S R Smith ES-STD EnergySaver Standard Thermal Pool Cover User Manual

: June 12, 2024
: S R Smith

Table of Contents

WRITTEN SPECIFICATIONS
Documents / Resources

S R Smith ES-STD EnergySaver Standard Thermal Pool Cover User Manual

WRITTEN SPECIFICATIONS

PE Fabrics:

High Density Polyethylene (HDPE) fabric consist of clear, UV resistant, woven tapes, protected on both sides with 2 mil Low Density Polyethylene (LDPE), UV stabilized with UV inhibitor and chemically resistant coating. Overall thickness: 8 mils (± 0.25 mils). Overall weight: 4.95 ounce/square yard; ASTM D1919-75
Color: blue and black.
Tape count on standard cover (minimum) 12 X 10 per square inch.
Tape thickness (minimum) 1,100 denier.

PE Foam:

Consists of white, closed cell, irradiated cross-linked, ⅛” thick, density: 2 pound per cubic foot, polyethylene and enhanced with proprietary Ethylene Vinyl Acetate (EVA) additive.

Physical Properties:

Tensile strength (Grab Breaking Strength): 371 lbs. (ASTM-D 5034)
Tongue tear resistance: 87 lbs. (ASTM-D 2261)
Mullen burst strength: 500 psi (ASTM-D 751)
Pull strength: 1,260 psi
Seam tear resistance: 85 lbs.
Insulating (‘R’) value: 0.5/ft². hr. ºF/Btu – (ASTM-D 2326)
Flammability: 0 speed rating (ASTM-E 84)
Abrasion resistance: 0.00466 grams/1,000 cycles (ASTM-D 3389)
Laminate has minimum 99% foam-fabric adhesion and maximum 1¼% overall shrinkage after 15 minute full immersion boil test.
Laminate is non-permeable due to closed cell foam, LDPE coating and flame lamination.
Service temperature range: – 40° to + 160° Fahrenheit.
Chemical resistance is excellent due to polyethylene-based material.
Thickness after lamination process: 0.120” (± 0.06”)

Cover Construction:

Laminated materials are sewn together by using double needle, lockstitch machine with size 138 bonded, yarn-dyed black, UV resistant, polyester thread. Encapsulated with four (4) layers of 12 X 10 woven PE fabrics, weighted vinyl straps material is sewn along the length of the cover. Each end of the cover is reinforced with four (4) layers of 12 X 10 woven PE fabrics. Corners are strengthened by folding (doubling) the fabric material. Each ‘pull-point’ location is reinforced with six (6) layers of 12 X 10 woven PE fabric, non- corrosive brass grommets and ⅛” thick T-1 PVC load-dispersing plate. Solid ¾” diameter white Ultra High Molecular Weight polyethylene (UHMW-PE) dowel coupled with ¼” solid braided white polyester cord is securely tied to the ‘pull-point’ of the cover for easy cover retrieval. Ladder and rail cut-outs, hinges and rounded corners are incorporated into the cover(s) (note: precautions are taken by rounding and reinforcing cut-out corners to prevent stress tears).

ASTM approved safety /warning labels shall be securely attached to each completed pool cover. And in accordance with ASTM standards, safety/warning labels are positioned in such a way that they are visible from and around the pool deck.

Cover Configuration and Dimensions:

Cover configuration and dimensions are customized for each application.

Specification Number:| SRS-1102| S.R. Smith, LLC 1017 SW Berg Parkway Canby, Oregon 97013 Tel: 1 800-824-4387 www.srsmith.com
---|---|---
Product Description:| ENERGYSAVER STANDARD
S.R. Smith Part Number:| ES-STD
Revision:| A1| Date: 7/30/2020
Written By:| C. Redelfs| Date: 6/1/2020
Approved By:| | Date:
Proprietary and confidential: The information contained in this specification is the sole property of S.R. Smith LLC. Any reproduction in part or whole without the written consent of S.R. Smith LLC is prohibited.

Page 2 of 2 SRS-1102

Product Part Number(s): ES-STD
Product Description: ENERGY SAVER STANDARD

S R Smith Logo

Documents / Resources

| S R Smith ES-STD EnergySaver Standard Thermal Pool Cover [pdf] User Manual
ES-STD EnergySaver Standard Thermal Pool Cover, ES-STD, EnergySaver Standard Thermal Pool Cover, Standard Thermal Pool Cover, Thermal Pool Cover, Pool Cover, Cover
---|---