makita M6600 Electric Mixing Drill Instruction Manual
- June 6, 2024
- Makita
Table of Contents
INSTRUCTION MANUAL
Mixer
M6600
DOUBLE INSULATION
SPECIFICATIONS
| Model | M6600 |
|---|---|
| No load speed | 0 – 700 min |
| Mixing blade diameter | 165 mm |
| Overall length | 280 mm |
| Net weight | 3.4 kg |
| Safety class | /II |
- Due to our continuing program of research and development, the specifications herein are subject to change without notice.
- Specifications may differ from country to country.
- Weight according to EPTA-Procedure 01/2003
Symbols
The following shows the symbols used for the equipment.
Be sure that you understand their meaning before use.
| |
---|---|---
- Read the instruction manual.
- DOUBLE INSULATION
- Only for EU countries
Do not dispose of electric equipment together with household waste material! In observance of the European Directive, on Waste Electric and Electronic Equipment and its implementation in accordance with national law, electric equipment that have reached the end of their life must be collected separately and returned to an environmentally compatible recycling facility.
Intended use
The tool is intended for mixing wall materials, etc.
(except flammable materials)
Power supply
The tool should be connected only to a power supply of the same voltage as
indicated on the nameplate, and can only be operated on a single-phase AC
supply. They are double-insulated and can, therefore, also be used from
sockets without earth wire.
General Power Tool Safety
Warnings
WARNING Read all safety warnings and all instructions. Failure to
follow the warnings and instructions may result in electric shock, fire,
and/or serious injury.
Save all warnings and instructions for future reference.
The term “power tool” in the warnings refers to your mains-operated (corded)
power tool or battery-operated (cordless) power tool.
Work area safety
-
Keep work area clean and well-lit. Cluttered or dark areas invite accidents.
-
Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases, or dust. Power tools create sparks that may ignite dust or fumes.
-
Keep children and bystanders away while operating a power tool. Distractions can cause you to lose control.
Electrical safety -
Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any adapter plugs with earthed (grounded) power tools. Unmodified plugs and matching outlets will reduce the risk of electric shock.
-
Avoid body contact with earthed or grounded surfaces such as pipes, radiators, ranges, and refrigerators. There is an increased risk of electric shock if your body is earthed or grounded.
-
Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of electric shock.
-
Do not abuse the cord. Never use the cord for carrying, pulling, or unplugging the power tool. Keep cord away from heat, oil, sharp edges, or moving parts. Damaged or entangled cords increase the risk of electric shock.
-
When operating a power tool outdoors, use an extension cord suitable for outdoor use. The use of a cord suitable for outdoor use reduces the risk of electric shock.
-
If operating a power tool in a damp location is unavoidable, use a residual current device (RCD) protected supply. The use of an RCD reduces the risk of electric shock.
-
Use of power supply via an RCD with a rated residual current of 30 mA or less is always recommended.
Personal safety -
Stay alert, watch what you are doing, and use common sense when operating a power tool. Do not use a power tool while you are tired or under the influence of drugs, alcohol, or medication. A moment of inattention while operating power tools may result in serious personal injury.
-
12. Use personal protective equipment. Always wear eye protection. Protective equipment such as dust masks, non-skid safety shoes, hard hats, or hearing protection used for appropriate conditions will reduce personal injuries.
-
Prevent unintentional starting. Ensure the switch is in the off-position before connecting to a power source and/or battery pack, picking up or carrying the tool. Carrying power tools with your finger on the switch or energizing power tools that have the switch on invites accidents.
-
Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left attached to a rotating part of the power tool may result in personal injury. 1
-
Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations.
-
Dress properly. Do not wear loose clothing or jewelry. Keep your hair, clothing, and gloves away from moving parts. Loose clothes, jewellery, or long hair can be caught in moving parts.
-
If devices are provided for the connection of dust extraction and collection facilities, ensure these are connected and properly used. The use of dust collection can reduce dust-related hazards.
Power tool use and care. -
Do not force the power tool. Use the correct power tool for your application. The correct power tool will do the job better and safer at the rate at which it was designed. Use of dust collection can reduce dust- o not force the power tool. Use the correct power tool for your application. The correct power tool will do the job better and safer at the
-
Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be controlled with the switch is dangerous and must be repaired.
-
Disconnect the plug from the power source and/or the battery pack from the power tool before making any adjustments, changing accessories, or storing power tools. Such preventive safety measures reduce the risk of starting the power tool accidentally.
-
Store idle power tools out of the reach of children and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool. Power tools are dangerous in the hands of untrained users.
-
Maintain power tools. Check for misalignment or binding of moving parts, breakage of parts, and any other condition that may affect the power tool’s operation. If damaged, have the power tool repaired before use. Many accidents are caused by poorly maintained power tools.
-
Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control.
-
Use the power tool, accessories and tool bits, etc. in accordance with these instructions, taking into account the working conditions and the work to be performed. Use of the power tool for operations different from those intended could result in a hazardous situation.
Service -
Have your power tool serviced by a qualified repair person using only identical replacement parts. This will ensure that the safety of the power tool is maintained.
-
Follow instructions for lubricating and changing accessories.
-
Keep handles dry, clean and free from oil and grease.
MIXER SAFETY WARNINGS
-
Use auxiliary handle(s), if supplied with the tool. Loss of control can cause personal injury.
-
Hold power tool by insulated gripping surfaces, when performing an operation where the cutting accessory may contact hidden wiring or its own cord. Cutting accessory contacting a “live” wire may make exposed metal parts of the power tool “live” and could give the operator an electric shock.
-
Always be sure you have a firm footing.
Be sure no one is below when using the tool in high locations. -
Hold the tool firmly.
-
Keep hands away from rotating parts.
-
Do not leave the tool running. Operate the tool only when hand-held.
-
Some material contains chemicals that may be toxic. Take caution to prevent dust inhalation and skin contact. Follow material supplier safety data.
SAVE THESE INSTRUCTIONS.
WARNING:
DO NOT let comfort or familiarity with product (gained from repeated use)
replace strict adherence to safety rules for the subject product. MISUSE or
failure to follow the safety rules stated in this instruction manual may cause
serious personal injury.
FUNCTIONAL DESCRIPTION
CAUTION:
- Always be sure that the tool is switched off and unplugged before adjusting or checking the function on the tool.
Switch action
CAUTION:
- Before plugging in the tool, always check to see that the switch trigger actuates properly and returns to the “OFF” position when released.
- The switch can be locked in an “ON” position for ease of operator comfort during extended use. Apply caution when locking the tool in the “ON” position and maintain firm grasp on the tool.
To start the tool, simply pull the switch trigger. Release the switch trigger
to stop.
For continuous operation, pull the switch trigger, push in the lock button and
then release the switch trigger. To stop the tool from the locked position,
pull the switch trigger fully, then release it.
ASSEMBLY
CAUTION:
- Always be sure that the tool is switched off and unplugged before carrying out any work on the tool.
Installing shaft
Tighten the shaft into the shaft holder till the hex nut contacts with the
shaft holder.
Hold the shaft holder with the wrench and tighten the hex
nut with the other wrench in the direction of the arrow.
To mount the mixing blade, install it with the ” UP ” mark on it facing the tool (directing inside).
Install the mixing blade on the top of the shaft and secure it with a hex bolt.
Installing top grip (auxiliary handle)
Screw the top grip on the tool securely.
Pull off the cap from the tool housing. Insert the leaf springs into the groove of the handle part that has the bosses. Then attach them to the bottom of the tool housing.
Attach both of the handle parts and tighten them with the screws securely.
OPERATION
Mixing
CAUTION:
- Do not use to mix flammable material such as paint with thinner used as a solvent. Failure to do so may cause injury.
- Mixing with the mixing blade floating out of the mixing material may cause the material to splash about.
- Always use the top or back grip (auxiliary handle) and firmly hold the tool by top or back grip and switch handle during operations.
- Place the mixing blade under the material fully and turn on the tool after making sure the worksite safety.
- Move the mixing blade up and down during the mixing operation so that the whole part of the material can be mixed.
- When finishing mixing, turn off the tool, make sure that the mixing blade has come to a complete stop, and then pull it out of the vessel.
MAINTENANCE
CAUTION:
- Always be sure that the tool is switched off and unplugged before attempting to perform inspection or maintenance.
- Never use gasoline, benzene, thinner, alcohol, or the like. Discoloration, deformation, or cracks may result.
Replacing carbon brushes
Remove and check the carbon brushes regularly.
Replace when they wear down to the limit mark. Keep the carbon brushes clean
and free to slip in the holders. Both carbon brushes should be replaced at the
same time. Use only identical carbon brushes.
Use a screwdriver to remove the brush holder caps.
Take out the worn carbon brushes, insert the new ones, and secure the brush
holder caps.
To maintain product SAFETY and RELIABILITY, repairs, any other maintenance or
adjustment should be performed by Makita Authorized Service Centers, always
using Makita replacement parts.
Makita Corporation
www.makita.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>