VAVA VA-LTS006 100-Inch ALR Screen for UST Projector User Manual

June 5, 2024
Vava

VAVA VA-LTS006 100-Inch ALR Screen for UST Projector

IMPORTANT SAFETY INSTRUCTIONS

READ AND FOLLOW ALL SAFETY INFORMATION AND INSTRUCTIONS. KEEP FOR FUTURE REFERENCE.

CAUTION

For optimal projection, safe installation and long lasting use of the screen, please always follow below instructions carefully:

  •  Always handle the screen on a clean, level surface covered with clean cloth, film, etc.
  •  Gently hold and put down the unit to avoid any damage to the screen surface.
  •  Do not touch the screen surface by hand. Before handling the screen, put on the pairs of gloves to avoid fingerprint, dust or hand oil on the screen surface.
  •  Do not poke the screen surface with any sharp or hard objects to avoid scratches or tears.
  •  It is recommended to clean the screen once every two weeks.
  •  Wipe clean the screen with a soft cloth and lukewarm water. For general dust, use a soft brush (rough towels or cloth may damage the screen) to clean the screen surface.
  •  Do not clean with abrasive detergent, solvent or other coarse chemicals to avoid permanent damage to the screen surface.
  •  You may notice a slight smell for first-time use, which will dissipate over time. If the smell is too strong, open a window to ventilate the room.
  •  Children should be supervised to ensure that they do not play with the screen.
  •  Please contact your local dealer for repair or maintenance. For any questions or concerns, please email us at support@vava.com or call us at 877-969-8282.

READ AND SAVE THESE INSTRUCTIONS

Package Contents

VAVA VA-LTS006 100-Inch ALR Screen for UST Projector
fig 1

Package Contents

Note: Please wear the included protective gloves before handling in case of scratches from metal parts

Assemble the Inner Frames

  1. Splice the two inner horizontal frames. Fix with M5*7 screws.
  2. Insert the four corner connectors into the inner Horizontal and vertical frames. Fix with ST4*8 screws.VAVA VA-LTS006 100-Inch ALR Screen for UST Projector fig 3

Assemble the Inner Frames

Fix the two struts onto the sliders with the included M5*7 screws. Keep them level with each other with a distance of 110cm / 43.3in.

Note: The screen is easy to scratch. Do not poke the screen surface with any sharp or hard objects to avoid scratches or tears.

  1. Place a piece of clean and soft cloth or plastic film onto a flat surface.

  2. 2 Wear the included anti-dirt gloves before handling the screen to avoid fingerprint smudges.

  3. Unpack the screen, gently unroll it onto the cloth or plastic film with its back facing upwards. Caution: Handle with care. Avoid any creases on screenVAVA VA-LTS006 100-Inch ALR Screen for UST Projector fig 7

  4. Insert the fiberglass strips into the screen sides:

  5. longer strip into the short screen side;

shorter strips into the long screen side. Make sure the shorter ones in

the long screen sides are well aligned with each other.

Assemble the Screen

  1. Put the installed inner frame onto the back side of the screen. Pay attention to the labels on the screen for the right orientation and align them well by referring to the marks on the four corners of the screen.
  2. Attach the screen onto the inner frame using the tension springs. Install the tension springs to the four corners in the sequence 1~8 first. Then install the other tension springs to both sides from the frame center as shown below (please pull the springs with force at the same time).VAVA VA-LTS006 100-Inch ALR Screen for UST Projector fig 10
  3. Place the screen upright to check its evenness. Adjust the spring until no wrinkles observed.
    Note:
  •  Pull the tension springs with hooks.
  •  Hang the tension spring on the fiberglass strips.
  •  It is strongly recommended that two people pull the tension springs on opposite sides at the same time.

Assemble the Outer Frames and Corner Protectors

  1. Place the outer frames against the border of the frame, align the four corners. Fix the inner frames with the outer ones using the included ST4*8 screws.
  2. Fix the plastic corner protectors onto the four corners with ST4*8 screws. Make sure they are well aligned with the outer frames in case of falling.

Mount the Screen onto Wall

  1. Please estimate the location of the screen to be mounted as per the projector used. Generally, distance between the lower edge of the frame and ground is 60-80cm / 23.6-31.5in.
    Recommended DistanceVAVA VA-LTS006 100-Inch ALR Screen for UST Projector
fig 13

  2. Use the wall drilling template to locate the position of the four wall hangers holes. Drill as per the holes on wall drilling template.

  3. Then use the Wall Anchors with Screws to fix the four wall hangers onto the wall. Make sure the hangers are level. VAVA VA-LTS006 100-Inch ALR Screen for UST Projector fig 15Note: Use the level ruler to make sure the hangers are level.

  4. Before mounting the screen onto wall, make sure the screen is correctly assembled, then wrap the screen front with the cloth to prevent it from being polluted or scratched.

  5. 5 Mount the screen onto the wall as shown below.

Screen Height Adjustment.

  1. Adjust the screen height via the height adjusters on the struts if you have already fixed the wall hangers (Adjustable range: 7cm / 2.7in from top to bottom).
  2. The height adjusters on the struts are locked to “0” by default.
    1. Please adjust as shown below. Make sure the four height adjusters are set to the same scale. Pre-compressed spring length: 9-10mm / 0.35-0.39 in.VAVA VA-LTS006 100-Inch ALR Screen for UST Projector fig 18
      Model| VA-LTS006
      ---|---
      Gain| 0.6
      Viewing Angle| 160°
      Ambient Light Resistance| 92%
      Projection Size| 2214 x 1245 mm / 87.2 x 49.0 in
      Projection Ratio| 16:9
      Screen Size| 2234 x 1265 mm / 88.0 x 49.8 in
      Screen Weight| 11.1KG/24.47lbs

Warranty and Service

We will provide you with after-sales service based on specific local policies. Please contact your local sales representative or after-sales team for more details.
For any questions or concerns, please email us at support@vava.com or call us at 877-969-8282 (Monday-Friday: 9:00 – 17:00 PST).

NORTH AMERICA
E-maiNORTH AMERICA E-mail: support@vava.com Tel: 1-877-969-8282 (Monday-Friday: 9:00 – 17:00 PST)
MANUFACTURER
Manufacturer: Shenzhen NearbyExpress Technology Development Co., Ltd. Address: Floor 7, Building E, Galaxy World Phase II, Shenzhen, China Tel: 1-877-969-8282 (Monday-Friday: 9:00 – 17:00 PST) Manufacturer: Shenzhen NearbyExpress Technology Development Co., Ltd. Address: Floor 7, Building E, Galaxy World Phase II, Shenzhen, China

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals