VAVA VA-LT030 120 Inch ALR Projector Screen Max Instruction Manual
- June 12, 2024
- Vava
Table of Contents
VAVA VA-LT030 120 Inch ALR Projector Screen Max
IMPORTANT SAFETY INSTRUCTIONS
READ AND FOLLOW ALL SAFETY INFORMATION AND INSTRUCTIONS. KEEP FOR FUTURE
REFERENCE.
CAUTION For optimal projection, safe installation and long-lasting use of
the screen, follow below instructions carefully:
- Always handle the screen on a clean, level surface covered with clean cloth, film, etc.
- Gently hold and put down the unit to avoid any damage to the screen surface.
- Do not touch the screen surface by hand. Use gloves to avoid fingerprints, hand sweat, or dust on the screen surface.
- Do not poke the screen surface with any sharp or hard objects to avoid scratches or tears.
- It is recommended to clean the screen once every two weeks.
- When cleaning, wipe the screen with a soft cloth and lukewarm water. For general dust, use a soft brush to clean the screen surface (rough towels or cloth may damage the screen).
- Do not clean with abrasive detergent, solvent or other coarse chemicals to avoid permanent damage to the screen surface.
- You may notice a slight smell during first-time use, which will dissipate over time. If the smell is too strong, open a window to ventilate the room.
- Children should be supervised to ensure that they do not play with the screen.
- Please contact your local dealer for repair or maintenance. For any questions or concerns, please email us at support@vava.com or call us at 877-969-8282.
Expanded Overview
Package Contents
Specifications
| Model | VA-LT030 |
|---|---|
| Gain | 0.6 |
| Viewing Angle | 160° |
| Ambient Light Resistance | 92% |
| Projection Size | 26761514 mm/105.3559.61 in |
| Projection Ratio | 16:9 |
| Screen Size | 2656×1494 mm/104.57×58.82 in |
| Screen Weight | 12 kg / 26.45 lbs |
ASSEMBLING YOUR SCREEN
Assemble the Inner Frames
- Connect the horizontal frames and fasten the M5*7 screws.
- Insert the four corner connectors into the horizontal inner frames, and fix the corners with M5*7 screws as shown below.
- Install the support rod as shown below.
Assemble the Screen
- Put on gloves and place a clean cloth (or use the packaging material for the screen) on a flat, clean and level surface.
- Unroll the screen, place it face down on the cloth, then insert the fiberglass strips into the screen sides.
Caution: Handle with care. Avoid any creases on the screen.
- Put the assembled frames on the back side of the screen.
Note: short-focus anti-light screen is directional and needs to be well matched with the frames.
- Fix the screen onto the frame with all the springs in order as indicated below (corners, short sides, then long sides).
- Hold the screen upright and ensure that it is taut and flat.
Adjust the springs until no creases observed.
Assemble the Outer Frames
- Place the outer frames against the inner frames, align the fourcorners and fix with the included M4*8 screws.
- Fix the plastic corner protectors onto the four corners.
10-A/10-B: Horizontal Outer Frame 10-C: Vertical Outer Frame
11: Corner Protector
Mount on the Wall
- Estimate the wall mount area for the screen. The lower edge of the screen should be 60-80cm / 23.6-31.5 in above the ground (as shown below).
- Measure the distance between the spots where the wall brackets will be mounted with the included level ruler.
Recommended Distance
Make sure the screen is correctly assembled, then wrap the screen front with the cloth to prevent it from being damaged or scratched.
Drill holes respectively and install the four wall brackets using the wall
anchors with screws.
Note: Make sure the brackets are level with the level ruler.
Mount the screen onto the wall as shown below.
- Insert the lower side of the screen into the lower wall bracket, then push upwards to compress the spring.
- Insert the upper side of the screen into the upper wall bracket, then release.
Screen Height Adjustment
Adjust the upper wall bracket by repositioning the screws and screwing them
into the lower holes (adjustable range: 0 – 50mm).
WARRANTY AND SERVICE
We will provide you with after-sales service based on specific local policies. Please contact your local sales representative or after-sales team for more details.For any questions or concerns, please email us at support@vava.com or call us at 877-969-8282 (Monday – Friday, 9:00 a.m. – 5:00 p.m. PST).
NORTH AMERICA
E-mail: support@vava.com
MANUFACTURER
Manufacturer: Shenzhen NearbyExpress Technology Development Co.,Ltd. Address:
Floor 7, Building E, Galaxy World Phase II, Shenzhen, China
Made in China
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>