore to factory setting
**** Customer service contacts

Volume Adjustment

Use Shortcut Button: Press Talk Button ->Left/ Right Button to quickly adjust the volume with & icons.

For system sound adjustment, please go to Monitor Settings -> System sound volume.

Display Brightness Adjustment

Use Shortcut Button: Press Talk Button ->Up/ Down Button to quickly adjust the brightness with & icons.
Or you can press Menu Button -> OK Button ->Left/ Right Button to turn up / down the brightness, and OK Button to saving your settings.

Talkback

Press Talk/ Shortcut Button once to quickly adust the Volume or Brightness.
Press and hold Talk Button to talk to your baby, release it to exit the talking mode.

When you enter the talking mode, the icon will be shown on the monitor.
When it’s mute or the speaker volume is too low, you may not be able to hear the baby.
When you’re pressing the Talk Button, the camera will not transfer the sound to the monitor. Please release the button to listen to your baby.

Monitor Settings

Press Menu Button, Left and Right Buttons, and then OK Button to set the monitor:

Time setting: Set the current time by setting hour, minute, and AM/ PM.
System sound volume: Select between Low, High, and Mute.
Temperature scale: Select between °C and 0 F.
Screen auto-sleep time: Select between l min, 2min, 5min, and OFF.
Multi language settings: English, French, German, Spanish, Italian.
Sound: automatically detect the baby’s crying, wake up the display screen, and send out a prompt tone; The sensitivity can be set to low, medium, high or off.
Restore to factory settings: Press OK Button to confirm resetting; “Restoring factory settings” will be shown when restoring, and you can’t press any button to control the device during this period. The monitor will auto restart when it’s done.
Customer service contacts: Check the email, Tel. number, and address for customer service.

To mute the sound during poor monitor-camera connection, please set the system sound volume to mute.
When the monitor screen is under sleep mode, the power indicator flashes green slowly while the audio is still on; press any button to awoke. You con also short press the Power Button to turn the screen off.
Press and hold the Power Button to power on / off the monitor.

Add /View/ Delete a Camera

Press Menu button, select through -> -> to odd a camera.
Select through -> to view a camera.
· If there ore 2 or more cameras, top to cycle through the added cameras every 15 seconds.
· Select the camera number (1/2/3/4) to view the corresponding camera.
Select through -> to delete a camera. At least one camera shall be added. Do not delete all the cameras. If necessary, please odd a new camera before deletion.

You con switch viewing different cameras; the current camera number will be shown with the Camera icon on the monitor. You con only select one camera to view at one time.

Digital Zoom & Circulating

Press Zoom Button to zoom in to 2X / 4X when viewing the camera. A third pressing of the button will restore to the original image.
Press and hold OK Button 4 seconds to start auto circulating, press OK again to stop.

The current zoom level number will be shown with the Zoom icon on the monitor.

Pan-n-Tilt

When viewing the camera, press Left / Right / Up / Down Button to view at different angles, 108 degrees vertically and 270 degrees horizontally.

Night Vision

The night vision is automatically activated in a dim environment. The camera has 12 high-intensity infrared LEDs for picking up clear images in the dork. Block and white images con be captured within 2m distance.

Alarm

Press Menu Button-> Right Button to locate Alarm menu-> OK Button-> Up / Down Button to select the timer setting. You con set a 2Hr, 4Hr or 6Hr alarm, or set the hour and minute otherwise. When the alarm time is reached, a beep will be heard. Press OK Button to stop; otherwise it’ll keep beeping for 30s, beeping again in 1 min, stops after it’s alerted 3 times.

When the timer is set, the Alarm icon will be shown on the monitor.
Before setting, please check that the monitor time is your current , time.

Wide-angle Viewing (Optional)

Install your wide-angle lens (separately sold) referring to the previous mounting wide-angle lens section. Now you con view the camera in a wider angle of about 170 degrees.

Temperature Alert

The monitor will prompt too high (>35°C / 95°F) and too low (<0°C / 32°F) temperatures with the “HH” and “LL:’ icon, accompanied with a & icon and a beep alert.

When the monitor is mute, you may not be able to hear the baby.

SPECIFICATIONS

Monitor

Resolution	I PS(1920×1080),PPI =400
Connectivity	2.4GHz
Image Aspect	16:9( FHD10 80 )
Image Compression	h.264 (frame rate = 15fs)
Operating Range	280 – 300m (antenna vertically positioned at 90°)
Temperature Alert	Yes
Volume Control	8 levels
Brightness	8 levels
Antenna	Rotatable (max. 90 degree)
Power Input	5V / 2A (1.5m long TYP E-C cable)
Zoom	Zoom In (2X) Zoom In (4X)

Auto-Pilot (2 Cycle)
Two-Way Talk| Yes
Multi-Camera| Max. 4 cameras
Storage Temperature| -10°C – 55°C / 14 – 131°F
Operation Temperature| 0°C ~ 40°C / 32 – 104 °F

Camera

Cmos	1080 p(1920 x10 8 0 ),2.0 M, 1/2.9″
Connectivity	2.4GHz
Image Compression	h.264 (frame rate = 15fs)
Power Input	5V / 1.2A, 1.5m-long Micro-USB cable
Pan-n-Tilt	108 degrees vertical (Up=90, Down=18)

TROUBLESHOOTING

Product not powering on?|

Check that the camera and monitor are turned on.
Check the camera is connected to power properly (it cannot be charged; it’s power off once disconnected from power).
Check that the monitor is of enough battery (it’ll auto shut off when battery level icon flashes red slowly on the monitor).
Check the intactness of the power cable.

---|---
Baby monitor can’t connect with the camera?|

Check whether the camera is near the monitor (recommended to keep within 1.5-2m / 4.9-6.6ft).
Check whether the monitor is of low battery. Charge it in time to restore good connection.
Check whether the camera is well connected to power.
Check whether there are any large metallic objects including doors, refrigerators, mirrors, etc., are placed between the camera and monitor thus blocking the radio signals.
Check whether there’s any other 2.4GHz product is used nearby like WiFi routers, microwave ovens, which may interfere the connection.
If nothing above is involved, please retry to pair: press the Pair Button at the bottom of the camera, press Menu button, select through -> -> , and then the monitor will auto-pair with the camera.

Nothing shown when I view a camera?| Check all connections to the camera (power cable plugging and pairing).
Check whether the screen is in sleep mode. Press any button to awake it.
Check whether the camera is within range of the monitor.
Adjust the monitor antenna to vertical position for
No sound from the monitor?| better signal transfer.
Check whether the system sound volume is set to “0”. It’ll be mute if set so.
Black and white pictures?| Night vision LED may be ON. Please turn on room lights to force it out of the night mode.
Choppy videos?| Check whether the camera is near the monitor and that there’re no obstacles between them.
Adjust the monitor antenna to vertical position for better signal transfer.
Too much noise?| Volume may be set too high. Press Menu Button -> OK Button -> Left Button to volume down.
The camera and monitor may be put too close; keep them at least 1.5m / 4.9ft apart.
The camera may be too out of range. Please keep it within 10m / 32.8ft to the monitor.
Software Version?| Press the Power button on the monitor to turn off the monitor. The software version will be displayed at the screen bottom before power off.

WARRANTY & CUSTOMER SERVICE

12 months warranty
Lifetime customer service (contacts on the monitor, and back cover of this User Guide)

FCC STATEMENT

NOTE: This equipment hos been tested and found to comply with the limits for a Class B digital device, pursuant to port 15 of the FCC Rules. These limits ore designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and con radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which con be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into on outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or on experienced radio/TV technician for help

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

This device complies with Port 15 of the FCC Rules. Operation is subject to the following two conditions:

this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

FCC RF Exposure Warning Statements for Camera

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment shall be installed and operated with minimum distance 20cm between the radiator & body.

FCC RF Exposure Warning Statements for Monitor:

FCC RF Exposure requirements: The highest SAR value reported under this standard during product certification for use next to the head with the minimum separation distance of 0mm. This transmitter must not be collocated or operating in conjunction with any other antenna or transmitter.
This product is compliance to FCC RF Exposure requirements and refers to FCC website https://apps.fcc.gov/oetcf/eas/reports/GenericSearch. cfm search for FCC ID: 2A2R7VA-IH019B This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions:

This device may not cause interference.
This device must accept any interference, including interference that may cause undesired operation of the device.

ISED Radio Frequency Exposure Statement for Camera
This equipment complies with IC exposure limits set forth for an uncontrolled environment. The device con be used in portable exposure conditions. This equipment shall be installed and operated with minimum distance 20cm between the radiator & body.

ISED Radio Frequency Exposure Statement for Monitor:

This EUT is compliance with SAR for general population/uncontrolled exposure limits in IC RSS-102 had been tested in accordance with the measurement methods and procedures specified in IEEE 1528 and IEC 62209. This equipment should be installed and operated with minimum distance 0 mm between the radiator and your body. This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitter.